Winners Only BD3001CKHN User manual

PROD. NO.:
NOTE: Bunkie Board must be used to replace Box Spring.
NO QTY
A HB Left Leg 1 PC NO Description Size Sketcher QTY
B HB Right Leg 1 PC 1 Allen Key 4*74*29mm 1 PC
C Headboard 1 PC 2 Bolt 1/4"*15*45mm 20 PCS
D Wood stretcher 1 PC 3 Spring Washer 1/4"*11*2mm 20 PCS
E Panel Footboard 1 PC 4 Flat Washer 1/4*18*2mm 20 PCS
F Side Rail 2 PCS 5 Screw Ø8*30mm 10 PCS
G Slat 5 PCS
H Support Leg 10 PCS
I Rail Cap 2 PCS
Page 1 of 2 MADE IN VIETNAM
DESCRIPTION
Hardware List:
Components List:
WINNERS ONLY ®
ASSEMBLY INSTRUCTIONS
BD3001CKHN/BD3001KHN
BD3001CKFN/BD3001KFN
BD3001CKRN
Thank you for purchasing this quality product. Please read the instructions thoroughly before unpacking the assembly parts.
Caution: sharp exposed staple tips can cause injury, therefore for your protection, please remove any exposed staples used in packing.
Please keep all hardware parts out of the reach of children.
1. We recommend that you should assemble this product with the assistance of another person; this will make the assembly easier, and will help to prevent personal injury and to
insure parts are not damaged during the assembly process.
2. Before beginning, please check the packing materials carefully for small parts which may have come loose inside the carton during shipping. Please do not discard any packing
material until all parts have been located. If any parts are missing, please contact your dealer for prompt replacement.
3. To prevent damage to your floor or carpet, please check the bottom of each piece of furniture for stain residues and rough surfaces and also check for staples or nails left after
removing the packing materials. The manufacturer will not be held responsible if preventive steps are not taken prior to installation.
4. Please do not over tighten screws or bolts. During normal use everyday, screws, bolts, nuts and wooden plugs may loosen up. They should be periodically inspected and re-
tightened to prevent damage to the furniture and (or) personal property or cause injury. Always check to be sure all hardware on this list and the below mentioned components are attached to
the furniture properly and kept tightened.
5. Please lay all parts and hardware on a non abrasive surface such as a carpet, and follow the assembly steps.
STEP 1:
Lay the Headboard (C) front side down on a smooth and clean
surface.
Attach HB Left Leg (A) and HB Right Leg (B) to Headboard (C) using
Flat Washer (4), Spring Washer (3), Bolt (2). Do not fully tighten
yet.
Attach Wood Stretcher (D) to HB Left (A) and HB Right legs (B)
using Flat Washer (4), Spring Washer (3
)
, Bolt (2), fully tighten with
Allen Key (1).
Fully tighten all the bolts located in HB Left Leg (A) and HB Right
Leg (B).
FIG 1
(C)
(A)
(D)
(B)

PROD. NO.:
Page 2 of 2 MADE IN VIETNAM
WINNERS ONLY®
ASSEMBLY INSTRUCTIONS
BD3001CKHN/BD3001KHN
BD3001CKFN/BD3001KFN
BD3001CKRN
STEP 2
FIG 3
STEP
2: Hook both Side Rails (F) to the Headboard
assembly and to the Footboard (E) as shown in FIG
2.
FIG 2
STEP 3
(F)
(F)
(E)
(H)
(I)
STEP 4
STEP 5: Attach the rail caps (I) to side rails (F), using
bolt(2), spring washer (3), flat washer (4) and tighen them
by Allen Key (1).
STEP 5
(F)
(F)
(J)
STEP 3: Attach Support Legs (I) to the Slat (H) as shown in
FIG 3.
STEP 4: Attach Slat with Support Legs (I&H) to the Side
Rails (F) using Screws (6) as shown in FIG 3.
FIG 3
FIG 4
Assembly is now completed !