Winners Only GX164PT-PB User manual

ASSEMBLY INSTRUCTIONS
WINNERS ONLYR
PROD. NO : GX164PT-PB
Thank you for purchasing this quality product. Be sure to check all packing material carefully for small parts that may have come loose inside the carton
during shipment.
Components List :
DESCRIPTION
NO SIZE
Flat Washer
15
16 " x 22 mm
SKETCH QTY
Spring Washer
25
16 "
3
4
8pcs
8pcs
Reminders
1. Use only the hardware supplied.
2. Once the Table is finished, level and tighten all the bolts.
3. Do not over tighten bolts.
4. This item may require periodic tightening.
NOTE :
1. Hardware pack is located underneath the Table Top (A).
2. Two or more people are needed for assembly. Please keep all hardware
part out the reach of children.
1 OF 3
MADE IN MALAYSIA
NO SKETCH QTY
Wrinting
Desk
Top
A1pc
DESCRIPTION
B2pcs
Pedestal
Hardware List :
8pcs
Please keep all hardware parts out of the reach of children.
1. We recommend that you should assemble this product with the assistance of another person; this will make the assembly easier, and will help to prevent personal injury and to insure parts
are not damaged during the assembly process.
2. Before beginning, please check the packing materials carefully for small parts which may have come loose inside the carton during shipping. Please do not discard any packing material
until all parts have been located. If any parts are missing, please contact your dealer for prompt replacement.
3. To prevent damage to your floor or carpet, please check the bottom of each piece of furniture for stain residues and rough surfaces and also check for staples or nails left after removing the
packing materials. The manufacturer will not be held responsible if preventive steps are not taken prior to installation.
4. Please do not over tighten screws or bolts. During normal use everyday, screws, bolts, nuts and wooden plugs may loosen up. They should be periodically inspected and re-tightened to
prevent damage to the furniture and (or) personal property or cause injury. Always check to be sure all hardware on this list and the below mentioned components are attached to the
furniture properly and kept tightened.
5. Please lay all parts and hardware on a non abrasive surface such as a carpet, and follow the assembly steps.
TIP: Store the Allen key and (or)Wrench used in assembly in this product's drawer or use masking or painter's tape to
affix it to the underside of the product.This will make it easier to find if you want to periodically tighten bolts or
disassemble the product.
1pc
NO SKETCH QTY
Pedestal
Leg
D2pcs
DESCRIPTION
5
M5
20pcs
Mounting
Plate
E2pcs
JCBC Bolt
Allen Key M5
C4pcs
Pedestal
Sides
M8 x 80mm
6
7
1
4 " x 16 mm
1
4"20pcs
20pcs
1pc
8
Flat Washer
Spring Washer
Allen Key
JCBC Bolt M6 x 35mm
M4
Post

ASSEMBLY INSTRUCTIONS
WINNERS ONLYR
2 OF 3
Step 1 Tighten the pedestal Post (B) to the pedestal leg (D)
using the hardware provided.
Step 2
Step 3
1
2
3
4
B
B
B
D
D
D
1
2
3
4
D
B
C
C
C
B
D
C
D
D
5
6
7
8
E
E
BC
C
C
C
B
D
4
5
6
7
8
E
B
E
PROD. NO : GX164PT-PB
Tighten the pedestal sides (C) to the pedestal leg (D)
using the hardware provided.
Turn upright Position the Pedestal/ Base and
Connect the mounting plate(E) with the pedestal
base using the hardware provided.

ASSEMBLY INSTRUCTIONS
WINNERS ONLYR
3 OF 3
Step 4
Thank you for your purchase
Assembly Completed !!
PROD. NO : GX164PT-PB
D
D
C
C
A
EE
5
6
7
8
E
C
A
Turn the Writing Desk Top (A) upside down on a
Protective surface such as a carpet or other soft
material. Tighten the pedestal base to the Writing
Desk Top (A) using the hardware provided.
Step 5 Turn the Writing Desk Top (A) to an upright
position.