Winners Only DB2451SP User manual

PAGE 1 OF 3 MADE IN MALAYSIA
ARS-19284-SHNWU2
DB2451SP
PROD . NO:
Thank you for purchasing this quality product. Please read the instruction thoroughly before unpacking the
assembly parts.
Caution: Sharp exposed staple tips can cause injury, therefore for your protection, please remove
any exposed staple used in packing.
Please keep all hardware parts out of the reach of children.
1.We recommend that you should assemble this product with the assistance of another person: this will make the
assembly easier,and will help to prevent personal injury and to insure parts are not damaged during the
assembly process.
2.Before beginning,please check the packing materials carefully for small parts which may have come loose
inside the carton during shipping. Please do not discard any packing material until all parts have been located.
If any parts are missing, please contact your dealer for prompt replacement.
3.To prevent damage to your floor or carpet, please check the bottom of each piece of furniture for stain residues
and rough surfaces and also check for staples or nails left after removing the packing materials. The manufacturer
will not be held responsible if preventive steps are not taken prior to installtion.
4. Please do not over tighten screws or bolts. During normal use everyday,screw,bolts,nuts and wooden plugs
may loosen up. They should be periodically inspected and re-tightened to prevent damage to the furniture
and (or) personal property of cause injury. Always check to be sure all harware on this list and the below
mentioned components are attached to the furniture properly and kept tightened.
5.Please lay all parts and hardware on a non abrasive suface such as a carpet,and follow the assembly.
WINNERS ONLY
Pan Head Screw 4pcs
Flat Washer
Allen Key
Lock Washer
JCBC Bolt
8 x 1 1/4”
M6 x 70mm
M6 x 13mm
M6.5 x 16.5mm
M4 x 2.1/2”
8 pcs
8 pcs
8 pcs
1pce
1
2
3
4
5
This product will take 15-20
minutes to assemble.
Screw driver is require for assembly (not included)
TIP:store the Allen key and or Wrench used in assembly
in this product’s drawer or use masking or painter’s tape
to affix it to the underside of the product .this will make it
easier to find if you want to periodically tighten bolts or
disassemble the product.
Back Rest
Left Front Leg
Right Front Leg
Left Back Leg
Right Back Leg
Side Stretcher
NO
COMPONENT LIST:
SKETCH
DESCRIPTION QTY
1 pce
2 pcs
1 pce
1 pce
1 pce
1 pce
Hardware Bag 1pack
A
B
C
D
F
G
E
NO SKETCHSIZE
DESCRIPTION QTY

PAGE 2 OF 3 MADE IN MALAYSIA
ARS-19284-SHNWU2
Left Back Leg
Right Back Leg
DB2451SP-02
DB2451SP-03
DB2451SP-04
DB2451SP-05 DB2451SP-06
DR2453S-07
DB2451SP
COMB BACK SIDE CHAIR
Allen Key
Flat Washer
Lock Washer
JCBC Bolt
WINNERS ONLY
ASSEMBLY :
STEP 1
1. Position the back rest on a soft surface such as a carpet.
1.1. Insert JCBC Bolt through a Lock Washer and a Flat Washer into the pre-drilled holes on the apron frame at rear corners.
(Fig.1.1)
BL
BL
FL
BR
BR
FR

PAGE 3 OF 3 MADE IN MALAYSIA
CARE INSTRUCTION
~ Be sure to use the same type of polish consistenly.
Your furniture will appear cloudy or streaky if oil
based or wax based polishes are interchanged.
~ Spray your furniture surface evenly. Wipe in a
circular motion with a soft clean cloth.
ARS-19284-SHNWU2
Left Front Leg
Right Front Leg
Side Stretcher
STEP 2
DB2451SP
COMB BACK SIDE CHAIR
Pan Head
Screw
Allen Key
Flat Washer
Lock Washer
JCBC Bolt
WINNERS ONLY
ASSEMBLY :
2. Insert each side stretcher( L/R ) into pre-drilled holes on both of the rear legs, make sure that screw holes on the stretcher are facing
down. Place the front legs (L/R) to corner block of the frame, by insert side stretcher (L/R ) together.
2.1. Insert the JCBC Bolt through a Lock Washer, a Flat Washer and the pre-drilled holes of corner block into the pre-drilled holes
on the front leg (L/R), tighten by using the provided Allen Key but do not fully tighten the bolts yet.
2.2. Insert Pan Head Screw into side stretcher (L/R) through the pre-drilled holes, tighten with screw-driver (Not Provided).
(Fig.2.1)
(Fig.2.2)
FL
FR
3.1- Turn the chair to standing position.
3.2-
STEP 3
Check it's balance and tighten all screw and bolts to complete the assembly.