Winners Only DJ33872 User manual

ASSEMBLY INSTRUCTIONS
WINNERS ONLYR
PROD. NO : DJ33872
Thank you for purchasing this quality product. Be sure to check all packing material carefully for small parts that may have come loose inside the carton
during shipment.
Components List :
DESCRIPTION
NO SIZE
Flat Washer
15
16 " x 22 mm
SKETCH QTY
Spring Washer
25
16 "
3
Wrench
412.8 mm
8pcs
8pcs
Reminders
1. Use only the hardware supplied.
2. Once the Table is finished, level and tighten all the bolts.
3. Do not over tighten bolts.
4. This item may require periodic tightening.
NOTE :
1. Hardware pack is located underneath the Table Top (A).
2. Two or more people are needed for assembly. Please keep all hardware
part out the reach of children.
1 OF 2
MADE IN MALAYSIA
NO SKETCH QTY
Table Top
A1pc
DESCRIPTION
B4pcs
Leg
Hardware List :
Hex. Nut 5
16" x 7mm 8pcs
Please keep all hardware parts out of the reach of children.
1. We recommend that you should assemble this product with the assistance of another person; this will make the assembly easier, and will help to prevent personal injury and to insure parts
are not damaged during the assembly process.
2. Before beginning, please check the packing materials carefully for small parts which may have come loose inside the carton during shipping. Please do not discard any packing material
until all parts have been located. If any parts are missing, please contact your dealer for prompt replacement.
3. To prevent damage to your floor or carpet, please check the bottom of each piece of furniture for stain residues and rough surfaces and also check for staples or nails left after removing the
packing materials. The manufacturer will not be held responsible if preventive steps are not taken prior to installation.
4. Please do not over tighten screws or bolts. During normal use everyday, screws, bolts, nuts and wooden plugs may loosen up. They should be periodically inspected and re-tightened to
prevent damage to the furniture and (or) personal property or cause injury. Always check to be sure all hardware on this list and the below mentioned components are attached to the
furniture properly and kept tightened.
5. Please lay all parts and hardware on a non abrasive surface such as a carpet, and follow the assembly steps.
TIP: Store the Allen key and (or)Wrench used in assembly in this product's drawer or use masking or painter's tape to
affix it to the underside of the product.This will make it easier to find if you want to periodically tighten bolts or
disassemble the product.
1pc
NO SKETCH QTY
Center Leaf
C1pc
DESCRIPTION
Allen Key
5M4 1pc
Twist Lock
D4pcs
on
off

ASSEMBLY INSTRUCTIONS
WINNERS ONLYR
PROD. NO : DJ33872
2 OF 2
Step 1 * POWER TOOLS ARE NOT RECOMMENDED.
Step 2
*NOTE: REMOVE
THE TRANSIT
BOLT USING
ALLEN KEY (5)
Assembly Completed !
Step 3
1
2
3
4
*NOTE: REMOVE
BOLT USING
ALLEN KEY (5)
AND KEEP IT FOR
NEXT STEP.
FLIP THE CENTER LEAF TO
REMOVE FROM CENTER
RAIL
INSTALL BACK THE RAIL
STRUCTURE USING
EXISTING BOLT.
CENTER LEAF SELF STORE
A
C
C
A
A
B
B
B
A
C
A
C
B
A
Unlock the Twist lock under
the table before center leaf
assembled then lock it.
on
off
Turn Table Top (A) upside down on soft surface.
Attach table Legs (B) to the table top (A)
using Flat Washer (1) Spring Washer (2)
and Hex Nut (3) tighten and secure using
wrench (4) As shown on figure.
Turn the table to the upright position, unlock the twist lock under the table
top (A) pull the table top (A) from both end. Place the leaf in position close
the table top and lock of the table top (A) to prevent from sliding.
Thank you for your purchase