Winners Only BFC2001Q User manual

Page 1 of 5 MADE IN VIETNAM
PROD.NO : BFC2001Q,BFG2001Q,BFP2001Q
NO. Q' TY
1
3
8pcs
2
4
8*19*2mm
Allen Key
5
24pcs
1pc
Hardware List
4*30*80mm
Allen Bolts
8mm
Spring Washers
Flat Washers 8pcs
DESCRIPTION SIZE SKETCH
Allen bolt 5/16"*70mm 8pcs
6
DESCRIPTION
NO. Q' TY
A1pc
Footboard
B
CHeadboard
D
1pc
1pc
1pc
Components List :
E
FSide rail 2pcs
5/16"*40mm
Center Rail 1pc
WINNERS ONLYR
ASSEMBLY INSTRUCTIONS
"U" Bracket 64*59*52*2 2pcs
9
8pcs
Half moon
washer Ø5/16"
8pcs
Hexagon Ø5/16"*12mm
1pc
Wrench 12mm
7
8
10
Wood stretcher 1pc
G
HB Right Leg
HB Left Leg
Wood Screw #8 *20mm 4pcs
11
Wood Screw #8*32mm 6pcs
12
Roll Slat(13pcs) 1Set
I
Support Leg 3pcs
H
Allen Bolts 1/4"*15mm 8pcs
Thank you for purchasing this quality product . Please read instructions thoroughly before unpacking assembly parts
Caution: Sharp, exposed staple tips can cause injury. Therefore, for your protection, please remove any exposed staples
used in packing.Please keep all hardware parts out of the reach of children.
1.We recommend that you should assemble this product with the assistance of another person; this will make assembly
easier and will help to prevent personal injury and to insure parts are not damaged during assembly process.
2. Before beginning, please check packing materials carefully for small parts that may have come loose inside the carton
during shipping. Do not discard any packing material until all parts have been located. If any parts are missing, please
contact your dealer for prompt replacement.
3. To prevent damage to your floor or carpet, please check the bottom of each piece of furniture for stain residues and
rough surface sand also check for staples or nails left after removing the packing materials .The manufacturer will not be
held responsible if preventive steps are not taken prior to installation.
4. Please do not over tighten screws or bolts. During normal use everyday, screws, bolts , nuts and wooden plugs may
loosen up.They should be periodically inspected and re-tightened to prevent damage to the furniture and (or) personal
property or cause injury.Always check to be sure all hardware on this list and below mentioned components are attached to
the furniture property and kept tightened.
5. Please lay all parts and hardware on a non-abrasive surface such as a carpet and follow the assembly.
TIP: Store the Allen Key and Wrench in assembly
in this product drawer or use masking or painter
tape to affix it to the underside of the
product. This will make it easier to find if you
want to periodically tighten bolts or disassemble
the product.

Page 2 of 5 MADE IN VIETNAM
WINNERS ONLYR
ASSEMBLY INSTRUCTIONS
PROD.NO : BFC2001Q,BFG2001Q,BFP2001Q
D
STEP 1: Screw Metal Bracket to Wood Strecher as shown in FIG.1
2
3
5
1
2
4
5
STEP 2: Attach the wood stretcher (D)
into both Headboard leg (A&B) using
provided hardware shown on FIG.2
D
B
A
12
4
5
12
4
5
C
FIG.1
FIG.2
STEP 3: Attach Headboard (C) to the
Leg Assembly (A,B&D) using provided
hardware shown on FIG.3
FIG.3
FIG.3
10

Page 3 of 5 MADE IN VIETNAM
WINNERS ONLYR
ASSEMBLY INSTRUCTIONS
PROD.NO : BFC2001Q,BFG2001Q,BFP2001Q
2
3
5
82
7
6
9
2
8
7
6
9
10
F
F
FIG.4
FIG.5
FIG.5
STEP 4: Screw Metal Bracket to Footboard (E)
as shown in FIG.4
STEP 5: Attach both Side Rails (F) to Headboard ( A,B,D&C)
and Footboard (E) sung provided hardware shown on FIG.5

G
H
H
H
Page 4 of 5 MADE IN VIETNAM
WINNERS ONLYR
ASSEMBLY INSTRUCTIONS
11
PROD.NO : BFC2001Q,BFG2001Q,BFP2001Q
FIG.6
FIG.7
STEP 6: Attach Slats Support Legs (H) to Slats Support Bar (G) as shown in FIG.6
STEP 7: Insert and screw Slats Support Bar (G)
to fit the metal bracket using provided hardware
as shown in FIG.7

Page 5 of 5 MADE IN VIETNAM
WINNERS ONLYR
ASSEMBLY INSTRUCTIONS
PROD.NO : BFC2001Q,BFG2001Q,BFP2001Q
12
I
STEP 8: Attach the Slats (I) to the Side Rails (F)
using provided hardware as shown in FIG.8
FIG.8
Assembly is now completed.