Winners Only DC34257GT User manual

MADE IN MALAYSIA
Page 1 of 3
DC34257GT&GB
DC34257RT&RB
HARDWARE LIST:
Flat Washer
(Large)
Lock Washer
(Large)
Hex Nut
Wrench
16pcs
20pcs
20pcs
8pcs
4pcs
8pcs
8pcs
1 pc
1 pc
Flat Washer
(Small)
Lock Washer
(Small)
Allen Key
JCBC Bolt
JCBB Bolt
Adjustable
Leveler
Pedestal Stand
Pedestal Leg # 1
Pedestal Leg # 2
COMPONENT LIST:
COMPONENT LIST:
Apron Hinge
Table Top
Leaf Hinge
Table Lock
Mounting Plate
Side Panel
PROD . NO:
WINNERS ONLY
This product will take 15-20
minutes to assemble.
Screw driver is require for assembly (not included)
TIP:store the Allen key and or Wrench used in assembly
in this product’s drawer or use masking or painter’s tape
to affix it to the underside of the product .this will make it
easier to find if you want to periodically tighten bolts or
disassemble the product.
5/6” x 12.5 x 6.5mm
M8 X 18 X 1.2mm
5/16" (M8) x 13.5 x 1.8 mm
M6 x 40mm
M8 x 70mm
M6.5 x 16.5 x 1.2mm
M6 x 13 x 2mm
M4 x 2.1/2”
12.8mm
1
2
3
4
5
7
6
8
9
10
NO SKETCH
DESCRIPTION QTY
1 pce
1 pce
4 pcs
2 pcs
4 pcs
2 pcs
Hardware Bag 1pack
A
B
C
D
F
G
E
NO SKETCH
DESCRIPTION QTY
1 pce
4 pcs
4 pcs
4 pcs
A
B
C
D
NO SKETCH
SIZE
DESCRIPTION QTY
1 pc
Allen Key
M5 X 2 1/2"
Thank you for purchasing this quality product. Please read the instructions thoroughly before unpacking the
assembly parts.
Caution: Sharp exposed staple tips can cause injury, therefore for your protection, please remove
any exposed staples used in packing.
Please keep all hardware parts out of the reach of children.
1.We recommend that you should assemble this product with the assistance of another person: this will make the
assembly easier,and will help to prevent personal injury and to insure parts are not damaged during the
assembly process.
2.Before beginning,please check the packing materials carefully for small parts which may have come loose
inside the carton during shipping. Please do not discard any packing material until all parts have been located.
If any parts are missing, please contact your dealer for prompt replacement.
3.To prevent damage to your floor or carpet, please check the bottom of each piece of furniture for stain residues
and rough surfaces and also check for staples or nails left after removing the packing materials. The manufacturer
will not be held responsible if preventive steps are not taken prior to installation.
4. Please do not over tighten screws or bolts. During normal use everyday,screws,bolts,nuts and wooden plugs
may loosen up. They should be periodically inspected and re-tightened to prevent damage to the furniture
and (or) personal property of cause injury. Always check to be sure all harware on this list and the below
mentioned components are attached to the furniture properly and kept tightened.
5.Please lay all parts and hardware on a non abrasive surface such as a carpet,and follow the assembly.
TBS-16534-PGNWU / TBS-16535-PGNWU

DC34257GT/GB -08/
DC344257RT/B-08
DC34257GT/GB -07/
DC344257RT/B-07
DC34257GT/GB -07/
DC344257RT/B-07
DC34257GT/GB -13/
DC344257RT/B-13
DC34257GT&GB/DC34257RT&RB
WINNERS ONLY
MADE IN MALAYSIA
Page 2 of 3
TBS-16534-PGNWU / TBS-16535-PGNWU
ASSEMBLY :
STEP 1
FIg.1
STEP 1
Level Glide
Wrench
Allen Key M5
Lock Washer
JCBB Bolt
Hex Nut
Lock Washer
Flat Washer
Flat Washer
5
Flat Washer
(Small)
Flat Washer
(Small)
Lock Washer
(Small)
Lock Washer
(Small)
Mounting Plate
Side Panel
Allen Key
Allen Key
JCBC Bolt
JCBC Bolt
Fig.2
Remove
wood strip
Must Remove all 4 Cleats
R
E
M
O
V
E
R
E
M
O
V
E
1.1-Turn the Table Pedestal stand upside down. Attached the base pedestal leg #1 to pedestal leg #2 using
the provided hardware as shown on Fig.1.
1.2-Attached the this Assemble base Legs (1&2) to the pedestal stand with the provided hardware as shown
on Fig 1.
2.1-Turn table top upside down on a soft protective surface such as a carpet , Attached Table Mounting plate
to the table top using the provided hardware as shown on FIg 2.

CARE INSTRUCTION
~ Be sure to use the same type of polish consistenly.
Your furniture will appear cloudy or streaky if oil
based or wax based polishes are interchanged.
~ Spray your furniture surface evenly. Wipe in a
circular motion with a soft clean cloth.
DC34257GT&GB/DC34257RT&RB
WINNERS ONLY
MADE IN MALAYSIA
Page 3 of 3
TBS-16534-PGNWU / TBS-16535-PGNWU
STEP 3
FIg.3
ASSEMBLY :
4.1-Lift up the center leaf from the compartment.
4.2-Flip down the aprons and fold the centre leaf to store within the compartment
STEP 4
Flip up Apron
STEP 5
5.1-Push Table Top from both ends to close.Lock the metal catches underneath the table.
Metal Catches
Lock
Wrench
Hex Nut
Lock Washer
Flat Washer
UnLock
Metal Catches
3.1- Unlock the metal catches from underneath the table Top and pull the table from both ends. Attached base assembly to the
table top mounting plate using the supply hardware as shown on Fig.3