Wiznet WIZ810Sio User manual

WIZ810Sio User Manual (WIZnet Co.,Ltd.)
1
WIZ810Sio User Manual
(Version 1.0)
©2018 WIZnet Co.,Ltd. All Rights Reserved.
☞For more information, visit our website at http://www.wiznet.io

WIZ810Sio User Manual (WIZnet Co.,Ltd.)
2
Document Revision History
Date
Revision
Changes
2018-12-28
V1.0
Official Release

WIZ810Sio User Manual (WIZnet Co.,Ltd.)
3
Contents
1. Introduction.......................................................................... 4
1.1. Feature ........................................................................................ 4
2. Pin assignment & description ...................................................... 5
2.1. Pin assignment.............................................................................. 5
2.2. Pin description .............................................................................. 6
3. Device SPI operations ................................................................ 7
3.1. Process of using general SPI Master device ......................................... 7
3.2. Read processing ............................................................................ 8
3.3. Write processing.......................................................................... 10
4. Timing diagram....................................................................... 12
4.1. Reset Timing ............................................................................... 12
4.2. SPI Access Read Timing ................................................................ 13
4.3. SPI Access Write Timing ................................................................ 13
5. Dimensions............................................................................ 14
6. Reference Schematics........................................................... 6-15
7. Warranty ............................................................................ 7-16

WIZ810Sio User Manual (WIZnet Co.,Ltd.)
4
1. Introduction
WIZ810Sio is the internet offload network module that includes W5100S (TCP/IP
hardwired chip, include PHY), MAG-JACK (RJ45 with X’FMR) with other glue logics.
It can be used as a component and no effort is required to interface W5100S and
Transformer.
The WIZ810Sio is an ideal option for users who want to develop their Internet
enabling systems rapidly.
For the detailed information on implementation of Hardware TCP/IP, refer
to the W5100S Datasheet.
WIZ810Sio consists of W5100S and MAG-JACK.
⚫TCP/IP, Ethernet MAC : W5100S
⚫Ethernet PHY : Included in W5100S
⚫Connector : MAG-JACK(RJ45 with Transformer)
1.1. Feature
⚫Support Hardwired Internet protocols
: TCP, UDP, WOL over UDP, ICMP, IGMPv1/v2, IPv4, ARP, PPPoE
⚫Support 4 independent SOCKETs simultaneously
⚫Supports half/full duplex operation
⚫Support SOCKET-less command
: ARP-Request, PING-Request
⚫Support Ethernet Power down mode & Main Clock gating for power save
⚫Support Wake on LAN over UDP
⚫Supports high speed SPI Interface (SPI mode 0/3)
⚫Internal 16Kbytes Memory for TX/ RX Buffers
⚫10BaseT/100BaseTX Ethernet PHY Integrated
⚫Support Auto Negotiation (Full and half duplex, 10 and 100-based )
⚫Supports Wake On LAN
⚫Support Auto-MDIX only when Auto-Negotiation mode
⚫3.3V operation with 5V I/O signal tolerance
⚫Interfaces with two 2.54mm pitch 1 x 6 header pin
⚫Very small form factor: 23mm x 25mm (PCB size)

WIZ810Sio User Manual (WIZnet Co.,Ltd.)
5
2. Pin assignment & description
2.1. Pin assignment
< TOP side view >
< Pin assignment >

WIZ810Sio User Manual (WIZnet Co.,Ltd.)
6
2.2. Pin description
Pin No.
I/O
Pin Name
Description
J1
1
P
GND
Ground
2
P
GND
Ground
3
I
MOSI
SPI Master Out Slave In
This pin is used to SPI MOSI signal pin.
4
I
SCLK
SPI Clock
This pin is used to SPI Clock Signal pin.
5
I
SCSn
SPI Slave Select : Active Low
This pin is used to SPI Slave Select signal
Pin when using SPI interface.
6
O
INTn
Interrupt : Active low
This pin indicates that W5100S requires
MCU attention after socket connecting,
disconnecting, data receiving timeout, and
WOL (Wake on LAN). The interrupt is
cleared by writing IR Register or Sn_IR
(Socket n-th Interrupt Register). All
interrupts are maskable.
J2
1
P
GND
Ground
2
P
3V3D
Power : 3.3 V power supply
3
P
3V3D
Power : 3.3 V power supply
4
I
-
-
5
I
RSTn
Reset : RSTn initializes W5100S. RSTn
must be asserted to Low longer than
500ns. After asserted RSTn,
W5100S spends 60.3ms for initialization.
Low : W5100S initialized.
High : Normal Operation.
6
O
MISO
SPI Master In Slave Out
This pin is used to SPI MISO signal pin.

WIZ810Sio User Manual (WIZnet Co.,Ltd.)
7
3. Device SPI operations
WIZ810Sio is controlled by a set of instruction that is sent from an external host,
commonly referred to as the SPI Master. The SPI Master communicates with
W5100S on WIZ810Sio via the SPI bus, which is composed of four signal lines:
Slave Chip Select (SCSn), Serial Clock (SCLK), MOSI (Master Out Slave In) and
MISO (Master In Slave Out).
The SPI protocol defines four modes for its operation (Mode 0-3). Each mode
differs according to the SCLK polarity and phase - how the polarity and phase
control the flow of data on the SPI bus. The W5100S operates as SPI Slave device
and supports the most common modes - SPI Mode 0 and 3.
The only difference between SPI Mode 0 and 3 is the polarity of the SCLK signal
at the inactive state. With SPI Mode 0 and 3, data is always latched in on the
rising edge of SCLK and always output on the falling edge of SCLK.
3.1. Process of using general SPI Master device
1. Configure Input/Output direction on SPI Master Device pins.
2. Configure SCSn as ‘High’ on inactive
3. Configure SCSn as ‘Low’ (data transfer start)
4. Write Control Byte for transmission on SPDR register.
5. Write target address for transmission on SPDR register (SPI Data Register).
6. Write desired data for transmission on SPDR register.
7. Wait for reception complete
8. If all data transmission ends, configure SCSn as ‘High’
< W5100S SPI Frame Format >

WIZ810Sio User Manual (WIZnet Co.,Ltd.)
8
< Control, Address and DATA Sequence Diagram >
3.2. Read processing
The READ processing is entered by driving SCSn low, followed by the Address,
the OP code, the Data Length and the Data byte on MOSI. The OP code (OP) is
defined type of the READ OP and WIRTE OP. On OP = 0x0F, the read operation is
selected. On OP = 0xF0, the write operation is selected.
In W5100S SPI mode, the Byte READ processing and the burst READ processing
are provided. The Byte READ processing takes 3 instructions which is consist of
the 8-bit OP code(0x0F),16-bit Address and 8-bit Data. Otherwise, The Burst
READ processing only takes the Data instruction after the setting of the burst
read processing. The MISO pin should be selected by driving MISO low after the
falling edge of the SCSn.

WIZ810Sio User Manual (WIZnet Co.,Ltd.)
9
< Read Sequence >
/* Pseudo Code for Read data of 8bit per packet */
#define data_read_command 0x00
uint16 addr; // Address : 16bits
int16 data_len; // Data length :15bits
uint8 data_buf[]; // Array for data
SpiSendData(); // Send data from MCU to W5100S
SpiRecvData(); // Receive data from W5100S to MCU
{
ISR_DISABLE(); // Interrupt Service Routine disable
CSoff(); // CS=0, SPI start
// OP Read command
SpiSendData (0x0F);
// SpiSendData
SpiSendData(((addr+idx) & 0xFF00) >> 8); // Address byte 1
SpiSendData((addr+idx) & 0x00FF); // Address byte 2
// Read data:On data_len> 1, Burst Read Processing Mode.
for(int idx = 0; idx<data_len; idx++)

WIZ810Sio User Manual (WIZnet Co.,Ltd.)
10
3.3. Write processing
The WRITE processing is entered by driving SCSn low, followed by the Address,
the OP code, the Data Length, and the Data byte on MISO.
In W5100S SPI mode, the Byte WRITE processing and the Burst WRITE processing
are provided. The Byte WRITE processing takes 3 instructions which is consist of
the 8-bit OP code(0xF0), the 16-bit Address and 8-bit Data. Otherwise, The Burst
WRITE processing only takes the Data instruction after the setting of the Burst
WRITE processing. The MOSI pin should be selected by driving MOSI low after the
falling edge of the SCSn.
< Write Sequence >
{
SpiSendData(0); // Dummy data
data_buf[idx] = SpiRecvData(idx); // Read data
}
CSon(); // CS=1, SPI end
ISR_ENABLE(); // Interrupt Service Routine disable
}
/* Pseudo Code for Write data of 8bit per packet */
#define data_write_command 0x80
uint16 addr; // Address : 16bits

WIZ810Sio User Manual (WIZnet Co.,Ltd.)
11
int16 data_len; // Data length :15bits
uint8 data_buf[]; // Array for data
{
SpiSendData(); //Send data from MCU to W5100S
ISR_DISABLE();// Interrupt Service Routine disable
CSoff();// CS=0, SPI start
//OP Write command
SpiSendData(0xF0);
SpiSendData(((addr+idx) & 0xFF00) >> 8); // Address byte 1
SpiSendData((addr+idx) & 0x00FF); // Address byte 2
// Write data: On data_len> 1, Burst Write Processing Mode.
for(int idx = 0; idx<data_len; idx++)
SpiSendData(data_buf[idx]);
CSon(); // CS=1, SPI end
IINCHIP_ISR_ENABLE(); // Interrupt Service Routine disable
}

WIZ810Sio User Manual (WIZnet Co.,Ltd.)
12
4. Timing diagram
4.1. Reset Timing

WIZ810Sio User Manual (WIZnet Co.,Ltd.)
13
4.2. SPI Access Read Timing
4.3. SPI Access Write Timing

WIZ810Sio User Manual (WIZnet Co.,Ltd.)
14
5. Dimensions

WIZ810Sio User Manual (WIZnet Co.,Ltd.)
6-15
6. Reference Schematics

WIZ810Sio User Manual (WIZnet Co.,Ltd.)
7-16
7. Warranty
WIZnet Co., Ltd. offers the following limited warranties applicable only to the
original purchaser. This offer is non-transferable.
WIZnet warrants our products and its parts against defects in materials and
workmanship under normal use for period of standard ONE(1) YEAR for the
WIZ810Sio module and labor warranty after the date of original retail purchase.
During this period, WIZnet will repair or replace a defective products or part free of
charge.
Warranty Conditions:
1. The warranty applies only to products distributed by WIZnet or our official
distributors.
2. The warranty applies only to defects in material or workmanship as
mentioned above in 3.Warranty. The warranty applies only to defects which
occur during normal use and does not extend to damage to products or
parts which results from alternation, repair, modification, faulty installation
or service by anyone other than someone authorized by WIZnet ; damage
to products or parts caused by accident, abuse, or misuse, poor
maintenance, mishandling, misapplication, or used in violation of
instructions furnished by us ; damage occurring in shipment or any damage
caused by an act of God, such as lightening or line surge.
Procedure for Obtaining Warranty Service
1. Contact an authorized distributors or dealer of WIZnet for obtaining an RMA
(Return Merchandise Authorization) request form within the applicable
warranty period.
2. Send the products to the distributors or dealers together with the completed
RMA request form. All products returned for warranty must be carefully
repackaged in the original packing materials.
3. Any service issue, please contact to sal[email protected]