Wolf ICBCT15G/S User manual

GAS COOKTOPS
INSTALLATION INSTRUCTIONS
INSTRUCCIONES DE INSTALACIÓN
INSTRUCTIONS D’INSTALLATION
ISTRUZIONI PER L’INSTALLAZIONE
INSTALLATIONSANWEISUNGEN

3
EN G L I S H 4
ES P Ã N O L 1 8
F R A N Ç A I S 3 2
I TA L I A N O 4 6
D E U T S C H 6 0

As you follow these instru tions, you will
noti e WARNING and CAUTION symbols. This
blo ked information is impor tant for the safe
and effi ient installation of Wolf equipment.
There are two types of potential hazards that
may o ur during installation.
Another footnote we would like to identify is
IMPORTANT NOTE: This highlights informa-
tion that is espe ially relevant to a problem-
free installation.
signals a situation where minor injury or
produ t damage may o ur if you do not
follow instru tions.
states a hazard that may ause serious
injury or death if pre autions are not
followed.
WOLF®is a registered trademark of Wolf Appliance, Inc.
C O N TA C T
I N F O R M AT I O N
Website:
wolfapplian e. om

5
IN STA LL AT ION R E Q U I R E M E N T S
WHAT TO DO IF YOU SMELL GAS:
Do not try to light any appliance.
Do not touch any electrical switch.
Do not use any phone in your
building.
Immediately call your gas supplier
from a neighbor’s phone. Follow
the gas supplier’s instructions.
If you cannot reach your gas
supplier, call the fire department.
W O L F GA S C OO KTO PS
IMPORTANT NOTE:
Installation and service must be
performed by a qualified installer,
service agency or the gas supplier.
Do not store or use gasoline or
other flammable vapors and liquids
in the vicinity of this or any other
appliance.
The use of a gas cooking appliance
results in the production of heat and
moisture in the room in which it is
installed. Ensure that the kitchen is
well ventilated; keep natural ventila-
tion holes open or install a mechani-
cal ventilation device (mechanical
extractor hood)
Prolonged intensive use of the appli-
ance may for additional ventilation,
for example opening of a window, or
more effective ventilation, for
example increasing the level of
mechanical ventilation where
present.
This applian e shall be installed
in a ordan e with the regula-
tions in for e and only used in a
well ventilated spa e. Read the
instru tions before installing or
using this applian e.

6
IN STA LL AT ION R E Q U I R E M E N T S
IMPORTANT NOTE: This installation must
be ompleted by a qualified installer,
servi e agen y or gas supplier.
IMPORTANT NOTE:
Save these Installation
Instructions for the local inspector’s use.
Please read the entire Installation Instruc-
tions prior to installation.
Installer: please retain these instructions
for local inspector’s reference, then leave
them with the homeowner.
Homeowner: please read and keep these
instructions for future reference and be sure
to read the entire Use Care Information
prior to use.
IMPORTANT NOTE: This appliance must be
installed in accordance with local codes. The
correct voltage, frequency and amperage must
be supplied to the appliance from a dedicated,
grounded circuit which is protected by a
properly sized circuit breaker or time delay
fuse. The proper voltage, frequency, and
amperage ratings are listed on the product
rating plate.
Record the model and serial numbers before
installing the cooktop. Both numbers are listed
on the rating plate, located on the underside of
the cooktop. Refer to the illustration below.
BE FOR E YO U S TA RT
Proper installation is your responsibility.
Have a qualified technician install this
cooktop. You must also assure that electri-
cal installation is adequate and in compli-
ance with all local codes and ordinances.
Prior to installation, ensure that the local
distribution conditions (nature of the gas
and gas pressure) and the adjustment of
the appliance are compatible.
Proper gas supply connection must be
available; refer to Gas Supply Requirements
on page 12. Electrical ground is required;
see Electrical Requirements on page 13.
The adjustment conditions for this appli-
ance are stated on the label (or rating
plate). The data plate can be found on the
underside of the cooktop.
W O L F GA S C OOK TOP S
Rating plate lo ation
Location of rating
plate under cooktop
RAT I N G P L AT E
I N F O R M AT I O N
Model Number
Serial Number

7
IN STA LL AT ION I N S T R U C T I O N S
L O C AT I O N R E Q U I R E M E N T S
Illustrations on the following pages provide the
overall dimensions, countertop cut-out and
installation specifications for Wolf gas
cooktops. Maintain the following minimum
installation dimensions:
Minimum horizontal clearance from the
sides and back of the cooktop cut-out to
adjacent vertical combustible construction,
extending a minimum of 457 mm above the
countertop, is as follows: 178 mm from side
edges of cut-out for the 381 mm cooktop;
229 mm from side edges of cut-out for the
762 mm and 914 mm cooktops; 64 mm
from rear edge of cut-out.
Minimum vertical distance between the
countertop and combustible materials
above the cooktop must be 762 mm.
Maximum 330 mm depth of overhead side
cabinets directly above and within side
clearance.
IMPORTANT NOTE: When installing a ventila-
tion hood, refer to the specific requirements
of the hood for the minimum dimension to
countertop.
BE FOR E YO U S TA RT
Check the location where the cooktop will
be installed. The location should be away
from strong draft areas, such as windows,
doors and strong heating vents or fans. Do
not obstruct flow of combustion and
ventilation air.
This appliance is not connected to a
combustion products evacuation device. It
shall be installed and connected in accor-
dance with current installation regulations.
Particular attention shall be given to the
relevant requirements regarding ventilation.
SI TE P R E PA R AT I O N
C O U N T E RT O P C U T- O U T D I M E N S I O N S
IMPORTANT NOTE: Countertop opening
dimensions shown on the following pages
must be used. The dimensions shown provide
for required clearances.
These cooktops are designed to fit a standard
610 mm deep base cabinet with a 635 mm
deep countertop. Before making the counter-
top cut-out, verify that the cooktop will clear
the side walls of the base cabinet below. There
should be at least 140 mm clearance between
the countertop and any combustible surface
directly below the unit.
IMPORTANT NOTE: Do not seal the cooktop
to the countertop. It must be removed if
service is necessary.
Failure to lo ate the ooktop without the
proper learan es will result in a fire
hazard.
This ooktop is intended for indoor use.

8
IN STA LL AT ION S P E C I F I C AT I O N S
The illustrations below provide the overall
dimensions, countertop cut-out and installation
specifications for Model ICBCT15G.
For Model ICBCT15G, the gas service may be
supplied through the floor if the cooktop is not
installed above an oven. Refer to the illustration
for specifics on placement of gas and electrical.
914 mm
FLOOR TO
COUNTERTOP
762 mm min
COUNTERTOP
TO COMBUSTIBLE
MATERIALS
SEE COUNTERTOP
CUT-OUT BELOW
356 mm
CUT-OUT
WIDTH
COUNTERTOP CUT-OUT
FRONT
489 mm
CUT-OUT
DEPTH
64 mm min
178 mm TO
COMBUSTIBLE*
178 mm TO
COMBUSTIBLE*
SIDE
CABINET
330 mm
max
*Minimum clearance from cooktop cut-out to combustible materials up to 457 mm above countertop.
NOTE: Application shown allows for installation of two 381 mm modules side by side.
E
381 mm
381
mm
102 mm
457 mm min
127
mm
LOCATION OF GAS
AND ELECTRICAL
EXTENDS ON FLOOR
G
64
mm*
W O L F GA S C OOK TOP S
Overall Dimensions
381 mm
OVERALL WIDTH
533 mm
OVERALL
DEPTH
102 mm
MODEL ICBCT15G
D I M E N S I O N S
Overall Width 381 mm
Overall Height 102 mm
Overall Depth 533 mm
Recommended
Cabinet Width 838 mm
Minimum Cabinet Depth 578 mm
Minimum Height Clearance 102 mm
Cut-Out Width 356 mm
Cut-Out Depth 489 mm
Unit dimensions may vary to 3 mm.
I N S TA L L AT I O N S P E C I F I C AT I O N S – M O D E L I C B C T 1 5 G
IMPORTANT NOTE: When multiple cooktop
units are installed side by side, refer to the
countertop cut-out dimensions on page 11.

457 mm min
914 mm
FLOOR TO
COUNTERTOP
762 mm min
COUNTERTOP
TO COMBUSTIBLE
MATERIALS
762 mm OVEN OPENING
102 mm
254 mm
89 mm E
SEE COUNTERTOP
CUT-OUT BELOW
229 mm TO
COMBUSTIBLE*
229 mm TO
COMBUSTIBLE*
64
mm*
SIDE
CABINET
330 mm
max
737 mm
CUT-OUT WIDTH
COUNTERTOP CUT-OUT
FRONT
489 mm
CUT-OUT
DEPTH
64 mm min
*Minimum clearance from cooktop cut-out to combustible materials up to 457 mm above countertop.
NOTE: Gas and electrical location applies only to installation with built-in oven.
G
9
IN STA LL AT ION I N S T R U C T I O N S
Overall Dimensions
533 mm
FONDO
TOTAL
762 mm
ANCHURA TOTAL
102 mm
IN STA LL AT ION S P E C I F I C AT I O N S
The illustrations below provide the overall
dimensions, countertop cut-out and installation
specifications for Model ICBCT30G.
IMPORTANT NOTE: 838 mm wide cabinets are
recommended for installation of Model
ICBCT30G.
A Wolf 762 mm single built-in oven may be
installed below Model ICBCT30G. For this
installation, unless you are using cabinets
deeper than 610 mm, it is recommended that
the electrical and gas supply be placed in the
base cabinet to the right of the oven. Refer to
installation instructions provided with the built-
in oven for additional specifications.
If the Model ICBCT30G is installed above
cabinets, the gas and electrical placement is not
critical. A grounded outlet needs to be placed
within 1.2 m of the right rear of the cooktop.
IMPORTANT NOTE: When multiple cooktop
units are installed side by side, refer to the
countertop cut-out dimensions on page 11.
MODEL ICBCT30G
D I M E N S I O N S
Overall Width 762 mm
Overall Height 102 mm
Overall Depth 533 mm
Recommended
Cabinet Width 838 mm
Minimum Cabinet Depth 578 mm
Minimum Height Clearance 102 mm
Cut-Out Width 737 mm
Cut-Out Depth 489 mm
Unit dimensions may vary to 3 mm.
I N S TA L L AT I O N S P E C I F I C AT I O N S – M O D E L I C B C T 3 0 G

10
W O L F GA S C OOK TOP S
IN STA LL AT ION S P E C I F I C AT I O N S
The illustrations below provide the overall
dimensions, countertop cut-out and installation
specifications for Model ICBCT36G.
IMPORTANT NOTE: 991 mm wide cabinets are
recommended for installation of Model
ICBCT36G.
A Wolf 914 mm built-in oven may be installed
below Model ICBCT36G. For this installation,
unless you are using cabinets deeper than 610
mm, it is recommended that the electrical and
gas supply be placed in the base cabinet to the
right of the oven. Refer to installation instruc-
tions provided with the built-in oven for addi-
tional specifications.
If the Model ICBCT36G is installed above
cabinets, the gas and electrical placement is not
critical. A grounded outlet needs to be placed
within 1.2 m of the right rear of the cooktop.
When a 914 mm built-in oven is installed below
Model ICBCT36G, it is recommended that the
rough opening for the oven be 197 mm from
the floor to ease the use of the oven door.
IMPORTANT NOTE: When multiple cooktop
units are installed side by side, refer to the
countertop cut-out dimensions on page 11.
102 mm
E
G
457 mm min
914 mm
FLOOR TO
COUNTERTOP
762 mm min
COUNTERTOP
TO COMBUSTIBLE
MATERIALS
914 mm OVEN OPENING
254 mm
89 mm
SEE COUNTERTOP
CUT-OUT BELOW
889 mm
CUT-OUT WIDTH
COUNTERTOP CUT-OUT
FRONT
489 mm
CUT-OUT
DEPTH
64 mm min
229 mm TO
COMBUSTIBLE*
229 mm TO
COMBUSTIBLE*
SIDE
CABINET
330 mm
max
*Minimum clearance from cooktop cut-out to combustible materials up to 457 mm above countertop.
NOTE: Gas and electrical location applies only to installation with built-in oven.
64
mm*
Overall Dimensions
533 mm
OVERALL
DEPTH
914 mm
OVERALL WIDTH
102 mm
MODEL ICBCT36G
D I M E N S I O N S
Overall Width 914 mm
Overall Height 102 mm
Overall Depth 533 mm
Recommended
Cabinet Width 991 mm
Minimum Cabinet Depth 578 mm
Minimum Height Clearance 102 mm
Cut-Out Width 889 mm
Cut-Out Depth 489 mm
Unit dimensions may vary to 3 mm.
I N S TA L L AT I O N S P E C I F I C AT I O N S – M O D E L I C B C T 3 6 G

11
IN STA LL AT ION I N S T R U C T I O N S
IN STA LL AT ION O P T I O N S
M U LT I P L E C O O K T O P I N S TA L L AT I O N
If the gas cooktop is to be used with any
combination of additional cooktop units or
modules with a filler strip, the cut-out width is
calculated by adding the corresponding units'
cut-out dimensions plus 32 mm for each addi-
tional unit. Refer to the illustration below.
IMPORTANT NOTE: When multiple units are
installed side by side, each unit must have its
own separate recommended electrical circuit.
When two or more modules are installed
together, an integrated module filler strip
(IFILLER/S) is recommended. Contact your
Wolf dealer for information on these accessory
components.
64 mm
min
FRONT OF COUNTERTOP
489 mm
CUT-OUT
DEPTH
743 mm
TWO MODULES WIDTH
1130 mm – THREE MODULES WIDTH OR
1124 mm – 762 mm COOKTOP AND ONE MODULE
1518 mm – FOUR MODULES WIDTH OR
1511 mm – 762 mm COOKTOP AND TWO MODULES OR
1276 mm – 914 mm COOKTOP AND ONE MODULE
356 mm
CUT-OUT
WIDTH
Countertop ut-out dimensions for installation of multiple ooktops
OP T I O N A L
I N S TA L L AT I O N S
Dimensions will
vary a ording to
the spe ifi installa-
tion.

12
W O L F GA S C OOK TOP S
IMPORTANT NOTE: The gas cooktop must be
connected to a regulated gas supply.
IMPORTANT NOTE: This installation must
conform with local codes and ordinances.
IMPORTANT NOTE: The natural gas cooktop
is rated for elevations up to 2438 m without
adjustment. Install a high altitude kit for eleva-
tions from 2438 to 3084 m. The LP gas cooktop
is rated for 3084 m.
The rating plate, located on the underside of
the burner box, has information on the type of
gas that should be used. If this information
does not agree with the type of gas available,
check with the local gas supplier.
EXPLOSION HAZARD—
Se urely tighten all external gas
onne tions.
Failure to do so an result in explosion,
fire or death.
GAS SUPPLY R E Q U I R E M E N T S
Provide a gas supply line of 19 mm rigid pipe
to the cooktop location. A smaller size pipe on
long runs may result in insufficient gas supply.
Pipe joint compounds, suitable for use with LP
gas should be used. For LP gas, piping or
tubing size can be 13 mm minimum. LP gas
suppliers usually determine the size and mate-
rials used on the system.
If local codes permit, a flexible metal appliance
connector is recommended for connecting this
cooktop to the gas supply line. Do not kink or
damage the flexible connector when moving
the cooktop. You will need to determine the
fittings required, depending on the size of your
gas supply line, flexible metal connector and
shut-off valve.
If rigid pipe is used as a gas supply line, a
combination of pipe fittings must be used to
obtain an in-line connection to the cooktop. All
strains must be removed from the supply and
gas lines so the cooktop will be level and in
line.
IM P O RTA N T
N OT E
This installation
must onform with
lo al odes and
ordinan es.
GA S R AT I N G
Total Heat Ele tri al Types and
Output Gas Rating Applian e Pressures
Model # (Gas) Units (Watts) Category (mbar) Country of Destination
I2H G20 at 20 AT, DK, EE, FI, GR, IE, IT, LT,
ICBCT15G/S 6.8 kW 230 NO, PT, ES, SE, SI, SK, GB, CH
I2E G20 at 20 DE, PL
I2E+ G20 at 20/25 BE, FR
ICBCT15G/S-LP 494 g/h 230 I3P G31 at 37 BE, CZ, FR, GR, IE, NL, NO, PT,
ES, GB, CH
I2H G20 at 20 AT, DK, EE, FI, GR, IE, IT, LT,
ICBCT30G/S 14.7 kW 230 NO, PT, ES, SE, SI, SK, GB, CH
I2E G20 at 20 DE, PL
I2E+ G20 at 20/25 BE, FR
ICBCT30G/S-LP 1069 g/h 230 I3P G31 at 37 BE, CZ, FR, GR, IE, NL, NO, PT,
ES, GB, CH
I2H G20 at 20 AT, DK, EE, FI, GR, IE, IT, LT,
ICBCT36G/S 17.7 kW 230 NO, PT, ES, SE, SI, SK, GB, CH
I2E G20 at 20 DE, PL
I2E+ G20 at 20/25 BE, FR
ICBCT36G/S-LP 1287 g/h 230 I3P G31 at 37 BE, CZ, FR, GR, IE, NL, NO, PT,
ES, GB, CH

13
IN STA LL AT ION I N S T R U C T I O N S
EL ECT RI CA L R E Q U I R E M E N T S
ELECTRICAL SHOCK HAZARD—
Plug into a grounded 3-prong adapter.
Do not remove ground prong.
Do not use an adapter.
Failure to follow these instru tions an
result in ele tri sho k, fire or death.
IMPORTANT NOTE: Connection of this appli-
ance should be through a fused connection
unit or a suitable isolator, which complies with
national and local safety regulations. The
on/off switch should be easily accessible after
the appliance has been installed. If the switch
is not accessible after installation (depending
on country) an additional means of disconnec-
tion must be provided for all poles of the
power supply. When switched off there must
be an all pole contact gap of 3 mm in the
isolator switch. This 3 mm contact disconnect
gap must apply to any isolator switch, fuses
and/or relays according to EN60335.
R E C O M M E N D E D G R O U N D M E T H O D
IMPORTANT NOTE: For your personal safety,
this cooktop must be grounded. This cooktop
is equipped with a 3-prong ground plug. To
minimize possible shock hazard, a 85C
minimum rated cord must be plugged into a
mating 3-prong ground-type outlet, grounded
in conformance with all local codes and ordi-
nances. If a mating outlet is not available, it is
the obligation of the customer to have a
properly grounded, 3-prong outlet installed by
a qualified electrician.
IMPORTANT NOTE: If product is connected to
a GFCI protected outlet, nuisance tripping of
power supply may occur, resulting in loss of
product operation.
W I R I N G D I A G R A M
A wiring diagram covering the control circuit
for each Wolf gas cooktop model can be found
on page 17.
IMPORTANT NOTE: If codes permit and a
separate ground wire is used, it is recom-
mended that a qualified electrician determine
that the ground path is adequate.
IMPORTANT NOTE: Check with a qualified
electrician if you are not sure whether the
cooktop is properly grounded.
IMPORTANT NOTE: Do not ground to a gas
pipe.
A 220-240 V AC, 50/60 Hz, fused electrical
supply is required. A time-delay fuse or circuit
breaker is recommended. It is recommended
that a separate circuit serving only this appli-
ance be provided.
Electronic ignition systems operate within
wide voltage limits, but proper ground and
polarity are necessary. In addition to checking
that the outlet provides 220-240 V AC power
and is correctly grounded, the outlet must be
checked by a qualified electrician to see if it is
wired with correct polarity. A wiring diagram is
provided in the literature package.
This appliance, when installed, must be electri-
cally grounded in accordance with local codes.

14
C O O K T O P IN STA LL ATI ON
Remove the cooktop, burner grates and burner
caps from the shipping package.
Lower the cooktop into the countertop cut-out
opening. Center the cooktop in the opening
and check that the front edge of cooktop is
parallel to the front edge of the countertop.
Check that all required clearances are met. Use
a pencil to outline the rear edge of the cooktop
on the countertop. Remove the cooktop from
the countertop opening.
IMPORTANT NOTE: When repositioning the
cooktop in the countertop cut-out opening, lift
the entire cooktop up from the opening to
prevent scratching the countertop.
Remove the foam strip from the hardware
package. Apply the foam strip around the
bottom of the burner box flush with the edge
as shown in the illustration below.
Reinsert the cooktop into the countertop
opening. Check that the cooktop is parallel to
the front edge of the countertop. Lift the entire
cooktop to make adjustments and align the
rear edge with the pencil line.
Attach the brackets to the burner box. Insert
the 89 mm clamping screws into the brackets.
Use a screwdriver to tighten the clamping
screws against the underside of the counter-
top. Refer to the illustration below. Do not
overtighten screws.
G A S L E A K T E S T I N G
Use a brush and liquid detergent to test all gas
connections for leaks. Bubbles around connec-
tions will indicate a leak. If a leak appears, shut
off gas valve controls and adjust connections.
Then check connections again. Clean all the
detergent solution from the cooktop.
Cooktop
Burner Box Foam Strip
Foam strip appli ation
W O L F GA S C OOK TOP S
89 mm
Clamping
Screw
Burner Box
Countertop
Bracket
Screws
Bracket
Bra ket installation
Never test for a gas leak with a mat h or
other flame.

15
IN STA LL AT ION I N S T R U C T I O N S
SU RFACE B U R N E R S
I N I T I A L L I G H T I N G
The surface burners use electronic igniters in
place of standing pilots. When the cooktop
control knob is pushed in and turned to the
position, the system creates a spark to
light the burner. This sparking continues until
the electronic ignition senses a flame. If the
burner fails to ignite after 10 seconds, return
the knob to the position and attempt to
ignite by turning the knob back to the
position.
Be sure to place the burner heads and caps on
each burner base and position the burner
grates over the burner bases and heads before
lighting.
To check operation of the surface burners,
push in and turn each control knob to the
position. The flame should light within four
seconds.
If the burners do not light properly, turn
control knob to the position. Check that
the burner heads and caps are in the proper
position. Check that the power supply cord is
plugged in and that the circuit breaker or
house fuse has not blown. Check operation
again, if the burners do not light properly at
this point, contact a Wolf authorized service
center.
IMPORTANT NOTE: Initial lighting of the
surface burners may take slightly longer, as air
in the system must be purged before gas can
be supplied to the burner.
CO OKTOP R E M O A L
If it is necessary to remove the cooktop for
cleaning or service, shut off the gas supply.
Disconnect the gas and electric supply.
Remove the mounting brackets on the right
and left side of the burner box and remove the
cooktop. Reinstall in the reverse order and
check the gas connection for leaks.
TROUBLES H O OT I N G
IMPORTANT NOTE: If the cooktop does not
operate properly, follow these troubleshooting
steps:
Verify that power is being supplied to the
cooktop.
Check that gas valves are turned to the ON
position.
Check the gas supply and electrical
connections to ensure that the installation
has been completed correctly.
Follow troubleshooting procedures as
described in the Wolf Gas Cooktops
Use Care Information.
If the cooktop still does not work, contact
a Wolf authorized service center. Do not
attempt to repair the cooktop yourself. Wolf
is not responsible for service required to
correct a faulty installation.

16
C O N TA C T
I N F O R M AT I O N
Website:
wolfapplian e. om
W O L F GA S C OOK TOP S
I F YO U N E E D SE RVI CE
For service in your area, contact either your
Wolf dealer or visit the Showroom Locator
section of our website, wolfappliance.com
to find the regional distributor by country.
When calling for service, you will need the
cooktop model and serial numbers. Both
numbers are listed on the rating plate,
located on the underside of the cooktop.
Refer to the illustration on page 6 for
location of the rating plate.
The information and images in this book are the
opyright property of Wolf Applian e, In ., an affili-
ate of Sub-Zero, In . Neither this book nor any
information or images ontained herein may be
opied or used in whole or in part without the
express written permission of Wolf Applian e,
In .,an affiliate of Sub-Zero, In .
©Wolf Applian e, In . all rights reserved.

17
IN STA LL AT ION I N S T R U C T I O N S
POWER CORD
FRONT
RIV
GAS VALVE
RED
RED
BLACK
WHITE
GRN/YEL
BLACK
REAR
BLACK
BLACK
WHITE
WHITE
Model ICBCT15G
POWER CORD
WHITE
RIGHT
FRONT
BLACK
RIV
GAS VALVE
RED RED
RED
RED
WHITE
GRN/YEL
BLACK
RIGHT
REAR
LEFT
REAR
LEFT FRONT
BLACK
WHITE
WHITE
BLACK
LEFT FRONT
POWER CORD
RED
RIV
GAS VALVE
WHITE
BLACK
RIGHT
REAR
LEFT REAR
RIGHT
FRONT
CTR REAR
GRN/YEL
BLACK
RED RED
RED
BLACK
WHITE
WI RIN G D I A G R A M S
Model ICBCT30G
Model ICBCT36G

Cuando onsulte las instru iones que apare en en
esta guía, en ontrará símbolos de ADVERTENCIA y
PRECAUCIÓN. Esta informa ión en re uadros es
importante para instalar el equipo de Wolf de forma
segura y efi az. Existen dos tipos de posibles riesgos
que pueden produ irse durante una instala ión.
Otro tipo de anota ión que es importante resaltar es
la que se in luye en NOTA IMPORTANTE: En esta
nota se resalta la informa ión que resulta espe ial-
mente importante para que la instala ión se reali e
sin problemas.
PRECAUCIÓN
indi a una situa ión en la que se pueden sufrir
heridas leves o provo ar daños se undarios al
produ to si no se siguen las instru iones.
indi a peligro de que se produz an heridas
personales graves o in luso puede provo ar
la muerte si no se siguen las pre au iones
espe ifi adas.
WOLF®es una marca comercial registrada de Wolf Appliance, Inc.
I N F O R M A C I Ó N
D E C O N TA C T O
Página Web:
www.sub-
zero.eu. om

19
R E Q U I S I T O S D E INS TA LAC I Ó N
QUÉ SE DEBE HACER SI HUELE A GAS:
No encienda ningún aparato.
No toque ningún interruptor eléctrico.
No utilice ningún teléfono dentro
del edificio.
Llame inmediatamente a su proveedor
de gas desde el teléfono de un vecino.
Siga las instrucciones que le propor-
cione el proveedor de gas.
Si no le es posible ponerse en
contacto con el proveedor de gas,
llame a los bomberos.
PLACAS DE GAS D E W O L F
NOTA IMPORTANTE:
La instalación y el mantenimiento
deben ser realizados por un insta-lador
cualificado, por un centro de asistencia
técnica o por el proveedor de gas.
No almacene ni utilice gasolina ni otros
vapores ni líquidos infla-mables cerca
de éste o de otros aparatos.
La utilización de un aparato de cocción
de gas produce calor y vaho en la
habitación en la que está instalado.
Asegúrese que la cocina está bien venti-
lada; mantenga despejados los agujeros
de ventilación natural o instale un
dispositivo de ventilación mecánico
(campana extractora mecánica).
Si utiliza mucho el aparato y lo hace de
manera prolongada, es posible que
necesite ventilación adicional, por
ejemplo, puede abrir una ventana, o si
quiere que la ventilación sea más eficaz,
aumente el nivel de la ventilación
mecánica, si dispone de ella.
Este aparato debe instalarse de
a uerdo on las normativas vigentes
y sólo puede ser utilizado en un
lugar que esté bien ventilado. Lea las
instru iones antes de instalar o
utilizar este aparato.

20
R E Q U I S I T O S D E INS TA LAC I Ó N
NOTA IMPORTANTE: Esta instala ión debe ser
realizada por un instalador ualifi ado, por un
entro de asisten ia té ni a o por el proveedor
de gas.
NOTA IMPORTANTE: Guarde estas instrucciones
de instalación para que el inspector local pueda
utilizarlas.
Lea las instrucciones de instalación antes de
llevar a cabo la instalación.
Instalador: guarde estas instrucciones para que
el inspector local pueda utilizarlas como referen-
cia y, a continuación, entréguelas el propietario
del aparato.
Propietario: lea y guarde estas instrucciones
para que pueda utilizarlas como referencia en el
futuro y asegúrese de leer la guía de uso y
manteni-miento antes de utilizar el aparato.
NOTA IMPORTANTE: Este aparato debe instalarse
siguiendo las normativas nacionales correspondi-
entes. Se debe aplicar al aparato el voltaje, la
frecuencia y el amperaje adecuados desde una insta-
lación eléctrica resistente con toma de tierra prote-
gida por un fusible de retardo. El voltaje, la frecuen-
cia y el amperaje se muestran en la placa de datos
del producto.
Apunte la referencia del modelo y el número de
serie antes de instalar el aparato. Esta información
se muestra en la placa de datos del producto situada
en la parte inferior de la placa. Observe la siguiente
ilustración.
ANTES D E C O M E N Z A R
Es responsabilidad del propietario asegurarse de
que la instalación se realiza de manera correcta.
Esta placa debe ser instalada por un técnico cuali-
ficado. Debe asegurarse de que la instalación
eléctrica es la correcta y que cumple todos los
códigos y normativas nacionales.
Antes de llevar a cabo la instalación, asegúrese
de que las condiciones de distribución locales
(tipo y presión del gas) y el ajuste del aparato
son compatibles.
Debe disponer de una entrada de suministro de
gas; consulte la sección Requisitos del suministro
de gas en la página 26. También debe disponer de
una conexión eléctrica a tierra; consulte la sección
Requisitos eléctricos en la página 27.
Las condiciones de ajuste de este aparato se
especifican en la etiqueta (o en la placa de datos
del producto). La placa de datos está ubicada en
la parte inferior del aparato.
PLACAS DE GAS D E W O L F
Ubi a ión de la pla a de datos
Ubicación de la placa
de datos debajo
de la placa
I N F O R M A C I Ó N
D E L A P L A C A
D E D ATO S
Referen ia del
modelo
Número de serie