Wolf ICBGC152T/S User manual

GAS COOKTOP
INSTALLATION GUIDE

2 | English
GAS COOKTOP
Contents
2Gas Cooktop
3Specications
5Installation
5Troubleshooting
Features and specications are subject to change at any
time without notice. Visit wolfappliance.com/specs for the
most up-to-date information.
Product Information
Important product information including the model and
serial number are listed on the product rating plate. The
rating plate is located on the bottom of the cooktop. Refer
to the illustration below.
If service is necessary, contact Wolf factory certied service
with the model and serial number.
Important Note
To ensure this product is installed and operated as safely
and efciently as possible, take note of the following types
of highlighted information throughout this guide:
IMPORTANT NOTE highlights information that is especially
important.
CAUTION indicates a situation where minor injury or product
damage may occur if instructions are not followed.
WARNING states a hazard that may cause serious injury or
death if precautions are not followed.
IMPORTANT NOTE: Save these instructions for the local
electrical inspector.
WARNING
This appliance shall be installed in accordance with the
regulations in force and only used in a well ventilated
space. Read the instructions before installing or using
this appliance.
WARNING
FOR AUSTRALIA ONLY:
•Do not use or store ammable materials in the
appliance storage drawer or near this appliance.
•Do not spray aerosols in the vicinity of this appli-
ance while in operation.
•Do not modify this appliance.
•This appliance is for indoor use only.
•A ventilation unit is suggested for use with this
appliance. Refer to the instructions shipped with the
ventilation unit for proper clearances.
•If the information in the guide is not followed, a re
or explosion may result, causing property damage,
personal injury or death.
•This appliance must be properly installed and
serviced by a qualied installer, service agency or
gas supplier and grounded (earthed) by a qualied
technician.
Rating plate location.
RATING PLATE
Installation Requirements
If a cooktop is being installed above an oven, a minimum
of 6 mm is required between units. A minimum 140 mm is
required from the bottom of the cooktop to combustible
materials.
Electrical
Installation must comply with all applicable electrical codes.
Locate the electrical supply as shown in the illustrations
on page 4. A separate circuit, servicing only this appliance
is required. A ground fault circuit interrupter (GFCI) is not
recommended and may cause interruption of operation.
ELECTRICAL REQUIREMENTS
Electrical Supply grounded (earthed)
220-240 V AC, 50/60 Hz
Service 10 amp dedicated circuit
Receptacle grounding-type (earthed)
IMPORTANT NOTE: Connection of this appliance should be
through a fused connection unit or a suitable isolator, which
complies with national and local safety regulations. The
on/off switch should be easily accessible after the appli-
ance has been installed. If the switch is not accessible after
installation (depending on country) an additional means of
disconnection must be provided for all poles of the power
supply. When switched off there must be an all pole contact
gap of 3 mm in the isolator switch. This 3 mm contact dis-
connect gap must apply to any isolator switch, fuses and/or
relays according to EN60335.
WARNING
FOR AUSTRALIA ONLY:
This appliance is supplied with a cord and can be hard
wired to a terminal box or plug. Do not remove the
ground (earthed) plug.
P (BROWN)
N (BLUE)
E (GREEN/YELLOW)

subzero-wolf.com.au | 3
SPECIFICATIONS
Gas Supply
Installation must conform with local codes and ordinances.
Locate the gas supply as shown in the illustrations on
page 4.
The cooktop is equipped for use with natural or liquid pro-
pane (LP) gas. The product rating plate has information on
the type of gas that should be used. For rating plate loca-
tion, refer to the illustration below. If this information does
not agree with the type of gas available, check with the local
gas supplier.
Prior to installation, ensure that the local distribution condi-
tions (nature of the gas and gas pressure) and the adjust-
ment of the appliance are compatible. The adjustment
conditions for this appliance are stated on the label (or
rating plate). The data plate can be found on the underside
of the cooktop.
This appliance is not connected to a combustion prod-
ucts evacuation device. It shall be installed and connected
in accordance with current installation regulations. Par-
ticular attention shall be given to the relevant requirements
regarding ventilation.
The cooktop must be connected to a regulated gas supply.
The supply line must be equipped with an approved external
gas shut-off valve located near the cooktop in an accessible
location. Do not block access to the shut-off valve. Refer to
the illustration below.
GAS SUPPLY REQUIREMENTS
NATURAL GAS
Gas Supply Pressure 12.5 mb
Min Line Pressure 17.5 mb
Max Pressure to Regulator 100 mb
LP GAS
Gas Supply Pressure 25 mb
Min Line Pressure 27.4 mb
Max Pressure to Regulator 100 mb
GAS RATING
MODEL
TOTAL HEAT
OUTPUT
GAS
UNITS
APPLIANCE
CATEGORY
TYPES AND
PRESSURE (mbar) COUNTRY OF DESTINATION
ICBGC152T/S 6.2 kW
I2H G20 at 20 AT, CZ, DK, FI, GR, HR, IS, IE, IT, PT, SK, SI, ES, SE, CH,
TR, GB, EE, LV, LT, NO, RO
I2E G20 at 20 DE, LU
I2E+ G20 at 20/25 BE, FR
ICBCG152T/S/LP 6.2 (443) kW (g/h) I3P G31 at 37 CH, CZ, DE, IT, ES, FI, GR, GB, NL, SK, IE, SI, RO, PL,
LV, LT
ICBCG304T/S 14.2 kW
I2H G20 at 20 AT, CZ, DK, FI, GR, HR, IS, IE, IT, PT, SK, SI, ES, SE, CH,
TR, GB, EE, LV, LT, NO, RO
I2E G20 at 20 DE, LU
I2E+ G20 at 20/25 BE, FR
ICBCG304T/S/LP 14.2 (1014) kW (g/h) I3P G31 at 37 CH, CZ, DE, IT, ES, FI, GR, GB, NL, SK, IE, SI, RO, PL,
LV, LT
ICBCG304P/S 14.2 kW
I2H G20 at 20 AT, CZ, DK, FI, GR, HR, IS, IE, IT, PT, SK, SI, ES, SE, CH,
TR, GB, EE, LV, LT, NO, RO
I2E G20 at 20 DE, LU
I2E+ G20 at 20/25 BE, FR
ICBCG304P/S/LP 14.2 (1014) kW (g/h) I3P G31 at 37 CH, CZ, DE, IT, ES, FI, GR, GB, NL, SK, IE, SI, RO, PL,
LV, LT
ICBCG365T/S 16.9 kW
I2H G20 at 20 AT, CZ, DK, FI, GR, HR, IS, IE, IT, PT, SK, SI, ES, SE, CH,
TR, GB, EE, LV, LT, NO, RO
I2E G20 at 20 DE, LU
I2E+ G20 at 20/25 BE, FR
ICBCG365T/S/LP 16.9 (1207) kW (g/h) I3P G31 at 37 CH, CZ, DE, IT, ES, FI, GR, GB, NL, SK, IE, SI, RO, PL,
LV, LT
ICBCG365P/S 16.9 kW
I2H G20 at 20 AT, CZ, DK, FI, GR, HR, IS, IE, IT, PT, SK, SI, ES, SE, CH,
TR, GB, EE, LV, LT, NO, RO
I2E G20 at 20 DE, LU
I2E+ G20 at 20/25 BE, FR
ICBCG365P/S/LP 16.9 (1207) kW (g/h) I3P G31 at 37 CH, CZ, DE, IT, ES, FI, GR, GB, NL, SK, IE, SI, RO, PL,
LV, LT
A gas supply line of 19 mm rigid pipe must be provided to
the cooktop. If local codes permit, a certied, .9 m long,
13 mm or 19 mm ID exible metal appliance connector is
recommended to connect the units 1/2" NPT (or ISO 7/1-14)
male inlet to the gas supply line. Pipe joint compounds, suit-
able for use with natural or LP gas should be used.
The appliance and its shut-off valve must be disconnected
from the gas supply piping system during any pressure
testing of the system at test pressures in excess of 100
mbar. The appliance must be isolated from the gas supply
piping system by closing its individual manual shut-off valve
during any pressure testing of the system at test pressures
equal to or less than 100 mbar.
Wolf natural gas cooktops will function up to 3124 m in
altitude without adjustment and LP gas cooktops will func-
tion up to 2621 m. If the installation exceeds these eleva-
tions, contact your authorized Wolf dealer for a high altitude
conversion kit.
WARNING
FOR AUSTRALIA ONLY:
•The appliance must be connected to a regulated
gas supply with an approved regulator.
•This appliance can be installed using a 10 mm
diam-eter 1000 mm flexible hose assembly
complying with AS/NZS 1869, Class ‘B. Maximum
working pressure 14 kPa, ambient temperature: -20°
C to 125°C and AGA approved. The hose is not
provided with the appliance.
•If installing with a flexible hose, verify the hose is not
kinked or can be damaged. If installing above and
oven, use a hose that will not be damaged by the
heat from the oven.
•Failure to locate this appliance without proper clear-
ances will result in a fire hazard.
•Model ICBCG152TF/S has an internal regulator that has
TPP of 1kPa for Natural Gas and 2.5kPa for LPG
commissioning should be completed with both burners on
higb.
SHUT-OFF VALVE
OPEN POSITION
GAS SUPPLYTO APPLIANCE
Rating plate location. Gas shut-off valve.
RATING PLATE
GAS RATING—AUSTRALIA ONLY
MODEL GAS TYPE GAS PRESSURE MJ/h ULTRA RAPID RAPID SEMI RAPID
ICBCG152TF/S Natural 1.0 kPa 24.5 N/A 1.80 / 0.65 mm 1.60/0.65mm
LP 2.75 kPa 23.5 N/A 1.06/ 0.47 mm 0.93 / 0.41 mm
ICBCG304 Natural 1.0 kPa 47.3 2.05 / .79 mm 1.59 / .65 mm 1.40 / .65 mm
LP 2.75 kPa 47.8 1.18 / .47 mm .94 / .47 mm .82 / .41 mm
ICBCG365 Natural 1.0 kPa 56.4 2.05 / .79 mm 1.59 / .65 mm 1.40 / .65 mm
LP 2.75 kPa 56.9 1.18 / .47 mm .94 / .47 mm .82 / .41 mm
Note - ICBCG152 TF/S has an on board regulator which regulates the operating pressure for Natural Gas @ 1kPa and Propane (LPG) @ 2.5kPa.
Commisioning Proceedure is with both burners set to maximum.
Not applicable for Australia

4 | English
SPECIFICATIONS
762 mm and 914 mm Gas Cooktop
STANDARD INSTALLATION
254 mm
102 mm
89 mm
FRONT VIEW
SIDE
VIEW
COUNTERTOP CUT-OUT
NOTE: Shaded area above countertop indicates minimum clearance to combustible surfaces,
combustible materials cannot be located within this area.
Electrical and gas supply location only applies to installations with built-inoven.
The height from the benchtop to the top of the trivert (Pan Support) is 34mm.
650 mm
W
WIDTH
330 mm
457 mm
229
mm
495 mm
64 mm
64 mm
E G
CUT-OUT WIDTH
MODEL W
762 mm Cooktop 737 mm
914 mm Cooktop 889 mm
FRONT VIEWSIDE VIEW
COUNTERTOP CUT-OUT
NOTE: Shaded area above countertop indicates minimum clearance to combustible surfaces,
combustible materials cannot be located within this area.
330 mm
457 mm
178
mm
E G
127
mm
ELECTRICAL
AND GAS FLOOR
LOCATION
650 mm
356 mm 495 mm
64 mm
64 mm
381 mm Gas Cooktop
STANDARD INSTALLATION

subzero-wolf.com.au | 5
Sub-Zero, Sub-Zero & Design, Sub-Zero & Snowake Design, Dual Refrigeration, The Living Kitchen, Great American Kitchens The Fine Art of Kitchen Design, Wolf, Wolf & Design, Wolf Gourmet, W & Design, red colored knobs, Cove, and Cove & Design, are registered trademarks and service marks of Sub-Zero Group, Inc. and its subsidiaries.
All other trademarks are property of their respective owners in the United States and other countries.
Cooktop Installation
Remove cooktop and components from the shipping
package and recycle packing materials.
Lower the cooktop into the countertop cut-out. Center
cooktop in the opening with the front edge aligned parallel
to the front edge of the countertop. Using a pencil, outline
the rear edge of the cooktop on the countertop. Remove
cooktop.
Apply the foam strip provided, to the perimeter of the coun-
tertop opening. Refer to the illustration below. Do not seal
the cooktop to the countertop.
Insert the cooktop into the opening. Verify the cooktop is
aligned with the front edge of the countertop.
Attach the brackets provided, to the bottom of the unit.
Insert the 89 mm clamping screws into the brackets. Use a
screwdriver to tighten clamping screws against the bottom
of the countertop. Do not overtighten screws. Refer to the
illustration below.
INSTALLATION
Gas Supply Connection
All connections to the gas piping must be wrench-tightened.
Do not overtighten or allow pipes to turn when tightening.
If a exible metal connector is being used, verify it is not
kinked, then attach the gas supply line to the regulator on
the cooktop. Open the valve and check for leaks by placing
a liquid detergent solution onto all gas connections. Bubbles
around connections indicate a gas leak. If a leak appears,
close the shut-off valve and adjust connections.
Troubleshooting
IMPORTANT NOTE: If the cooktop does not operate prop-
erly, follow these troubleshooting steps:
•Verify electrical power is supplied to the cooktop.
•Verify the gas supply shut-off valve is in the open
position.
•If the cooktop does not operate properly, contact Wolf
factory certied service. Do not attempt to repair the
cooktop. Wolf is not responsible for service required to
correct a faulty installation.
FOAM STRIP
COUNTERTOP
BRACKET CLAMPING
SCREW
Cooktop installation.

WOLF APPLIANCE, INC. P.O. BOX 44848 MADISON, WI 53744 WOLFAPPLIANCE.COM 800.222.7820
9012993 REV-A 10/2017MF089