Wood Stone TANDOOR 31 User manual

Toll Free 800.988.8103
Tel [phone]
Fax [phone]
www.woodstone-corp.com
WOOD STONE CORPORATION
1801 W. Bakerview Rd.
Bellingham, WA 98226 USA
TANDOOR
Speciality Ovens
Gas-Fired, Round, Square, Octagonal,
Barrel Models
TANDOOR 31" WS-GFT-31
TANDOOR 35" WS-GFT-35
BARREL TANDOOR WS-GFT-35-CUS
DOC NO M0053.05 REVISED April 2017
Installation and
Operation Manual

Tandoor Installation
and Operation Manual
PG 2 OF 16
M0053.05 APRIL 2017
An ongoing program of product improvement may
require us to change specifications without notice.
WOOD STONE CORPORATION
1801 W. Bakerview Rd.
Bellingham, WA 98226 USA
TOLL FREE 800.988.8103
TEL [phone]
FAX [phone]
E-MAIL [e-mail]
woodstone-corp.com
TABLE OF CONTENTS
TABLE OF CONTENTS
TANDOOR � � � � � � � � � � � � � � � � � � � � � � � � � �3
CAUTIONS AND WARNINGS � � � � � � � � � � � � �4
GFT-31 SPECIFICATIONS � � � � � � � � � � � � � � �5
GFT-35 SPECIFICATIONS � � � � � � � � � � � � � � �6
GFT-35-CUS (BARREL) SPECS � � � � � � � � � � �7
CLEARANCES & VENTING � � � � � � � � � � � � � � �8
LOWER FLASHING INSTALL (BARREL) � � � � � �9
GAS SPECIFICATIONS� � � � � � � � � � � � � � � � �10
OPERATION � � � � � � � � � � � � � � � � � � � � � � � �11
LIMITED WARRANTY � � � � � � � � � � � � � � � � �14

Tandoor Installation
and Operation Manual
PG 3 OF 16
M0053.05 APRIL 2017
An ongoing program of product improvement may
require us to change specifications without notice.
WOOD STONE CORPORATION
1801 W. Bakerview Rd.
Bellingham, WA 98226 USA
TOLL FREE 800.988.8103
TEL [phone]
FAX [phone]
E-MAIL [e-mail]
woodstone-corp.com
TANDOOR
INSTALLATION AND OPERATION MANUAL FOR THE
WOOD STONE TANDOOR
GAS-FIRED TANDOOR OVEN
WS-GFT-31 (ROUND, SQUARE AND OCTAGONAL),
WS-GFT-35 (ROUND, SQUARE, OCTAGONAL)
AND WS-GFT-35-CUS (BARREL) MODELS
ADDITIONAL COPIES AVAILABLE UPON REQUEST
Square model (shown with
optional utensil rails, pan rail
w/ pans and shelf)
Round modelOctagonal model
Barrel model

Tandoor Installation
and Operation Manual
PG 4 OF 16
M0053.05 APRIL 2017
An ongoing program of product improvement may
require us to change specifications without notice.
WOOD STONE CORPORATION
1801 W. Bakerview Rd.
Bellingham, WA 98226 USA
TOLL FREE 800.988.8103
TEL [phone]
FAX [phone]
E-MAIL [e-mail]
woodstone-corp.com
CAUTIONS & WARNINGS
INSTALLATION AND OPERATING INSTRUCTIONS FOR THE WOOD STONE
GFT-31-(RND, SQR, OCT)-(NG, LP, HLP), GFT-35-(RND, SQR, OCT)-(NG, LP, HLP)
AND GFT-35-CUS-(NG, LP, HLP) TANDOOR OVENS
Wood Stone's Gas-Fired Tandoor ovens have been tested and approved by Intertek Testing Services,
and are ETL listed to ANSI Z83.11:2016 Ed. 4, CSA 1.8:2016 Ed. 4,
and to NSF/ANSI Standard 4.
WARNING: This product must be installed by a licensed plumber or gas fitter
when installed within the Commonwealth of Massachusetts.
DO NOT THROW THIS MANUAL AWAY
FOR YOUR SAFETY: Do not store or use gasoline or other flammable vapors or liquids in the vicinity of this or
any other appliance. Also, always keep the area under and around this appliance free and clear of any and all
combustible materials.
It is recommended that this oven be installed, maintained and
serviced by authorized professionals.
IMPORTANT: Consult your local gas supplier for a statement outlining a procedure to be followed in the event you smell
gas� Post the statement in a prominent location�
WARNING: Improper installation, adjustment, alteration, service or maintenance can result in property damage,
injury or death. Read the installation, operation and maintenance instructions thoroughly before installing or
servicing this equipment.
READ ALL INSTRUCTIONS BEFORE INSTALLING AND USING THIS APPLIANCE
Please read this entire manual before you install the oven. Failure to follow instructions may result in property
damage, bodily injury or even death. Contact your local building or fire officials about restrictions and installation
inspection in your area.
RETAIN THIS MANUAL FOR FUTURE REFERENCE
Additional copies of this manual at woodstone-corp�com�
For prompt responses to service/maintenance questions, call us at @ 1-800-988-8103�
ANSI Z83.11:2016 Ed.4
CSA 1.8:2016 Ed.4
ANSI/NSF STD 4

Tandoor Installation
and Operation Manual
PG 5 OF 16
M0053.05 APRIL 2017
An ongoing program of product improvement may
require us to change specifications without notice.
WOOD STONE CORPORATION
1801 W. Bakerview Rd.
Bellingham, WA 98226 USA
TOLL FREE 800.988.8103
TEL [phone]
FAX [phone]
E-MAIL [e-mail]
woodstone-corp.com
GFT-31 SPECIFICATIONS
REV:
LEGEND:
PART #:
WS-GFT-31-RND
31" Tandoor. All Shapes
General Arrangement
10/14/2013 bena
1
DWN BY:
SHEET:
Bellingham, WA 360/650-1111 www.woodstone-corp.com
DIMENSIONS ARE IN INCHES
TOLERANCES: LINEAR ±1/2 [±10mm], ANGULAR ±2°
UNLESS NOTED OTHERWISE
\\woodstone.net\dfs\CAD\0 Pn\WS Top Level\WS-GFT-31_General_Arrangement-1.dft
THE INFORMATION CONTAINED IN THIS DRAWING IS THE
SOLE PROPERTY OF WOOD STONE CORPORATION
ANY REPRODUCTION OR USE IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF WOOD STONE IS
PROHIBITED
AN ONGOING PROGRAM OF PRODUCT IMPROVEMENT
MAY REQUIRE US TO CHANGE SPECIFICATIONS
WITHOUT NOTICE.
DATE:
G
GAS INLET: 1/2" NPT
40,000 BTU, NG
40,000 BTU, LP
1 of 1
G
GG
30 3/4"
780mm
30 3/4"
780mm 30 3/4"
780mm
O
12"
300mm
Opening
O
12"
300mm
Opening
O
12"
300mm
Opening
12 3/4"
320mm
31"
790mm
37 3/4"
960mm
6 1/4"
160mm
21 1/2"
550mm
21"
530mm
Plan view (Round)
REV:
LEGEND:
PART #:
WS-GFT-31-RND
31" Tandoor. All Shapes
General Arrangement
10/14/2013 bena
1
DWN BY:
SHEET:
Bellingham, WA 360/650-1111 www.woodstone-corp.com
DIMENSIONS ARE IN INCHES
TOLERANCES: LINEAR ±1/2 [±10mm], ANGULAR ±2°
UNLESS NOTED OTHERWISE
\\woodstone.net\dfs\CAD\0 Pn\WS Top Level\WS-GFT-31_General_Arrangement-1.dft
THE INFORMATION CONTAINED IN THIS DRAWING IS THE
SOLE PROPERTY OF WOOD STONE CORPORATION
ANY REPRODUCTION OR USE IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF WOOD STONE IS
PROHIBITED
AN ONGOING PROGRAM OF PRODUCT IMPROVEMENT
MAY REQUIRE US TO CHANGE SPECIFICATIONS
WITHOUT NOTICE.
DATE:
G
GAS INLET: 1/2" NPT
40,000 BTU, NG
40,000 BTU, LP
1 of 1
GGG
30 3/4"
780mm 30 3/4"
780mm 30 3/4"
780mm
O
12"
300mm
Opening
O
12"
300mm
Opening
O
12"
300mm
Opening
12 3/4"
320mm
31"
790mm
37 3/4"
960mm
6 1/4"
160mm
21 1/2"
550mm
21"
530mm
Side view (Round)
REV:
LEGEND:
PART #:
WS-GFT-31-RND
31" Tandoor. All Shapes
General Arrangement
10/14/2013 bena
1
DWN BY:
SHEET:
Bellingham, WA 360/650-1111 www.woodstone-corp.com
DIMENSIONS ARE IN INCHES
TOLERANCES: LINEAR ±1/2 [±10mm], ANGULAR ±2°
UNLESS NOTED OTHERWISE
\\woodstone.net\dfs\CAD\0 Pn\WS Top Level\WS-GFT-31_General_Arrangement-1.dft
THE INFORMATION CONTAINED IN THIS DRAWING IS THE
SOLE PROPERTY OF WOOD STONE CORPORATION
ANY REPRODUCTION OR USE IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF WOOD STONE IS
PROHIBITED
AN ONGOING PROGRAM OF PRODUCT IMPROVEMENT
MAY REQUIRE US TO CHANGE SPECIFICATIONS
WITHOUT NOTICE.
DATE:
G
GAS INLET: 1/2" NPT
40,000 BTU, NG
40,000 BTU, LP
1 of 1
GGG
30 3/4"
780mm 30 3/4"
780mm 30 3/4"
780mm
O
12"
300mm
Opening
O
12"
300mm
Opening
O
12"
300mm
Opening
12 3/4"
320mm
31"
790mm
37 3/4"
960mm
6 1/4"
160mm
21 1/2"
550mm
21"
530mm
Front view (Round)
REV:
LEGEND:
PART #:
WS-GFT-31-RND
31" Tandoor. All Shapes
General Arrangement
10/14/2013 bena
1
DWN BY:
SHEET:
Bellingham, WA 360/650-1111 www.woodstone-corp.com
DIMENSIONS ARE IN INCHES
TOLERANCES: LINEAR ±1/2 [±10mm], ANGULAR ±2°
UNLESS NOTED OTHERWISE
\\woodstone.net\dfs\CAD\0 Pn\WS Top Level\WS-GFT-31_General_Arrangement-1.dft
THE INFORMATION CONTAINED IN THIS DRAWING IS THE
SOLE PROPERTY OF WOOD STONE CORPORATION
ANY REPRODUCTION OR USE IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF WOOD STONE IS
PROHIBITED
AN ONGOING PROGRAM OF PRODUCT IMPROVEMENT
MAY REQUIRE US TO CHANGE SPECIFICATIONS
WITHOUT NOTICE.
DATE:
G
GAS INLET: 1/2" NPT
40,000 BTU, NG
40,000 BTU, LP
1 of 1
G
G
G
30 3/4"
780mm
30 3/4"
780mm
30 3/4"
780mm
O
12"
300mm
Opening
O
12"
300mm
Opening
O
12"
300mm
Opening
12 3/4"
320mm
31"
790mm
37 3/4"
960mm
6 1/4"
160mm
21 1/2"
550mm
21"
530mm
Plan view (Square)
REV:
LEGEND:
PART #:
WS-GFT-31-RND
31" Tandoor. All Shapes
General Arrangement
10/14/2013 bena
1
DWN BY:
SHEET:
Bellingham, WA 360/650-1111 www.woodstone-corp.com
DIMENSIONS ARE IN INCHES
TOLERANCES: LINEAR ±1/2 [±10mm], ANGULAR ±2°
UNLESS NOTED OTHERWISE
\\woodstone.net\dfs\CAD\0 Pn\WS Top Level\WS-GFT-31_General_Arrangement-1.dft
THE INFORMATION CONTAINED IN THIS DRAWING IS THE
SOLE PROPERTY OF WOOD STONE CORPORATION
ANY REPRODUCTION OR USE IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF WOOD STONE IS
PROHIBITED
AN ONGOING PROGRAM OF PRODUCT IMPROVEMENT
MAY REQUIRE US TO CHANGE SPECIFICATIONS
WITHOUT NOTICE.
DATE:
G
GAS INLET: 1/2" NPT
40,000 BTU, NG
40,000 BTU, LP
1 of 1
GG
G
30 3/4"
780mm 30 3/4"
780mm
30 3/4"
780mm
O
12"
300mm
Opening
O
12"
300mm
Opening
O
12"
300mm
Opening
12 3/4"
320mm
31"
790mm
37 3/4"
960mm
6 1/4"
160mm
21 1/2"
550mm
21"
530mm
Plan view (Octagonal)
WS-GFT-31 (ROUND, OCTAGONAL AND SQUARE MODELS)
Note: Side and front
view dimensions are
the same for the Round,
Square and Octagonal
models�
UTILITY SPECIFICATIONS
Gas: 1/2-inch FNPT gas inlet
40,000 BTU/hr Natural Gas (NG) OR Propane (LP)
Gas type must be specified when ordering� Gas connection should
be made using an approved flexible connector and the unit must be
restrained in accordance with all relevant local and/or national codes�
Gas connection is made beneath unit at rear�
Venting
This appliance must be installed under a Type 1 exhaust hood, in
accordance with all relevant local and national codes, and in a manner
acceptable to the authority having jurisdiction� Please contact Wood
Stone for more detailed information�
Shipping weight:
750 lbs.
Air intake: Do not
facade or cover over

Tandoor Installation
and Operation Manual
PG 6 OF 16
M0053.05 APRIL 2017
An ongoing program of product improvement may
require us to change specifications without notice.
WOOD STONE CORPORATION
1801 W. Bakerview Rd.
Bellingham, WA 98226 USA
TOLL FREE 800.988.8103
TEL [phone]
FAX [phone]
E-MAIL [e-mail]
woodstone-corp.com
GFT-35 SPECIFICATIONS
REV:
LEGEND:
PART #:
WS-GFT-35-RND
35" Tandoor. All Shapes
General Arrangement
10/14/2013 bena
1
DWN BY:
SHEET:
Bellingham, WA 360/650-1111 www.woodstone-corp.com
DIMENSIONS ARE IN INCHES
TOLERANCES: LINEAR ±1/2 [±10mm], ANGULAR ±2°
UNLESS NOTED OTHERWISE
\\woodstone.net\dfs\CAD\0 Pn\WS Top Level\WS-GFT-35_General_Arrangement-1.dft
THE INFORMATION CONTAINED IN THIS DRAWING IS THE
SOLE PROPERTY OF WOOD STONE CORPORATION
ANY REPRODUCTION OR USE IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF WOOD STONE IS
PROHIBITED
AN ONGOING PROGRAM OF PRODUCT IMPROVEMENT
MAY REQUIRE US TO CHANGE SPECIFICATIONS
WITHOUT NOTICE.
DATE:
G
GAS INLET: 1/2" NPT
40,000 BTU, NG
40,000 BTU, LP
1 of 1
G
G
34 3/4"
880mm
O
13"
330mm
Opening
O
13"
330mm
Opening
40 3/4"
1040mm
34 3/4"
880mm
G
O
13"
330mm
Opening
34 3/4"
880mm
14 1/4"
360mm
33 3/4"
860mm
6 1/4"
160mm
24 1/2"
620mm
24 3/4"
630mm
Plan view (Round)
REV:
LEGEND:
PART #:
WS-GFT-35-RND
35" Tandoor. All Shapes
General Arrangement
10/14/2013 bena
1
DWN BY:
SHEET:
Bellingham, WA 360/650-1111 www.woodstone-corp.com
DIMENSIONS ARE IN INCHES
TOLERANCES: LINEAR ±1/2 [±10mm], ANGULAR ±2°
UNLESS NOTED OTHERWISE
\\woodstone.net\dfs\CAD\0 Pn\WS Top Level\WS-GFT-35_General_Arrangement-1.dft
THE INFORMATION CONTAINED IN THIS DRAWING IS THE
SOLE PROPERTY OF WOOD STONE CORPORATION
ANY REPRODUCTION OR USE IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF WOOD STONE IS
PROHIBITED
AN ONGOING PROGRAM OF PRODUCT IMPROVEMENT
MAY REQUIRE US TO CHANGE SPECIFICATIONS
WITHOUT NOTICE.
DATE:
G
GAS INLET: 1/2" NPT
40,000 BTU, NG
40,000 BTU, LP
1 of 1
G G
34 3/4"
880mm
O
13"
330mm
Opening
O
13"
330mm
Opening
40 3/4"
1040mm
34 3/4"
880mm
G
O
13"
330mm
Opening
34 3/4"
880mm
14 1/4"
360mm
33 3/4"
860mm
6 1/4"
160mm
24 1/2"
620mm
24 3/4"
630mm
Side view (Round)
REV:
LEGEND:
PART #:
WS-GFT-35-RND
35" Tandoor. All Shapes
General Arrangement
10/14/2013 bena
1
DWN BY:
SHEET:
Bellingham, WA 360/650-1111 www.woodstone-corp.com
DIMENSIONS ARE IN INCHES
TOLERANCES: LINEAR ±1/2 [±10mm], ANGULAR ±2°
UNLESS NOTED OTHERWISE
\\woodstone.net\dfs\CAD\0 Pn\WS Top Level\WS-GFT-35_General_Arrangement-1.dft
THE INFORMATION CONTAINED IN THIS DRAWING IS THE
SOLE PROPERTY OF WOOD STONE CORPORATION
ANY REPRODUCTION OR USE IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF WOOD STONE IS
PROHIBITED
AN ONGOING PROGRAM OF PRODUCT IMPROVEMENT
MAY REQUIRE US TO CHANGE SPECIFICATIONS
WITHOUT NOTICE.
DATE:
G
GAS INLET: 1/2" NPT
40,000 BTU, NG
40,000 BTU, LP
1 of 1
G G
34 3/4"
880mm
O
13"
330mm
Opening
O
13"
330mm
Opening
40 3/4"
1040mm
34 3/4"
880mm
G
O
13"
330mm
Opening
34 3/4"
880mm
14 1/4"
360mm
33 3/4"
860mm
6 1/4"
160mm
24 1/2"
620mm
24 3/4"
630mm
Front view (Round)
REV:
LEGEND:
PART #:
WS-GFT-35-RND
35" Tandoor. All Shapes
General Arrangement
10/14/2013 bena
1
DWN BY:
SHEET:
Bellingham, WA 360/650-1111 www.woodstone-corp.com
DIMENSIONS ARE IN INCHES
TOLERANCES: LINEAR ±1/2 [±10mm], ANGULAR ±2°
UNLESS NOTED OTHERWISE
\\woodstone.net\dfs\CAD\0 Pn\WS Top Level\WS-GFT-35_General_Arrangement-1.dft
THE INFORMATION CONTAINED IN THIS DRAWING IS THE
SOLE PROPERTY OF WOOD STONE CORPORATION
ANY REPRODUCTION OR USE IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF WOOD STONE IS
PROHIBITED
AN ONGOING PROGRAM OF PRODUCT IMPROVEMENT
MAY REQUIRE US TO CHANGE SPECIFICATIONS
WITHOUT NOTICE.
DATE:
G
GAS INLET: 1/2" NPT
40,000 BTU, NG
40,000 BTU, LP
1 of 1
G G
34 3/4"
880mm
O
13"
330mm
Opening
O
13"
330mm
Opening
40 3/4"
1040mm
34 3/4"
880mm
G
O
13"
330mm
Opening
34 3/4"
880mm
14 1/4"
360mm
33 3/4"
860mm
6 1/4"
160mm
24 1/2"
620mm
24 3/4"
630mm
Plan view (Square)
REV:
LEGEND:
PART #:
WS-GFT-35-RND
35" Tandoor. All Shapes
General Arrangement
10/14/2013 bena
1
DWN BY:
SHEET:
Bellingham, WA 360/650-1111 www.woodstone-corp.com
DIMENSIONS ARE IN INCHES
TOLERANCES: LINEAR ±1/2 [±10mm], ANGULAR ±2°
UNLESS NOTED OTHERWISE
\\woodstone.net\dfs\CAD\0 Pn\WS Top Level\WS-GFT-35_General_Arrangement-1.dft
THE INFORMATION CONTAINED IN THIS DRAWING IS THE
SOLE PROPERTY OF WOOD STONE CORPORATION
ANY REPRODUCTION OR USE IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF WOOD STONE IS
PROHIBITED
AN ONGOING PROGRAM OF PRODUCT IMPROVEMENT
MAY REQUIRE US TO CHANGE SPECIFICATIONS
WITHOUT NOTICE.
DATE:
G
GAS INLET: 1/2" NPT
40,000 BTU, NG
40,000 BTU, LP
1 of 1
G
G
34 3/4"
880mm
O
13"
330mm
Opening
O
13"
330mm
Opening
40 3/4"
1040mm
34 3/4"
880mm
G
O
13"
330mm
Opening
34 3/4"
880mm
14 1/4"
360mm
33 3/4"
860mm
6 1/4"
160mm
24 1/2"
620mm
24 3/4"
630mm
Plan view (Octagonal)
WS-GFT-35 (ROUND, OCTAGONAL AND SQUARE MODELS)
Note: Side and front
view dimensions are
the same for the Round,
Square and Octagonal
models�
UTILITY SPECIFICATIONS
Gas: 1/2-inch FNPT gas inlet
40,000 BTU/hr Natural Gas (NG) OR Propane (LP)
Gas type must be specified when ordering� Gas connection should
be made using an approved flexible connector and the unit must be
restrained in accordance with all relevant local and/or national codes�
Gas connection is made beneath unit at rear�
Venting
This appliance must be installed under a Listed Type 1 exhaust hood, in
accordance with all relevant local and national codes, and in a manner
acceptable to the authority having jurisdiction� Please contact Wood
Stone for more detailed information�
Shipping weight:
950 lbs.
Air intake: Do not
facade or cover over

Tandoor Installation
and Operation Manual
PG 7 OF 16
M0053.05 APRIL 2017
An ongoing program of product improvement may
require us to change specifications without notice.
WOOD STONE CORPORATION
1801 W. Bakerview Rd.
Bellingham, WA 98226 USA
TOLL FREE 800.988.8103
TEL [phone]
FAX [phone]
E-MAIL [e-mail]
woodstone-corp.com
GFT-35-CUS (BARREL) SPECS
WS-GFT-35-CUS (BARREL MODEL)
Plan view
Side view
REV:
LEGEND:
PART #:
001-5031-BRL-3521
3521 - Barrel Tandoor
General Arrangement
12/21/2016 lucasm 3
DWN BY:
SHEET:
Bellingham, WA 360/650-1111 www.woodstone-corp.com
DIMENSIONS ARE IN INCHES
TOLERANCES: LINEAR ±1/2 [±10mm], ANGULAR ±2°
UNLESS NOTED OTHERWISE
\\woodstone\dfs\CAD\0 Pn\WS Top Level\WS-GFT-Gas_Fired_Tandoor\WS-GFT-35-BRL_General_Arrangement-3.dft
THE INFORMATION CONTAINED IN THIS DRAWING IS THE
SOLE PROPERTY OF WOOD STONE CORPORATION
ANY REPRODUCTION OR USE IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF WOOD STONE IS
PROHIBITED
AN ONGOING PROGRAM OF PRODUCT IMPROVEMENT
MAY REQUIRE US TO CHANGE SPECIFICATIONS
WITHOUT NOTICE.
DATE:
G
120VAC, 2A
GAS INLET: 1/2" NPT
40,000 BTU, NG
40,000 BTU, LP
1 of 1
G
G
16 1/4"
410mm 36 1/4"
920mm
2"
50mm
14 3/4"
370mm
21"
530mm
O12"
300mm
Opening
35"
890mm
36 1/4"35 1/4"-920mm900mm-
Height Adjustable
7"
180mm
21 1/2"
550mm
3"
80mm
O30 3/4"
780mm
Granite
Front view
REV:
LEGEND:
PART #:
001-5031-BRL-3521
3521 - Barrel Tandoor
General Arrangement
12/21/2016 lucasm 3
DWN BY:
SHEET:
Bellingham, WA 360/650-1111 www.woodstone-corp.com
DIMENSIONS ARE IN INCHES
TOLERANCES: LINEAR ±1/2 [±10mm], ANGULAR ±2°
UNLESS NOTED OTHERWISE
\\woodstone\dfs\CAD\0 Pn\WS Top Level\WS-GFT-Gas_Fired_Tandoor\WS-GFT-35-BRL_General_Arrangement-3.dft
THE INFORMATION CONTAINED IN THIS DRAWING IS THE
SOLE PROPERTY OF WOOD STONE CORPORATION
ANY REPRODUCTION OR USE IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF WOOD STONE IS
PROHIBITED
AN ONGOING PROGRAM OF PRODUCT IMPROVEMENT
MAY REQUIRE US TO CHANGE SPECIFICATIONS
WITHOUT NOTICE.
DATE:
G
120VAC, 2A
GAS INLET: 1/2" NPT
40,000 BTU, NG
40,000 BTU, LP
1 of 1
G
G
16 1/4"
410mm
36 1/4"
920mm
2"
50mm
14 3/4"
370mm
21"
530mm
O12"
300mm
Opening
35"
890mm
36 1/4"35 1/4"-920mm900mm-
Height Adjustable
7"
180mm
21 1/2"
550mm
3"
80mm
O30 3/4"
780mm
Granite
REV:
LEGEND:
PART #:
001-5031-BRL-3521
3521 - Barrel Tandoor
General Arrangement
12/21/2016 lucasm 3
DWN BY:
SHEET:
Bellingham, WA 360/650-1111 www.woodstone-corp.com
DIMENSIONS ARE IN INCHES
TOLERANCES: LINEAR ±1/2 [±10mm], ANGULAR ±2°
UNLESS NOTED OTHERWISE
\\woodstone\dfs\CAD\0 Pn\WS Top Level\WS-GFT-Gas_Fired_Tandoor\WS-GFT-35-BRL_General_Arrangement-3.dft
THE INFORMATION CONTAINED IN THIS DRAWING IS THE
SOLE PROPERTY OF WOOD STONE CORPORATION
ANY REPRODUCTION OR USE IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF WOOD STONE IS
PROHIBITED
AN ONGOING PROGRAM OF PRODUCT IMPROVEMENT
MAY REQUIRE US TO CHANGE SPECIFICATIONS
WITHOUT NOTICE.
DATE:
G
120VAC, 2A
GAS INLET: 1/2" NPT
40,000 BTU, NG
40,000 BTU, LP
1 of 1
G
G
16 1/4"
410mm
36 1/4"
920mm
2"
50mm
14 3/4"
370mm
21"
530mm
O12"
300mm
Opening
35"
890mm
36 1/4"35 1/4"-920mm900mm-
Height Adjustable
7"
180mm
21 1/2"
550mm
3"
80mm
O30 3/4"
780mm
Granite
UTILITY SPECIFICATIONS
Gas
1/2-inch FNPT gas inlet
40,000 BTU/hr Natural Gas (NG) OR Propane (LP)
Gas type must be specified when ordering� Gas connection should
be made using an approved flexible connector and the unit must be
restrained in accordance with all relevant local and/or national codes�
Gas connection is made beneath the unit at the rear�
Venting
This appliance must be installed under a Listed Type
1 exhaust hood, in accordance with all relevant local
and national codes, and in a manner acceptable
to the authority having jurisdiction� Please contact
Wood Stone for more detailed information�
Shipping weight:
750 lbs.
Air intake: Do not
facade or cover over

Tandoor Installation
and Operation Manual
PG 8 OF 16
M0053.05 APRIL 2017
An ongoing program of product improvement may
require us to change specifications without notice.
WOOD STONE CORPORATION
1801 W. Bakerview Rd.
Bellingham, WA 98226 USA
TOLL FREE 800.988.8103
TEL [phone]
FAX [phone]
E-MAIL [e-mail]
woodstone-corp.com
CLEARANCES & VENTING
Combustible construction overhanging
the appliance should be protected in a
manner acceptable to the authority having
jurisdiction.
Install on a noncombustible floor, or one protected
in a manner acceptable to the authority having
jurisdiction, extending 36 inches in all directions.
1-inch side clearance
to combustible
construction
INSTALLATION CLEARANCES
The Wood Stone gas-fired Tandoor must be installed with at least
1-inch side clearance to combustible construction� Install the unit
on a non-combustible floor, or one provided with a non-combustible
covering that extends at least 36-inches in all directions� Any
combustible construction above (overhanging) the appliance should be
protected in a manner acceptable to the authority having jurisdiction�
ENCLOSURES
If the appliance is enclosed, provisions should be made so that it can
easily be removed from the enclosure�
VENTING
The Wood Stone gas-fired Tandoor must be installed under an appropriate NFPA 96 approved Type 1 exhaust hood� Refer to
local and/or national codes for hood specification requirements� The hood must be designed for the removal of the combustion
products of gas, as well as the cooking vapors related to the intended use of the oven�
Some jurisdictions may require that the Tandoor be interlocked to the hood ventilation system to prevent operation of the
appliance when the ventilation system is not turned on� If an interlock is required, use an approved gas solenoid (supplied and
installed by others), wired so that the gas supply to the appliance is turned off whenever the ventilation system is turned off�
!WARNING: Do not pack required air space (clearance) with insulation or other materials. When
non-combustible building materials contact the body of the oven, the clearances to combustibles
are transferred to those non-combustibles.
Shaded area must be left unobstructed for critical
combustion air and easily accessible for removal
of the drip/debris pan and operation of the pilot
safety valve. If this area must be covered, the
cover should be easily removable and heavily
perforated.

PG 9 OF 16
M0053.05 APRIL 2017
Tandoor Installation
and Operation Manual
LOWER FLASHING INSTALL (BARREL)
DO NOT LOWER STRIP FLASHING UNTIL TANDOOR IS LOCATED IN ITS FINAL INSTALLED POSITION
Leveling the Tandoor
Position Tandoor in its final installed position�
With the Flashing still in the UP position, level
the Tandoor using the four adjustable feet�
Plumbing the Tandoor
If the gas connection is made below the
Tandoor, plumb before lowering the flange�
If the gas connection is not from below the
Tandoor, it will be necessary to notch the flashing�
This should be done after the flashing
is lowered�
Lowering the Flashing
The unit ships with the Strip Flashing secured into
its “UP” position with a screw at each leg�
Screw holding up
flashing
Remove the screw from all 4 legs and lower the
flashing evenly around the Tandoor, flat to the floor�
Center punch and pre-drill each Leg using the
existing hole in the flashing as a guide�
Secure the flashing at each leg using the screw
previously removed�
Remove the protective black Edge Cover�
Center punch and
pre-drill using the
existing hole as a guide,
then fasten with screw
Protective black Edge Cover
• • ••
Ü
• • ••
Ü
• • ••
Ü

Tandoor Installation
and Operation Manual
PG 10 OF 16
M0053.05 APRIL 2017
An ongoing program of product improvement may
require us to change specifications without notice.
WOOD STONE CORPORATION
1801 W. Bakerview Rd.
Bellingham, WA 98226 USA
TOLL FREE 800.988.8103
TEL [phone]
FAX [phone]
E-MAIL [e-mail]
woodstone-corp.com
GAS SPECIFICATIONS
GAS CONNECTION
The gas connection is made at the lower rear of the appliance. See next page for details.
This appliance (except the barrel model) is equipped with casters; it must be installed using the casters supplied with
a connector complying with ANSI Z21.69 or CAN/CGA 1-6.9 and a quick disconnect device complying with ANSI Z21.41
or CAN 1-6.9. It must also be installed with restraining means to guard against transmission of strain to the connector.
IMPORTANT: The gas supply to this appliance should be equipped with an individual appliance shutoff valve that
is capable of completely isolating the appliance from the main gas supply. This valve should be installed in such a
manner as to be readily accessible to the operator of the appliance.
The Wood Stone gas-fired Tandoor is equipped with a 1/2-inch FNPT connection, located on the underside of the rear of the
unit� Anchor points for the restraining means are provided on the underside of the Tandoor; these are holes punched in the rear
portion of the drip/debris pan rails�
GAS RATINGS
Natural Gas
GFT-31, GFT-35, GFT-35-CUS models
40,000 BTU/hr supply
4�0" W�C� manifold pressure
Propane
GFT-31, GFT-35, GFT-35-CUS models
40,000 BTU/hr supply
10�0" W�C� manifold pressure
THIS APPLIANCE IS NOT FOR USE WITH SOLID FUEL
GAS CODE LIMITATIONS
The installation of this appliance must conform with local codes, or in the absence of local codes, with the National Fuel Gas
Code, ANSI Z223�1, or The Natural Gas Installation Code CAN/CGA-B149�1 as applicable�
The appliance and its individual shutoff valve (supplied by others) must be disconnected from the gas supply piping system
during any pressure testing of that system at test pressures in excess of 1/2 psi (3�45 kPa)�
The appliance must be isolated from the gas supply piping system by closing its individual manual shutoff valve (supplied by
others) during any pressure testing of the gas supply piping system at test pressure, equal to or less than 1/2 psi (3�45 kPa)�