Wood Stone WS-FD-9660-L-IR-CL User manual

Toll Free 800.988.8103
Tel [phone]
Fax [phone]
www.woodstone-corp.com
WOOD STONE CORPORATION
1801 W. Bakerview Rd.
Bellingham, WA 98226 USA
COAL-FIRED OVEN
Stone Hearth Speciality Oven
Gas/Coal Combination Models
FIRE DECK 9660 WS-FD-9660-CL
FIRE DECK 11260 WS-FD-11260-CL
DOC NO M0044.03 REVISED November 2015
Installation and
Operation Manual

2
9660 & 11260 Fire Deck Coal-Fired Oven
Installation and Operation Manual
TABLE OF CONTENTS
An ongoing program of product improvement may require us to change
specifications without notice. FD-9660-CL, FD-11260-CL,
Revised November 2015. Doc no: M0044.03
[email protected] or visit woodstone-corp.com
Wood Stone Corporation
1801 W. Bakerview Rd.
Bellingham, WA 98226 USA
Toll Free 800.988.8103
Tel [phone]
Fax [phone]
TABLE OF CONTENTS
COAL-FIRED OVENS� � � � � � � � � � � � � � � � � � � � � � � � 3
CAUTIONS AND WARNINGS � � � � � � � � � � � � � � � � � � 4
UNLOADING AND MOVING � � � � � � � � � � � � � � � � � � � 6
INSTALLATION CASTERS � � � � � � � � � � � � � � � � � � � � 7
9660-CL SPECIFICATIONS � � � � � � � � � � � � � � � � � � � 8
11260-CL SPECIFICATIONS � � � � � � � � � � � � � � � � � � 9
PLACING AND INSTALLATION � � � � � � � � � � � � � � � � 10
INSTALLATION CLEARANCES � � � � � � � � � � � � � � � � 11
GAS SPECIFICATIONS� � � � � � � � � � � � � � � � � � � � � � 13
VENTING � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 14
WOOD STONE HOODS � � � � � � � � � � � � � � � � � � � � � 16
CONTROLLER � � � � � � � � � � � � � � � � � � � � � � � � � � � 18
INITIAL START-UP � � � � � � � � � � � � � � � � � � � � � � � � 20
DAILY OVEN OPERATION� � � � � � � � � � � � � � � � � � � � 21
USE OF COAL OVERVIEW � � � � � � � � � � � � � � � � � � � 22
DAILY MAINTENANCE� � � � � � � � � � � � � � � � � � � � � � 27
PERIODIC THERMAL CLEANING � � � � � � � � � � � � � � 28
TROUBLESHOOTING GUIDE � � � � � � � � � � � � � � � � � 29
ELECTRICAL DIAGRAMS� � � � � � � � � � � � � � � � � � � � 30
INTERLOCK DIAGRAM � � � � � � � � � � � � � � � � � � � � � 33
LIMITED WARRANTY � � � � � � � � � � � � � � � � � � � � � � 34

3
9660 & 11260 Fire Deck Coal-Fired Oven
Installation and Operation Manual
COAL-FIRED OVENS
INSTALLATION AND OPERATION MANUAL FOR THE
WOOD STONE FIRE DECK COAL-FIRED OVEN
STONE HEARTH COOKING EQUIPMENT
FIRE DECK COAL-FIRED OVEN
WS-FD-9660-(L,R)-IR-CL AND WS-FD-11260-(L,R)-IR-CL
ADDITIONAL MANUAL COPIES AVAILABLE UPON REQUEST
Shown: WS-FD-9660-RFG-L-IR-CL
An ongoing program of product improvement may require us to change
specifications without notice. FD-9660-CL, FD-11260-CL,
Revised November 2015. Doc no: M0044.03
[email protected] or visit woodstone-corp.com
Wood Stone Corporation
1801 W. Bakerview Rd.
Bellingham, WA 98226 USA
Toll Free 800.988.8103
Tel [phone]
Fax [phone]

RETAIN THIS MANUAL FOR FUTURE REFERENCE
Additional copies of this manual at woodstone-corp�com�
For prompt responses to service/maintenance questions, call us at @ 1-800-988-8103�
4
9660 & 11260 Fire Deck Coal-Fired Oven
Installation and Operation Manual
CAUTIONS AND WARNINGS
An ongoing program of product improvement may require us to change
specifications without notice. FD-9660-CL, FD-11260-CL,
Revised November 2015. Doc no: M0044.03
[email protected] or visit woodstone-corp.com
Wood Stone Corporation
1801 W. Bakerview Rd.
Bellingham, WA 98226 USA
Toll Free 800.988.8103
Tel [phone]
Fax [phone]
INSTALLATION AND OPERATION MANUAL FOR THE
WOOD STONE FIRE DECK OVEN
STONE HEARTH COOKING EQUIPMENT
WS-FD-9660-CL AND WS-FD-11260-CL MODELS EQUIPPED FOR COAL BURNING
ADDITIONAL COPIES AVAILABLE UPON REQUEST
READ ALL INSTRUCTIONS BEFORE INSTALLING AND USING THIS APPLIANCE
Please read this entire manual before you install the oven. Failure to follow instructions may result in
property damage, bodily injury or even death. Contact your local building or fire officials about restrictions
and installation inspection in your area.
WARNING: Improper installation, adjustment, alteration, service or maintenance can result in property
damage, injury or death. Read the installation, operation and maintenance instructions thoroughly before
installing or servicing this equipment.
IF THIS OVEN IS NOT PROPERLY INSTALLED A FIRE MAY RESULT. TO REDUCE THE RISK OF FIRE, FOLLOW
THESE INSTALLATION INSTRUCTIONS. A MAJOR CAUSE OF OVEN RELATED FIRES IS FAILURE TO MAINTAIN
REQUIRED CLEARANCES (AIR SPACES) TO COMBUSTIBLE MATERIALS. IT IS OF THE UTMOST IMPORTANCE
THAT THIS OVEN BE INSTALLED ONLY IN ACCORDANCE WITH THESE INSTRUCTIONS.
COAL FUEL - TO ENSURE CLEANEST EMISSIONS POSSIBLE, USE ONLY ANTHRACITE COAL. MANY VARIETIES
OF COAL CONTAIN CHEMICAL IMPURITIES THAT CAN DAMAGE THE OVEN CERAMIC. USING ANTHRACITE
COAL MINIMIZES THE CHANCE OF CHEMICAL DAMAGE TO THE OVEN CERAMIC. USE OF ANY COAL OTHER
THAN ANTHRACITE COAL WILL VOID THE WARRANTY ON THE OVEN CERAMIC AND MAY LEAD TO INCREASED
PARTICULATE AND OTHER EMISSIONS FROM THE OVEN WHEN COAL IS USED.

5
9660 & 11260 Fire Deck Coal-Fired Oven
Installation and Operation Manual
CAUTIONS AND WARNINGS
An ongoing program of product improvement may require us to change
specifications without notice. FD-9660-CL, FD-11260-CL,
Revised November 2015. Doc no: M0044.03
[email protected] or visit woodstone-corp.com
Wood Stone Corporation
1801 W. Bakerview Rd.
Bellingham, WA 98226 USA
Toll Free 800.988.8103
Tel [phone]
Fax [phone]
Wood Stone¹s Fire Deck Coal-Fired Ovens have been tested and approved by Intertek Testing
Services and ETL Listed to ANSI Z83.11b-2009, CSA 1.8b-2009, UL 737, ULC -S627-00,
UL Subject 2162, and to ANSI/NSF Standard 4.
SAVE THE INSTRUCTIONS
ANSI Z83.11b-2009
CSA 1.8b-2009
ANSI/NSF STD 4
FOR YOUR SAFETY: Do not store or use gasoline or other flammable vapors or liquids in the vicinity of this
or any other appliance. Also, always keep the area under and around this appliance free and clear of any
and all combustible materials.
It is recommended that this oven be installed, maintained and
serviced by authorized professionals.
WARNING: This product must be installed by a licensed plumber or gas fitter when installed within the
Commonwealth of Massachusetts.
FOR YOUR SAFETY: Consult your local gas supplier for a statement outlining a procedure to be followed
in the event you smell gas. Post the statement in a prominent location.
CAUTION: DISCONNECT POWER TO THE OVEN BEFORE SERVICING OR CLEANING.
CAUTION: Never use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter fluid or similar liquids
to start or freshen up a fire in this oven. Keep all such liquids well away from this oven when in use.
WARNING: In the event of a power failure, no attempt should be made to operate this appliance.

6
9660 & 11260 Fire Deck Coal-Fired Oven
Installation and Operation Manual
UNLOADING AND MOVING
An ongoing program of product improvement may require us to change
specifications without notice. FD-9660-CL, FD-11260-CL,
Revised November 2015. Doc no: M0044.03
[email protected] or visit woodstone-corp.com
Wood Stone Corporation
1801 W. Bakerview Rd.
Bellingham, WA 98226 USA
Toll Free 800.988.8103
Tel [phone]
Fax [phone]
USE A FORKLIFT RATED FOR AT
LEAST 10,000 LBS.
FORKS MUST BE AT LEAST 6'
IN LENGTH
10,000 LBS. FORKLIFT REQUIRED FOR LIFTING THE OVEN
The Fire Deck 9660 weighs approximately 6,000 lbs� and the Fire Deck 11260 weighs approximately 6,800 lbs� Use a forklift rated
to lift 10,000 lbs� Fork length must be at least 6 feet long (if not, fork extensions must be used)�When using a forklift, always use the
forklift pockets; lifting the oven any other way will result in damage� The fork pockets accommodate fork up to 9 inches wide� There
are fork pockets at the front and sides of the oven� The oven may also be rolled across a flat surface using the optional removable
casters� Please see the instructions on the following page for installing and removing the optional casters�
DELIVERY NOTE: The customer will receive an Oven Shipping Notification when the oven leaves the Wood Stone factory� This
will include a PRO# and a trucking company contact number� Wood Stone recommends that you confirm the delivery date/
time with the trucking company before committing to heavy equipment and/or labor� Our goal is a smooth and safe delivery�
DO NOT DROP THIS OVEN ABRUPTLY. ALWAYS USE A FORKLIFT OR CRANE TO LIFT THE OVEN.
DO NOT ATTEMPT TO USE A LEVER OF ANY TYPE TO RAISE THIS OVEN.
DO NOT TURN THE OVEN ON ITS SIDE!
Moving a Wood Stone oven can present
interesting challenges to even the most
experienced riggers� Make sure to secure
the proper equipment and make safety
your first priority� Please don’t hesitate to
call the factory for technical support�
IF YOU ARE GOING TO USE A
CRANE TO UNLOAD THE OVEN,
SPECIFY A FLATBED TRUCK
DELIVERY!
Use the pick-eyes provided on the
sides of the oven to lift the oven with
a crane. The spreader bar should
be of a sufficient length to keep the
sling from contacting the oven.
Moving a Wood Stone Fire Deck 9660 or Fire Deck 11260 oven can present challenges to even the most experienced riggers� Make
sure to secure the proper equipment and make safety your first priority� Please don’t hesitate to call the factory for technical support
at 1�800�988�8103�

7
9660 & 11260 Fire Deck Coal-Fired Oven
Installation and Operation Manual
INSTALLATION CASTERS
An ongoing program of product improvement may require us to change
specifications without notice. FD-9660-CL, FD-11260-CL,
Revised November 2015. Doc no: M0044.03
[email protected] or visit woodstone-corp.com
Wood Stone Corporation
1801 W. Bakerview Rd.
Bellingham, WA 98226 USA
Toll Free 800.988.8103
Tel [phone]
Fax [phone]
INSTRUCTIONS FOR INSTALLING AND REMOVING OPTIONAL INSTALLATION CASTERS
1. Use a forklift to raise the oven�
Once the casters are installed, lower the oven� It may then be rolled over a FLAT surface to its final destination�
3. Once in place, use two jacks to lift the left side
of the oven� Place one jack under each caster
assembly on the left side of the oven� Raise the
oven just high enough so the wheels clear the
floor� Unbolt each caster and remove it�
4. Lower the oven back to the ground� Remove the
self-tapping screw and slide the rest of the caster
assembly out of the fork pocket� Repeat steps 3
and 4for the right side of the oven�
Caster bolts
2. Insert a caster assembly into each of the side
fork pockets and secure it to the oven with a
self-tapping screw and washer� Install the screw
through the mounting tab�
DANGER: The Fire Deck 9660 weighs 6,000 lbs. and the Fire Deck 11260 weighs 6,800 lbs. Do not attempt to move the
oven over any type of grade or sloped surface. Failure to follow these instructions may result in severe injury or death.
BE SAFE. If you have any questions call Wood Stone at 800.988.8103.
NOTE: The casters will add 3" to the total height of the oven, for a total of 82-1/2".

8
9660 & 11260 Fire Deck Coal-Fired Oven
Installation and Operation Manual
Side view
Plan view
Front view
9660-CL SPECIFICATIONS
UTILITY SPECIFICATIONS
Gas: 1" FNPT gas inlet
225,000 BTU/hr Natural Gas (NG)
OR
225,000 BTU/hr Propane (LP)
Venting
This oven may be vented with a Listed Type 1 exhaust hood OR directly connected at the
12-inch O�D� oven flue collar to a power-ventilated, grease-rated chimney OR an exhaust
hood constructed in accordance with NFPA 96 and all relevant local and national codes�
The oven must be vented in accordance with all relevant local and national codes, and in
a manner acceptable to the authority having jurisdiction�
IMPORTANT: This model must be vented as a solid fuel appliance�
Electrical
120 VAC, 4 A, 50/60 Hz
Utility connections made on
left side of oven as shown�
Unit weight:
5,700 lbs
Shipping weight:
6,000 lbs.
Model shown: WS-FD-9660-RFG-L-CL
An ongoing program of product improvement may require us to change
specifications without notice. FD-9660-CL, FD-11260-CL,
Revised November 2015. Doc no: M0044.03
[email protected] or visit woodstone-corp.com
Wood Stone Corporation
1801 W. Bakerview Rd.
Bellingham, WA 98226 USA
Toll Free 800.988.8103
Tel [phone]
Fax [phone]
REV:
LEGEND:
PART #:
001-509660-CL
9660 Oven - Coal Right
General Arrangement
9/18/2013 bena
1
DWN BY:
SHEET:
Bellingham, WA 360/650-1111 www.woodstone-corp.com
DIMENSIONS ARE IN INCHES
TOLERANCES: LINEAR ±1/2 [±10mm], ANGULAR ±2°
UNLESS NOTED OTHERWISE
\\woodstone.net\dfs\CAD\0 Pn\WS Top Level\FD-9660-CL_General_Arrangement-1.dft
THE INFORMATION CONTAINED IN THIS DRAWING IS THE
SOLE PROPERTY OF WOOD STONE CORPORATION
ANY REPRODUCTION OR USE IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF WOOD STONE IS
PROHIBITED
AN ONGOING PROGRAM OF PRODUCT IMPROVEMENT
MAY REQUIRE US TO CHANGE SPECIFICATIONS
WITHOUT NOTICE.
DATE:
G
120VAC, 4A
GAS INLET: 1" NPT
225,000 BTU, NG
225,000 BTU, LP
1 of 1
G
G
57 3/4"
1470mm
53 3/4"
1370mm
10"
250mm
12"
300mm OD
95 3/4"
2430mm
48 1/4"
1230mm
37 1/2"
950mm
14"
360mm
9 3/4"
250mm
10 1/4"
260mm
33 3/4"
860mm
24 3/4"
630mm
25 1/2"
650mm
77 3/4"
1970mm
2"
50mm
57 1/2"
1460mm
10"
250mm
AIR INTAKE
6"
150mm
29 3/4"
760mm
33 3/4"
860mm
67 1/4"
1710mm
7 1/2"
190mm
7 1/4"
180mm
19"
480mm
13 1/2"
340mm
1"
30mm
1 1/2"
40mm
REV:
LEGEND:
PART #:
001-509660-CL
9660 Oven - Coal Right
General Arrangement
9/18/2013 bena
1
DWN BY:
SHEET:
Bellingham, WA 360/650-1111 www.woodstone-corp.com
DIMENSIONS ARE IN INCHES
TOLERANCES: LINEAR ±1/2 [±10mm], ANGULAR ±2°
UNLESS NOTED OTHERWISE
\\woodstone.net\dfs\CAD\0 Pn\WS Top Level\FD-9660-CL_General_Arrangement-1.dft
THE INFORMATION CONTAINED IN THIS DRAWING IS THE
SOLE PROPERTY OF WOOD STONE CORPORATION
ANY REPRODUCTION OR USE IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF WOOD STONE IS
PROHIBITED
AN ONGOING PROGRAM OF PRODUCT IMPROVEMENT
MAY REQUIRE US TO CHANGE SPECIFICATIONS
WITHOUT NOTICE.
DATE:
G
120VAC, 4A
GAS INLET: 1" NPT
225,000 BTU, NG
225,000 BTU, LP
1 of 1
G
G
57 3/4"
1470mm
53 3/4"
1370mm
10"
250mm
12"
300mm OD
95 3/4"
2430mm
48 1/4"
1230mm
37 1/2"
950mm
14"
360mm
9 3/4"
250mm
10 1/4"
260mm
33 3/4"
860mm
24 3/4"
630mm
25 1/2"
650mm
77 3/4"
1970mm
2"
50mm
57 1/2"
1460mm
10"
250mm
AIR INTAKE
6"
150mm
29 3/4"
760mm
33 3/4"
860mm
67 1/4"
1710mm
7 1/2"
190mm
7 1/4"
180mm
19"
480mm
13 1/2"
340mm
1"
30mm
1 1/2"
40mm
REV:
LEGEND:
PART #:
001-509660-CL
9660 Oven - Coal Right
General Arrangement
9/18/2013 bena
1
DWN BY:
SHEET:
Bellingham, WA 360/650-1111 www.woodstone-corp.com
DIMENSIONS ARE IN INCHES
TOLERANCES: LINEAR ±1/2 [±10mm], ANGULAR ±2°
UNLESS NOTED OTHERWISE
\\woodstone.net\dfs\CAD\0 Pn\WS Top Level\FD-9660-CL_General_Arrangement-1.dft
THE INFORMATION CONTAINED IN THIS DRAWING IS THE
SOLE PROPERTY OF WOOD STONE CORPORATION
ANY REPRODUCTION OR USE IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF WOOD STONE IS
PROHIBITED
AN ONGOING PROGRAM OF PRODUCT IMPROVEMENT
MAY REQUIRE US TO CHANGE SPECIFICATIONS
WITHOUT NOTICE.
DATE:
G
120VAC, 4A
GAS INLET: 1" NPT
225,000 BTU, NG
225,000 BTU, LP
1 of 1
G
G
57 3/4"
1470mm
53 3/4"
1370mm
10"
250mm
12"
300mm OD
95 3/4"
2430mm
48 1/4"
1230mm
37 1/2"
950mm
14"
360mm
9 3/4"
250mm
10 1/4"
260mm
33 3/4"
860mm
24 3/4"
630mm
25 1/2"
650mm
77 3/4"
1970mm
2"
50mm
57 1/2"
1460mm
10"
250mm
AIR INTAKE
6"
150mm
29 3/4"
760mm
33 3/4"
860mm
67 1/4"
1710mm
7 1/2"
190mm
7 1/4"
180mm
19"
480mm
13 1/2"
340mm
1"
30mm
1 1/2"
40mm
Air intake: Do not
facade or cover over
Must be left
removable for service
NOTE: Using the temporary optional casters will
add 3" to the total height of the oven, for a total
of 82-1/2"�

9
9660 & 11260 Fire Deck Coal-Fired Oven
Installation and Operation Manual
Plan view
Front view
11260-CL SPECIFICATIONS
UTILITY SPECIFICATIONS
Gas: 1" FNPT gas inlet
225,000 BTU/hr Natural Gas (NG)
OR
225,000 BTU/hr Propane (LP)
Venting
This oven may be vented with a Listed Type 1 exhaust hood OR directly connected
at the 12-inch O�D� oven flue collar to a power-ventilated, grease-rated chimney OR
an exhaust hood constructed in accordance with NFPA 96 and all relevant local and
national codes� The oven must be vented in accordance with all relevant local and
national codes, and in a manner acceptable to the authority having jurisdiction�
IMPORTANT: This model must be vented as a solid fuel appliance�
Electrical
120 VAC, 4 A, 50/60 Hz
Utility connections made
on left side of oven as
shown�
Unit weight:
6,415 lbs
Shipping weight:
6,800 lbs.
REV:
LEGEND:
PART #:
FD-11260
11260 Fire Deck
General Arrangement
9/18/2013 bena
1
DWN BY:
SHEET:
Bellingham, WA 360/650-1111 www.woodstone-corp.com
DIMENSIONS ARE IN INCHES
TOLERANCES: LINEAR ±1/2 [±10mm], ANGULAR ±2°
UNLESS NOTED OTHERWISE
\\woodstone.net\dfs\CAD\0 Pn\WS Top Level\FD-11260-CL_General Arrangement-1.dft
THE INFORMATION CONTAINED IN THIS DRAWING IS THE
SOLE PROPERTY OF WOOD STONE CORPORATION
ANY REPRODUCTION OR USE IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF WOOD STONE IS
PROHIBITED
AN ONGOING PROGRAM OF PRODUCT IMPROVEMENT
MAY REQUIRE US TO CHANGE SPECIFICATIONS
WITHOUT NOTICE.
DATE:
G
120VAC, 4A
GAS INLET: 1" NPT
225,000 BTU, NG
225,000 BTU, LP
1 of 1
AIR INTAKE
G
G
67 1/4"
1710mm
7 1/2"
190mm
57 3/4"
1470mm
7"
180mm
79 1/2"
2020mm
9 3/4"
250mm
25 1/2"
650mm
24 3/4"
630mm
9 3/4"
250mm
14"
360mm
111 1/2"
2830mm
4 1/2"
120mm
53 3/4"
1370mm
2"
50mm 1"
30mm
48 1/4"
1230mm
29 3/4"
760mm
9 1/4"
230mm
38"
970mm
57 1/2"
1460mm
13 1/2"
340mm
19"
480mm
33 3/4"
850mm
77 3/4"
1970mm
12"
300mm OD
6"
150mm
1 1/2"
40mm
111 3/4"
2840mm
Model shown: WS-FD-11260-RFG-L-CL
An ongoing program of product improvement may require us to change
specifications without notice. FD-9660-CL, FD-11260-CL,
Revised November 2015. Doc no: M0044.03
[email protected] or visit woodstone-corp.com
Wood Stone Corporation
1801 W. Bakerview Rd.
Bellingham, WA 98226 USA
Toll Free 800.988.8103
Tel [phone]
Fax [phone]
NOTE: Using the temporary optional casters
will add 3" to the total height of the oven,
for a total of 82-1/2"�
REV:
LEGEND:
PART #:
FD-11260
11260 Fire Deck
General Arrangement
9/18/2013 bena
1
DWN BY:
SHEET:
Bellingham, WA 360/650-1111 www.woodstone-corp.com
DIMENSIONS ARE IN INCHES
TOLERANCES: LINEAR ±1/2 [±10mm], ANGULAR ±2°
UNLESS NOTED OTHERWISE
\\woodstone.net\dfs\CAD\0 Pn\WS Top Level\FD-11260-CL_General Arrangement-1.dft
THE INFORMATION CONTAINED IN THIS DRAWING IS THE
SOLE PROPERTY OF WOOD STONE CORPORATION
ANY REPRODUCTION OR USE IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF WOOD STONE IS
PROHIBITED
AN ONGOING PROGRAM OF PRODUCT IMPROVEMENT
MAY REQUIRE US TO CHANGE SPECIFICATIONS
WITHOUT NOTICE.
DATE:
G
120VAC, 4A
GAS INLET: 1" NPT
225,000 BTU, NG
225,000 BTU, LP
1 of 1
AIR INTAKE
G
G
67 1/4"
1710mm
7 1/2"
190mm
57 3/4"
1470mm
7"
180mm
79 1/2"
2020mm
9 3/4"
250mm
25 1/2"
650mm
24 3/4"
630mm
9 3/4"
250mm
14"
360mm
111 1/2"
2830mm
4 1/2"
120mm
53 3/4"
1370mm
2"
50mm 1"
30mm
48 1/4"
1230mm
29 3/4"
760mm
9 1/4"
230mm
38"
970mm
57 1/2"
1460mm
13 1/2"
340mm
19"
480mm
33 3/4"
850mm
77 3/4"
1970mm
12"
300mm OD
6"
150mm
1 1/2"
40mm
111 3/4"
2840mm
REV:
LEGEND:
PART #:
FD-11260
11260 Fire Deck
General Arrangement
9/18/2013 bena
1
DWN BY:
SHEET:
Bellingham, WA 360/650-1111 www.woodstone-corp.com
DIMENSIONS ARE IN INCHES
TOLERANCES: LINEAR ±1/2 [±10mm], ANGULAR ±2°
UNLESS NOTED OTHERWISE
\\woodstone.net\dfs\CAD\0 Pn\WS Top Level\FD-11260-CL_General Arrangement-1.dft
THE INFORMATION CONTAINED IN THIS DRAWING IS THE
SOLE PROPERTY OF WOOD STONE CORPORATION
ANY REPRODUCTION OR USE IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF WOOD STONE IS
PROHIBITED
AN ONGOING PROGRAM OF PRODUCT IMPROVEMENT
MAY REQUIRE US TO CHANGE SPECIFICATIONS
WITHOUT NOTICE.
DATE:
G
120VAC, 4A
GAS INLET: 1" NPT
225,000 BTU, NG
225,000 BTU, LP
1 of 1
AIR INTAKE
G
G
67 1/4"
1710mm
7 1/2"
190mm
57 3/4"
1470mm
7"
180mm
79 1/2"
2020mm
9 3/4"
250mm
25 1/2"
650mm
24 3/4"
630mm
9 3/4"
250mm
14"
360mm
111 1/2"
2830mm
4 1/2"
120mm
53 3/4"
1370mm
2"
50mm 1"
30mm
48 1/4"
1230mm
29 3/4"
760mm
9 1/4"
230mm
38"
970mm
57 1/2"
1460mm
13 1/2"
340mm
19"
480mm
33 3/4"
850mm
77 3/4"
1970mm
12"
300mm OD
6"
150mm
1 1/2"
40mm
111 3/4"
2840mm
Air intake: Do not
facade or cover over
Must be left
removable for service
Side view

10
9660 & 11260 Fire Deck Coal-Fired Oven
Installation and Operation Manual
PLACING AND INSTALLATION
PLACING THE OVEN
The oven must be installed on a flat level surface� The weight of the oven is carried by the full perimeter of the oven stand� If it is
necessary to shim the oven for leveling purposes, it is critical that the shim material be metal, and that the shims are installed in such
a way that the full perimeter of the stand is solidly supported� Any gaps created by shimming between the oven and the floor must be
sealed to prevent airflow issues beneath the oven� Failure to solidly support the full perimeter of the oven stand can result in
costly damage to the oven and will void the warranty.
The floor design and construction must be adequate to handle the weight of the oven�
Please see woodstone-corp.com/installation_footprints.htm for floor loading information�
TOE KICK AND FORK POCKET COVERS
FORK POCKET
COVER
INSTALLATION
Toe kick
Fork pocket covers
(Both sides & rear)
Fork pocket covers
(Both sides & rear)
Once the oven is in place, the Toe Kick must be installed along the front of the oven using the screws provided� Additionally, the side
are rear Fork Pocket Covers must be installed the fork pockets for the oven to operate safely. The area under the oven must
be enclosed in order to prevent pests from entering this space and to prevent air flow issues which can detrimentally effect Burner
operation�
If the front of the oven is shipped facade ready, the Toe Kick will not be included� If the sides and/or rear of the oven is shipped facade
ready, the Fork Pocket Covers will not be included� Pre-cut blocks of cement board or other facade material will be shipped instead of
the Fork Pocket Covers� The blocks must be inserted into the Fork Pockets before the oven facade is put in place�
L1217
ATTENTION INSTALLER
Fork Pocket Cover
MUST be installed
over pocket for oven
to operate properly.
L1217
ATTENTION INSTALLER
Fork Pocket Cover
MUST be installed
over pocket for oven
to operate properly.
L1217
ATTENTION INSTALLER
Fork Pocket Cover
MUST be installed
over pocket for oven
to operate properly.
L1217
ATTENTION INSTALLER
Fork Pocket Cover
MUST be installed
over pocket for oven
to operate properly.
L1217
ATTENTION INSTALLER
Fork Pocket Cover
MUST be installed
over pocket for oven
to operate properly.
L1217
ATTENTION INSTALLER
Fork Pocket Cover
MUST be installed
over pocket for oven
to operate properly.
L1217
ATTENTION INSTALLER
Fork Pocket Cover
MUST be installed
over pocket for oven
to operate properly.
L1217
ATTENTION INSTALLER
Fork Pocket Cover
MUST be installed
over pocket for oven
to operate properly.
REAR FORK POCKETS
Pocket covers
arrive
fastened in
temporary UP
position.
Unfasten, lower
over each fork
pocket, and
refasten.
Ü
L1217
ATTENTIONINSTALLER
ForkPocket Cover
MUSTbe installed
overpocket for oven
tooperate properly.
L1217
ATTENTIONINSTALLER
ForkPocket Cover
MUSTbe installed
overpocket for oven
tooperate properly.
L1217
ATTENTION INSTALLER
Fork Pocket Cover
MUST be installed
over pocket for oven
to operate properly.
L1217
ATTENTION INSTALLER
Fork Pocket Cover
MUST be installed
over pocket for oven
to operate properly.
L1217
ATTENTION INSTALLER
Fork Pocket Cover
MUST be installed
over pocket for oven
to operate properly.
L1217
ATTENTION INSTALLER
Fork Pocket Cover
MUST be installed
over pocket for oven
to operate properly.
L1217
ATTENTION INSTALLER
Fork Pocket Cover
MUST be installed
over pocket for oven
to operate properly.
L1217
ATTENTION INSTALLER
Fork Pocket Cover
MUST be installed
over pocket for oven
to operate properly.
L1217
ATTENTIONINSTALLER
ForkPocket Cover
MUSTbe installed
overpocket for oven
tooperate properly.
L1217
ATTENTIONINSTALLER
ForkPocket Cover
MUSTbe installed
overpocket for oven
tooperate properly.
L1217
ATTENTION INSTALLER
Fork Pocket Cover
MUST be installed
over pocket for oven
to operate properly.
L1217
ATTENTION INSTALLER
Fork Pocket Cover
MUST be installed
over pocket for oven
to operate properly.
L1217
ATTENTION INSTALLER
Fork Pocket Cover
MUST be installed
over pocket for oven
to operate properly.
L1217
ATTENTION INSTALLER
Fork Pocket Cover
MUST be installed
over pocket for oven
to operate properly.
L1217
ATTENTION INSTALLER
Fork Pocket Cover
MUST be installed
over pocket for oven
to operate properly.
L1217
ATTENTION INSTALLER
Fork Pocket Cover
MUST be installed
over pocket for oven
to operate properly.
GAS INLET SIDE FORK POCKETS
Unfasten,
place one cover
over each fork
pocket, and
refasten.
Two pocket covers
will arrive fastened in
temporary UP
position above front-
most fork pocket.
ÜÜ
L1217
ATTENTIONINSTALLER
ForkPocket Cover
MUSTbe installed
overpocket for oven
tooperate properly.
L1217
ATTENTIONINSTALLER
ForkPocket Cover
MUSTbe installed
overpocket for oven
tooperate properly.
L1217
ATTENTION INSTALLER
Fork Pocket Cover
MUST be installed
over pocket for oven
to operate properly.
L1217
ATTENTION INSTALLER
Fork Pocket Cover
MUST be installed
over pocket for oven
to operate properly.
L1217
ATTENTION INSTALLER
Fork Pocket Cover
MUST be installed
over pocket for oven
to operate properly.
L1217
ATTENTION INSTALLER
Fork Pocket Cover
MUST be installed
over pocket for oven
to operate properly.
L1217
ATTENTION INSTALLER
Fork Pocket Cover
MUST be installed
over pocket for oven
to operate properly.
L1217
ATTENTION INSTALLER
Fork Pocket Cover
MUST be installed
over pocket for oven
to operate properly.
NON-GAS INLET SIDE FORK POCKETS
Pocket covers
arrive
fastened in
temporary UP
position.
Unfasten, lower
over each fork
pocket, and
refasten.
Ü
Note: Additional
Tek screws
supplied in
hardware kit.