Woodendot Alba L User manual

ASSEMBLY INSTRUCTIONS
Alba L

2 DIFFERENT POSSIBILITIES
4 DIFFERENT POSSIBILITIES
1x OR
1x 1x 1x 1x
6x 1x1x
7x 11x
(A) (D) (B) (C) (E)
1x
You will need a manual drill
for the wall holes
We recommend two people
for the installation
For the hole to be the exact depth, measure 50mm/1.96”
on the drill bit and place tape around it to mark the
distance. Stop drilling when it reaches that depth.
The drill bit required is Ø 6 mm or 15/64”
Depth of the hole in wall: 50 mm / 1.96”

1º
Use the level tool
Mark the holes with a pencil
(A)
2º 4º
3º
(B)
Place the “U” piece between the wall
and the back panel.
Mark the three holes with a pencil
5º
6º
7º
8º
Screw the “U” piece to the back panel
(x2 screws)
(C)
Make the hole in the wall
9º
(A)
10º
11º
Screw the “U” piece to the wall
with the help of the Allen key
Screw the table cover
13º
12º
(E)
(D)

14º
Introduce the small
wooden piece
15º
Make a line at the intersection of the
small piece of wood on the back.
16º Take out the small
wooden piece
Screw on the L-shaped metal
piece using the marked line
17º
(C)
18º Introduce the small wooden piece with
the metal piece towards the back. Screw to the set
19º
(C)

ASSEMBLY INSTRUCTIONS
Alba L

1x OR
1x
1x
1x 1x 1x
2 DIFFERENT POSSIBILITIES
4 DIFFERENT POSSIBILITIES
6x 1x1x
7x 11x
(A) (D) (B) (C) (E)
You will need a manual drill
for the wall holes
We recommend two people
for the installation
For the hole to be the exact depth, measure 50mm/1.96”
on the drill bit and place tape around it to mark the
distance. Stop drilling when it reaches that depth.
The drill bit required is Ø 6 mm or 15/64”
Depth of the hole in wall: 50 mm / 1.96”

1º 2º
4º
3º
Place the “U” piece between the wall
and the back panel.
Mark the three holes with a pencil
5º
6º
7º
8º
Make the hole in the wall
9º
10º
11º
Screw the “U” piece to the wall
with the help of the Allen key
Screw the table cover
13º
12º
Use the level tool
Mark the holes with a pencil
(A)
(B)
(A)
(E)
(D)
(C)
Screw the “U” piece to the back panel
(x2 screws)

ASSEMBLY INSTRUCTIONS
Alba L

1x OR
1x
1x
8 DIFFERENT POSSIBILITIES
4 DIFFERENT POSSIBILITIES
1x 1x 1x
6x
1x1x
7x 11x
(A)
(D)
(B) (C)
(E) (F)
2x
You will need a manual drill
for the wall holes
We recommend two people
for the installation
For the hole to be the exact depth, measure 50mm/1.96”
on the drill bit and place tape around it to mark the
distance. Stop drilling when it reaches that depth.
The drill bit required is Ø 6 mm or 15/64”
Depth of the hole in wall: 50 mm / 1.96”

6º
7º
Make the hole in the wall
9º
11º
12º
Screw the “U” piece to the wall
with the help of the Allen key
Screw the table cover
5º
3º
4º
8º
13º
(A)
(E)
(D)
14º
(C)
(C)
1º
Use the level tool
Mark the holes with a pencil
2º
(A)
(B)
Place the double-sided
adhesives (x2) on the metal flap
10º
(F)
Screw the “U” piece to the back panel
(x2 screws)
Place the “U” piece between the wall
and the back panel.
Mark the three holes with a pencil

15º
Introduce the small
wooden piece 16º
Make a line at the intersection of the
small piece of wood on the back.
Screw on the L-shaped metal
piece using the marked line
18º
17º
Take out the small
wooden piece
(C)
19º
Introduce the small wooden piece with
the metal piece towards the back. Screw to the set
18º

16º Take out the small
wooden piece
14º
Introduce the small
wooden piece 15º
Make a line at the intersection of the
small piece of wood on the back.
Screw on the L-shaped metal
piece using the marked line
17º
18º
Introduce the small wooden piece with
the metal piece towards the back.
Screw to the set
19º
(C)
(C)

ASSEMBLY INSTRUCTIONS
Alba L

1x OR
1x
1x
1x
6x
1x1x
7x 11x
(A)
(D)
(B) (C)
(E)
1x 1x
(F)
2x
8 DIFFERENT POSSIBILITIES
4 DIFFERENT POSSIBILITIES
You will need a manual drill
for the wall holes
We recommend two people
for the installation
For the hole to be the exact depth, measure 50mm/1.96”
on the drill bit and place tape around it to mark the
distance. Stop drilling when it reaches that depth.
The drill bit required is Ø 6 mm or 15/64”
Depth of the hole in wall: 50 mm / 1.96”

1º
Use the level tool
Mark the holes with a pencil
2º
3º
4º
(A)
(B)
5º
6º
7º
8º
Make the hole in the wall
9º (A)
Place the double-sided
adhesives (x2) on the metal flap
10º
11º
12º
(F)
Screw the “U” piece to the wall
with the help of the Allen key
Screw the table cover
13º
(E)
(D)
14º
(C)
(C)
Screw the “U” piece to the back panel
(x2 screws)
Place the “U” piece between the wall
and the back panel.
Mark the three holes with a pencil

15º Introduce the small
wooden piece
16º
Make a line at the intersection of the
small piece of wood on the back.
Take out the small
wooden piece
17º
Screw on the L-shaped metal
piece using the marked line
18º
(C)
19º
Introduce the small wooden piece with
the metal piece towards the back.
Screw to the set
and finish
18º