Woodland Mills MULTILANDER TRAILER User manual

!
MULTILANDER™TRAILER
OPERATOR’S MANUAL
0008127-M-EN: Rev B Publication Date: 24-Feb-2023
Multilander™is a trademark of Woodland Mills, Inc.

!
This page intentionally left blank.

Multilander™Operator’s Manual
TABLE OF CONTENTS
TABLE OF CONTENTS __________________________________________________1
INTRODUCTION ________________________________________________________3
GENERAL SAFETY RULES_______________________________________________4
INSPECTION/MAINTENANCE _____________________________________________4
TECHNICAL SPECIFICATIONS____________________________________________5
OVERALL DIMENSIONS ______________________________________________6
COMPONENT LISTS ____________________________________________________7
TO-SCALE HARDWARE_______________________________________________9
BOLTS & SCREWS __________________________________________________9
SCALES __________________________________________________________11
WASHERS ________________________________________________________12
NUTS_____________________________________________________________13
TOOLS REQUIRED ____________________________________________________14
BOLT TORQUE________________________________________________________15
CHASSIS ASSEMBLY __________________________________________________16
1. FRAME ________________________________________________________16
TONGUE ORIENTATION ____________________________________________17
2. AXLE CROSS BEAM______________________________________________19
3. WALKING BEAMS________________________________________________20
4. WHEELS _______________________________________________________21
5. SWIVEL JACK ___________________________________________________22
6. COUPLER ______________________________________________________24
7. BUMPERS ______________________________________________________25
UTILITY BOX ASSEMBLY _______________________________________________26
1. FRAME ________________________________________________________26
2. STEPPED SIDES ________________________________________________28
3. PICKUP ________________________________________________________31
4. UTILITY BOX-TO-CHASSIS ________________________________________32
5. BRACKETRY____________________________________________________33
6. SIDE PANELS ___________________________________________________36
7. TAILGATES _____________________________________________________38
8. LOG LOADING RAMP LEG ________________________________________40
0008127-M-EN: Rev B
Page of164
24-Feb-2023

Multilander™Operator’s Manual
WINCH AND BOOM ASSEMBLY __________________________________________41
1. WINCH POST ___________________________________________________41
2. BOOM _________________________________________________________43
3. WINCH ROPE ___________________________________________________45
OPERATION __________________________________________________________46
MAINTENANCE _______________________________________________________52
GREASE POINTS ___________________________________________________52
REPLACEMENT PARTS ORDERING ______________________________________53
EXPLODED ASSEMBLY VIEWS __________________________________________54
CHASSIS__________________________________________________________54
WHEELS __________________________________________________________55
WINCH ___________________________________________________________56
BOOM & RAMP LEG_________________________________________________57
UTILITY BOX: BED __________________________________________________58
UTILITY BOX: BRACKETRY___________________________________________59
UTILITY BOX: SIDE PANELS __________________________________________60
UTILITY BOX: TAILGATES ____________________________________________61
PARTS LIST __________________________________________________________62
NOTES ______________________________________________________________64
0008127-M-EN: Rev B
Page of264
24-Feb-2023

Multilander™Operator’s Manual
INTRODUCTION
Congratulations on your purchase and welcome to Woodland Mills! This manual gives you the
necessary information about your Multilander™trailer so you will be able to use it properly. The
entire manual must be read and understood prior to using the trailer. If any questions arise not
covered by this manual, please contact Woodland Mills, Inc.
The Multilander™is a utility trailer designed to be towed behind tractors, RTVs, and ATVs for off-
road use.
The Multilander™ trailer is designed for certain off-road applications only. We strongly
recommend the trailer not be modified and/or used for any application other than that for which
it was designed. If you have any questions relative to a particular application, DO NOT use the
trailer until you have first contacted Woodland Mills to determine if it can or should be performed
using the product.
For technical questions and replacement parts, please contact Woodland Mills, Inc.
OWNER'S RECORD
Please take a moment to record the following information about your
Multilander™ trailer. If you need to call for assistance, please be ready to
provide your model and serial numbers. You will find this information
located on the underside of the trailer chassis. This information will allow us
to help you more quickly when you call.
MODEL NUMBER
SERIAL NUMBER
DATE OF PURCHASE
0008127-M-EN: Rev B
Page of364
24-Feb-2023

Multilander™Operator’s Manual
**SAVE THESE INSTRUCTIONS**
GENERAL SAFETY RULES
INSPECTION/MAINTENANCE
•Check the tires before all trips. Make sure they are inflated to the pressure shown on the tire.
•Grease the axle bearings and walking beams every 3 months or 100 hours, whichever comes
first.
•Check the tow hitch ball coupler. Make sure it is not damaged.
•Check the wheel lug nuts before all trips. Make sure they are torqued properly.
•Inspect trailer before all trips for any damaged or loose parts.
0008127-M-EN: Rev B
Page of464
24-Feb-2023
Read and understand all instructions. Failure to follow all instructions
listed below may result serious injury.
WARNING!
The warnings, cautions, and instructions discussed in this instruction
manual cannot cover all possible conditions or situations that could
occur. It must be understood by the operator that common sense and
caution are factors which cannot be built into this product but must be
supplied by the operator.
WARNING!

Multilander™Operator’s Manual
TECHNICAL SPECIFICATIONS
Item
Specification
Construction/Finish
Powder-Coated/Galvanized Tube & Plate Steel
Axle
Walking Beam
Wheels & Tires
4 Bolts @ 4” [101.6 mm] & 23x10.5-12 Tires
Tire Pressure
Refer to Tire
Wheel Nut Torque
80 ft•lb [110 N•m]
Trailer Ball Coupler
2 in [50 mm]
Hauling Capacity
2000 lb [907 kg]
Log Winch Capacity
2000 lb [907 kg]
Overall Length
133-1/16 in [3379 mm]
Overall Width
47-⅞in [1216 mm]
Overall Height
62-5/16 in [1582 mm] MIN to 80-5/16 in [2039 mm] MAX
Utility Box Volume
1.18 yd3[0.9 m3]
Utility Box Dump Angle
50° MAX (from horizontal @ maximum boom extension)
Product Weight
685 lb [311 kg]
Shipping Weight
826 lb [375 kg]
0008127-M-EN: Rev B
Page of564
24-Feb-2023
Left
Right
Rear
Front

Multilander™Operator’s Manual
OVERALL DIMENSIONS!
0008127-M-EN: Rev B
Page of664
24-Feb-2023













Multilander™Operator’s Manual
COMPONENT LISTS
Verify all component and hardware quantities are correct prior to assembling the trailer.
2x
Chassis Side
Rail
[0008131]
2x
2x
Right Wheel
[22X11-10R]
Left Wheel
[22X11-10L]
1x
Tongue
[0008135]
1x
Swivel Jack
Mount
[0002249]
1x
Bottom Tongue
Plate
[0008134]
1x
Swivel Jack
Handle Mount
[0008314]
1x
Top Tongue
Plate
[0008132]
1x
Swivel Jack
[0006798]
1x
Brace Storage
Bracket
[0008316]
1x
Swivel Jack
Handle
Assembly
1x
Axle Cross
Beam
[0008159]
1x
Winch Brace
[0008209]
2x
Walking Beam
Assembly
5x
Square Locking
Pin - 12 mm Dia
[0004704]
4x
Nylon Spacer
30.5 X 50 X 3
[0004384]
1x
Hitch Ball
Coupler
[0001381]
2x
Spacer
24.5 X 50 X 4
[0004274]
1x
Round Locking
Pin
[0004728]
2x
Cotter Pin
[0004753]
2x
Rubber Bumper
[0008139]


























































































0008127-M-EN: Rev B
Page of764
24-Feb-2023

Multilander™Operator’s Manual
1x
Left Lower
Beam
[0008138]
2x
Side Panel
[0008709]
1x
Right Lower
Beam
[0008137]
4x
Side Panel
Hinge
[0008699]
3x
Support Rib
[0007156]
4x
Indexer
[0008706]
1x
Bed Panel
[0007124]
4x
Spacer
10 X 16 X 8
[0008711]
2x
Stepped Side
Panel
[0007126]
4x
Hook Latch
[0002338]
4x
Hinge Block
[0008707]
2x
Tailgate
Assembly
2x
Spacer
8 X 12 X 48
[0008143]
1x
Boom
Assembly
1x
Pickup
[0008723]
1x
Log Loading
Ramp Leg
Assembly
4x
Bumper Bracket
Assembly
1x
Clevis Pin
[0004321]
2x
Ramp Storage
Bracket
Assembly*
1x
Hairpin Cotter
Pin
[0004706]
2x
Winch Bracket
[0008296]
1x
Winch Post
[0008196]




































































































































0008127-M-EN: Rev B
Page of864
24-Feb-2023

Multilander™Operator’s Manual
TO-SCALE HARDWARE
BOLTS & SCREWS
Hardware graphics are printed at 1:1 scale for ease of identification. Simply place the hardware
over the image in the tables to verify it is the correct size.
1x
Winch and
Rope Assembly
*The Ramp Storage Bracket Assemblies
may ship assembled to the Log Loading
Ramp Leg in the crate.
1x
HHB-MBJ115PCJ
M8 X 1.25 X 60 mm HEX BOLT
7x
HHB-MBJ120PCJ
M8 X 1.25 X 65 mm HEX BOLT
1x
HHB-MBJ125PCJ
M8 X 1.25 X 70 mm HEX BOLT
6x
HHB-MBM080FCJ
M10 X 1.5 X 25 mm HEX BOLT
2x
HHB-MBM145PCJ
M10 X 1.5 X 90 mm HEX BOLT
0008127-M-EN: Rev B
Page of964
24-Feb-2023

Multilander™Operator’s Manual
1x
HHB-MBR090FCJ
M12 X 1.75 X 35 mm HEX BOLT
2x
HHB-MBR130PCJ
M12 X 1.75 X 75 mm HEX BOLT
12x
HHB-MBR145PCJ
M12 X 1.75 X 90 mm HEX BOLT
8x
BHS-MBE063FCM
M6 X 1 X 12 mm BUTTON HEAD SCREW
2x
BHS-MBE135FCM
M6 X 1 X 80 mm BUTTON HEAD SCREW
14x
BHS-MBJ067FCM
M8 X 1.25 X 14 mm BUTTON HEAD SCREW
12x
BHS-MBJ115FCM
M8 X 1.25 X 60 mm BUTTON HEAD SCREW
0008127-M-EN: Rev B
Page of10 64
24-Feb-2023

Multilander™Operator’s Manual
SCALES
Ruler scales are also provided below to double-check bolt and screw lengths when necessary.
6x
BHS-MBJ155FCM
M8 X 1.25 X 100 mm BUTTON HEAD SCREW
2x
BHS-MBM110PCM
M10 X 1.5 X 55 mm BUTTON HEAD SCREW
2x
BHS-MBM115PCM
M10 X 1.5 X 60 mm BUTTON HEAD SCREW
4x
HFH-MBM115PCM
M10 X 1.5 X 60 mm FLAT HEAD SCREW
8x
HFH-MBM125PCM
M10 X 1.5 X 70 mm FLAT HEAD SCREW
0008127-M-EN: Rev B
Page of11 64
24-Feb-2023

Multilander™Operator’s Manual
WASHERS
4x
FTW-MBE000AJ
M6 FLAT WASHER
50x
FTW-MBJ000AJ
M8 FLAT WASHER
24x
FTW-MBM000AJ
M10 FLAT WASHER
30x
FTW-MBR000AJ
M12 FLAT WASHER
4x
FTW-MCC000AJ
M18 FLAT WASHER
4x
FDW-MBM083000AJ
M10 X 34 mm FENDER WASHER
0008127-M-EN: Rev B
Page of12 64
24-Feb-2023

Multilander™Operator’s Manual
NUTS
10x
HLN-MBECH
M6 X 1 LOCK NUT
41x
HLN-MBJCH
M8 X 1.25 LOCK NUT
20x
HLN-MBMCH
M10 X 1.5 LOCK NUT
15x
HLN-MBRCH
M12 X 1.75 LOCK NUT
2x
HLN-MCCCH
M18 X 2.5 LOCK NUT*
8x
0006202
M12 X 1.5 LUG NUT
2x
0006092
M24 X 1.5 SLOTTED LOCK NUT
0008127-M-EN: Rev B
Page of13 64
24-Feb-2023

Multilander™Operator’s Manual
TOOLS REQUIRED
Tool
Specification
Wrench/Socket
10 mm
Wrench/Socket
13 mm
Wrench/Socket
16 mm
Wrench/Socket
17 mm
Wrench/Socket
18 mm
Wrench/Socket
19 mm
Wrench/Socket
27 mm
Adjustable Wrench
Variable
Hex Key
4 mm
Hex Key
5 mm
Pliers
Needle Nose, Lineman’s, or Slip-Joint
Torque Wrench
Capable of 80 ft•lb (109 N•m)
Packing Grease
Multipurpose Grease
0008127-M-EN: Rev B
Page of14 64
24-Feb-2023

Multilander™Operator’s Manual
BOLT TORQUE
0008127-M-EN: Rev B
Page of15 64
24-Feb-2023
Deformed
tubing = bad
DO NOT TORQUE TO SPEC WHEN BOLTING
THROUGH TUBING. SNUG HARDWARE,
THEN TIGHTEN A FURTHER ¼—½TURN.
When assembling the trailer, do not torque the bolts to hardware
Class/Grade specifications. Snug the hardware, then tighten a further
¼—½turn. Tightening bolts to torque spec can crush metal tubing,
ruining the components.
BOLT TORQUE WARNING!

Multilander™Operator’s Manual
CHASSIS ASSEMBLY
1. FRAME
Using the components and hardware listed below, assemble the chassis side rails to the
tongue .
The chassis side rails are connected to the tongue via the top and bottom tongue plates. It is
important to know the height of the tow vehicle hitch prior to starting the assembly so that the
tongue can be oriented to suit. See section, Tongue Orientation, on the next page.
8x
M12 X 90 mm
Hex Bolt
2x
Chassis Side
Rail
15x
M12 Flat
Washer
1x
Ton gu e
8x
M12 Lock Nut
1x
Bottom Tongue
Plate
1x
Top Tongue
Plate
1x
Brace Storage
Bracket
















































0008127-M-EN: Rev B
Page of16 64
24-Feb-2023
See Tongue
Orientation section
on next page

Multilander™Operator’s Manual
TONGUE ORIENTATION
When the hitch ball coupler is assembled to the tongue in
a later step, it will become a 360° rotating ball hitch (see
right).
The tongue can be used with the hitch ball coupler
positioned above the tongue or below the tongue (see
graphics below). This helps keep the trailer level based
on the towing vehicle’s ball height measured from the
ground.
Prior to assembling the chassis beams to the tongue, first
determine which coupler mounting style is best suited to
the tow vehicle as shown in the graphics below.
With the Below the Tongue style, the tongue is flipped 180° so that the rotating ball hitch is on
the bottom.
Once the coupler mounting style is decided upon, continue with the chassis assembly on the
next page. This manual is illustrated using the Above the Tongue style, however, the assembly
steps proceeding the chassis assembly are identical no matter which tongue orientation is used.
0008127-M-EN: Rev B
Page of17 64
24-Feb-2023
17-⅞in
[453 mm]
ABOVE THE TONGUE
13-½in
[343 mm]
BELOW THE TONGUE
Rotating Ball Hitch

Multilander™Operator’s Manual
Lay out the side rails and tongue on a flat surface. It can be beneficial to the assembly process
to build the chassis on blocks or timbers.
Use eight (8) M12 X 90 mm hex bolts, fifteen (15) M12 flat washers, eight (8) M12 lock nuts and
the Brace Storage Bracket to sandwich the rails and tongue between the top and bottom tongue
plates. Do not fully tighten the hardware.
0008127-M-EN: Rev B
Page of18 64
24-Feb-2023
The Brace Storage
Bracket is positioned
under the front bolt
head. Do not use a flat
washer in this location.