Woodland Mills Woodlander User manual

!
WOODLANDER™SAWMILL TRAILER
OPERATOR’S MANUAL
0001361-M-EN: Rev A Publication Date: 01-Dec-2021
The Woodlander™ is compatible with HM126 and HM130 sawmills. Woodlander™is a trademark of Woodland Mills, Inc.

!
This page intentionally left blank.

2017 Woodlander™Operator’s Manual
TABLE OF CONTENTS
TABLE OF CONTENTS ____________________________________________1
INTRODUCTION __________________________________________________2
INTENDED USE __________________________________________________3
TECHNICAL SPECIFICATIONS ______________________________________3
GENERAL SAFETY RULES_________________________________________3
BOLT TORQUE SPECIFICATIONS ___________________________________4
INSPECTION/MAINTENANCE _______________________________________4
SAWMILL TRAILER ASSEMBLY _____________________________________5
1. UNPACKING _______________________________________________5
2. SETUP ____________________________________________________6
REPLACEMENT PARTS ORDERING ________________________________30
EXPLODED ASSEMBLY VIEWS ____________________________________31
CHASSIS AND TRACK _________________________________________31
TONGUE: NORTH AMERICA ____________________________________32
TONGUE: EUROPE____________________________________________32
AXLES, WHEELS, AND FENDERS________________________________33
LIGHTING: NORTH AMERICA ___________________________________34
LIGHTING: EUROPE ___________________________________________35
NAMEPLATES ________________________________________________36
JACKS ______________________________________________________37
HEAD LOCK-DOWN ___________________________________________38
PARTS LISTS ___________________________________________________39
NORTH AMERICA _____________________________________________39
EUROPE ____________________________________________________40
NOTES ________________________________________________________42
0001361-M-EN: Rev A
Page of144
01-Dec-2021

2017 Woodlander™Operator’s Manual
INTRODUCTION
Congratulations on your purchase and welcome to Woodland Mills. This manual gives you the
necessary information about your trailer so you will be able to use it properly. The entire manual
must be read and understood before you start using the trailer. If any questions should arise that
are not covered by this manual, please contact Woodland Mills Inc.
This trailer is designed for certain applications only. We strongly recommend that this trailer is
not modified and/or used for any application other than that for which it was designed. If you
have any questions relative to a particular application, DO NOT use the trailer until you have
first contacted us to determine if it can or should be performed on the product.
For technical questions and replacement parts, please contact Woodland Mills.
OWNER'S RECORD
Please take a moment to record the following information about your sawmill
trailer. If you need to call for assistance, please be ready to provide your
model and serial numbers. This information will allow us to help you more
quickly when you call.
MODEL NUMBER
SERIAL NUMBER
DATE OF PURCHASE
0001361-M-EN: Rev A
Page of244
01-Dec-2021

2017 Woodlander™Operator’s Manual
INTENDED USE
This trailer is designed to hold an HM126 or HM130 sawmill and its track system for sawing logs
while the trailer is stationary and firmly supported on the ground. It is not intended to carry any
additional weight or be used as a utility trailer.
TECHNICAL SPECIFICATIONS
GENERAL SAFETY RULES
SAVE THESE INSTRUCTIONS
ITEM
DESCRIPTION
Wheel Nut Torque
80 ft-lbs / 110 Nm
Tire Size
195/60/14
Tire Pressure
Refer to Tire
Tow Ball Size
2” / 50.8mm
0001361-M-EN: Rev A
Page of344
01-Dec-2021
Read and understand all instructions. Failure to follow all instructions
listed below may result in serious injury or death.
WARNING!
WARNING!
The warnings, cautions, and instructions discussed in this instruction
manual cannot cover all possible conditions or situations that could
occur. It must be understood by the operator that common sense and
caution are factors which cannot be built into this product, but must
be supplied by the operator.

2017 Woodlander™Operator’s Manual
BOLT TORQUE SPECIFICATIONS
INSPECTION/MAINTENANCE
•Check the tires before all trips. Make sure they are inflated to the pressure shown on the
tire.
•Grease the axle bearings every 3 months or 1000 miles (1600km), whichever comes first.
•Check the tow hitch ball coupler. Make sure it is not damaged.
•Check the wheel lug nuts before all trips. Make sure they are torqued properly.
•Check the lights. Make sure all the lights work properly. Replace any lights that do not
work.
•Inspect trailer before all trips for any damaged or loose parts.
•
ITEM
DESCRIPTION
M5
78 in-lbs / 9 Nm
M6
133 in-lbs / 15 Nm
M8
333 in-lbs / 38 Nm
M10
53 ft-lbs / 72 Nm
M12
93 ft-lbs / 126 Nm
0001361-M-EN: Rev A
Page of444
01-Dec-2021

2017 Woodlander™Operator’s Manual
SAWMILL TRAILER ASSEMBLY
1. UNPACKING
Remove all the parts from the steel crate. You will use the steel crate in step 2.
0001361-M-EN: Rev A
Page of544
01-Dec-2021

2017 Woodlander™Operator’s Manual
2. SETUP
Using the hardware listed below, build the track with the gussets as shown on the next page.
Make sure the track width is 30.5” (775 mm) and measure diagonally for squareness. Tighten
all the bolts to the specified torque specification.!
0001361-M-EN: Rev A
Page of644
01-Dec-2021
24x
M10 x 30mm Bolt
8x
M10 x 35mm Bolt
32x
Flange Lock Nut
2x
End Bunk
1x
Joining Bunk
2x
Middle Bunk
2x
Joining Plate
4x
End Gusset
6x
Joining Gusset
4x
Track Rail
Use the fasteners that are
included with the sawmill
trailer to assemble the
track. The fasteners that are
included with the sawmill
tracks will not be used.
!

2017 Woodlander™Operator’s Manual
Above steps to be completed to both sides of the track. Make sure the gussets are flush to the
outside of the track rails as shown below.
0001361-M-EN: Rev A
Page of744
01-Dec-2021
Flush
Flush
1x - End Bunk
4x - M10 x 30mm
4x - M10 Lock Nut
2x - End Gusset
1x - Joining Bunk
8x - M10 x 30mm
8x - M10 x 35mm
16x - M10 Lock Nut
2x - Joining Gusset
2x - Joining Plate
1x - Middle Bunk
4x - M10 x 30mm
4x - M10 Lock Nut
2x - Joining Gusset
1x - End Bunk
4x - M10 x 30mm
4x - M10 Lock Nut
2x - End Gusset
1x - Middle Bunk
4x - M10 x 30mm
4x - M10 Lock Nut
2x - Joining Gusset

2017 Woodlander™Operator’s Manual
Place the track assembly on top of the shipping crate making sure it is centred.
Using the hardware listed below, hang the side plates using the M10x25mm and M10x30mm
bolts, do not tighten these bolts. The M10x30mm bolts are used with the track end stop.
Everywhere else uses the M10x25mm bolts.
68x
M10 x 25mm Bolt
8x
M10 x 30mm Bolt
76x
Flange Lock Nut
2x
Long Side Plate
4x
Short Side Plate
4x
Track End Stop
0001361-M-EN: Rev A
Page of844
01-Dec-2021