Woodland Mills Woodlander User manual

!
WOODLANDER™OFF-ROAD
SAWMILL TRAILER
OPERATOR’S MANUAL
0001675-M-EN: Rev C Publication Date: 07-Oct-2022
The Woodlander™and Woodlander™MAX are off-road only sawmill trailers compatible with HM126, HM130 & HM130MAX sawmills.
Woodlander™is a trademark of Woodland Mills, Inc.
*Track Not Included

!
This page intentionally left blank.

2018-2023 Woodlander™(MAX) Operator’s Manual
TABLE OF CONTENTS
TABLE OF CONTENTS __________________________________________________1
INTRODUCTION ________________________________________________________3
GENERAL SAFETY RULES_______________________________________________4
INSPECTION/MAINTENANCE _____________________________________________5
TECHNICAL SPECIFICATIONS____________________________________________6
BOLT TORQUE SPECIFICATIONS _______________________________________6
UNPACKING ___________________________________________________________7
COMPONENT LISTS ____________________________________________________8
TO-SCALE HARDWARE ______________________________________________10
BOLTS & SCREWS ___________________________________________________10
SCALES_____________________________________________________________12
WASHERS___________________________________________________________12
NUTS _______________________________________________________________13
SAWMILL COMPONENTS_____________________________________________14
SAWMILL HARDWARE________________________________________________14
TRAILER ASSEMBLY __________________________________________________15
1. TOOLS REQUIRED _______________________________________________15
2. GUSSETS ______________________________________________________16
3. SIDE PLATES ___________________________________________________18
4. FRONT AND REAR CROSS BEAMS _________________________________21
5. SIDE PLATE-TO-RAIL OFFSET & BOLT TORQUING_____________________23
6. INNER CROSS BEAMS AND JACK MOUNTS __________________________27
7. AXLE MOUNTS AND AXLE CROSS BEAM ____________________________30
8. AXLES _________________________________________________________32
9. TONGUE AND COUPLER __________________________________________34
10. LIGHTING ______________________________________________________36
11. NAMEPLATES ___________________________________________________39
12. HEAD LOCK-DOWN PLATES _______________________________________41
13. WHEELS _______________________________________________________44
WHEEL ALIGNMENT ADJUSTMENT ____________________________________45
14. FENDERS ______________________________________________________46
15. SAFETY CHAIN __________________________________________________48
0001675-M-EN: Rev C
Page of164
07-Oct-2022

2018-2023 Woodlander™(MAX) Operator’s Manual
OPERATION __________________________________________________________49
LOCKING-DOWN THE SAWMILL HEAD _________________________________49
REPLACEMENT PARTS ORDERING ______________________________________51
EXPLODED ASSEMBLY VIEWS __________________________________________52
CHASSIS AND TRACK _______________________________________________52
TONGUE __________________________________________________________53
NORTH AMERICA _________________________________________________53
EUROPE__________________________________________________________53
AXLES, WHEELS, AND FENDERS______________________________________54
LIGHTING _________________________________________________________55
NORTH AMERICA _________________________________________________55
EUROPE__________________________________________________________56
NAMEPLATES ______________________________________________________57
SWIVEL JACKS _____________________________________________________58
HEAD LOCK-DOWN _________________________________________________59
PARTS LISTS _________________________________________________________60
NORTH AMERICA ___________________________________________________60
EUROPE __________________________________________________________62
NOTES ______________________________________________________________64
0001675-M-EN: Rev C
Page of264
07-Oct-2022

2018-2023 Woodlander™(MAX) Operator’s Manual
INTRODUCTION
Congratulations on your purchase and welcome to Woodland Mills! This manual gives you the
necessary information about your Woodlander™sawmill trailer so you will be able to use it
properly. The entire manual must be read and understood before using the trailer. If any
questions should arise that are not covered by this manual, please contact Woodland Mills, Inc.
The Woodlander™sawmill trailer is compatible with HM126, HM130 & HM130MAX sawmill and
track systems for milling logs while the trailer is stationary and firmly supported on the ground.
It is not intended to carry any additional weight or be used as a utility trailer.
The Woodlander™ and Woodlander™MAX sawmill trailers are off-road trailers designed for
certain applications only. We strongly recommend the trailer not be modified and/or used for
any application other than that for which it was designed. If you have any questions relative to a
particular application, DO NOT use the trailer until you have first contacted Woodland Mills to
determine if it can or should be performed using the product.
For technical questions and replacement parts, please contact Woodland Mills, Inc.
"
"
"
"
OWNER'S RECORD
"
"
Please take a moment to record the following information about your
Woodlander™ sawmill trailer. If you need to call for assistance, please be
ready to provide your model and serial numbers. This information will allow
us to help you more quickly when you call.
"
"
"
"
"
MODEL NUMBER
"
"
"
"
"
"
"
"
SERIAL NUMBER
"
"
"
!
"
"
"
"
DATE OF PURCHASE
"
"
"
"
"
"
"
0001675-M-EN: Rev C
Page of364
07-Oct-2022

2018-2023 Woodlander™(MAX) Operator’s Manual
GENERAL SAFETY RULES
0001675-M-EN: Rev C
Page of464
07-Oct-2022
Read and understand all instructions. Failure to follow all instructions
listed below may result serious injury.
WARNING!
The warnings, cautions, and instructions discussed in this instruction
manual cannot cover all possible conditions or situations that could
occur. It must be understood by the operator that common sense and
caution are factors which cannot be built into this product but must be
supplied by the operator.
WARNING!
The trailer is not designed to carry any additional weight other than the
sawmill and trailer itself while being towed. Failure to heed this warning
could result in damage to the trailer and/or the sawmill.
Damage caused by towing additional weight will void the warranty.
WARNING!
The Woodlander™ and Woodlander™MAX sawmill trailers are for off-
road use only. It is the owner’s responsibility to make the trailer
road-worthy if towing on improved roads, complying with all local laws
and regulations.
WARNING!
The Woodlander™ and Woodlander™MAX sawmill
trailers are not designed for speeds exceeding 30
mph [50 km/h].
WARNING!

2018-2023 Woodlander™(MAX) Operator’s Manual
INSPECTION/MAINTENANCE
•Check the tires before all trips. Make sure they are inflated to the pressure shown on the tire.
•Grease the axle bearings every 3 months or 1000 miles [1600 km], whichever comes first.
•Check the tow hitch ball coupler. Make sure it is not damaged.
•Check the wheel lug nuts before all trips. Make sure they are torqued properly.
•Check the lights. Make sure all the lights work properly. Replace any lights that do not work.
•Inspect trailer before all trips for any damaged or loose parts.
0001675-M-EN: Rev C
Page of564
07-Oct-2022

2018-2023 Woodlander™(MAX) Operator’s Manual
TECHNICAL SPECIFICATIONS
BOLT TORQUE SPECIFICATIONS
Item
Specification
Trailer Axle
Independent Torsion Axle Design
Trailer Wheels
5 Bolts @ 4.5 in [114 mm] & 5.30-12 DOT Approved Tires
Tire Pressure
Refer to Tire
Wheel Nut Torque
80 ft•lb [110 N•m]
Trailer Ball Coupler
2 in [50 mm]
Trailer Lights
LED Light Kit (stop, turn, tail, side markers, and license plate light)
Finish
Powder Coat Paint / Galvanized Steel
Fenders
Removable
Safety
Locking pins and safety straps to secure sawhead while travelling
Shipping Weight
Woodlander: 640 lb [290 kg]
Woodlander MAX: 655 lb [297 kg]
Product Weight
Woodlander: 556 lb [252 kg]
Woodlander MAX: 571 lb [259 kg]
Bolt (Thread Size)
Torque
M5
78 in•lb [9 N•m]
M6
133 in•lb [15 N•m]
M8
333 in•lb [38 N•m]
M10
53 ft•lb [72 N•m]
M12
93 ft•lb [126 N•m]
0001675-M-EN: Rev C
Page of664
07-Oct-2022
The torque specifications listed above apply only to the track and
trailer assembly outlined in this manual. They do not apply to the
sawmill assembly. Follow the instructions in the sawmill operator’s
manual when assembling the carriage and sawhead.
BOLT TORQUE WARNING!

2018-2023 Woodlander™(MAX) Operator’s Manual
UNPACKING
Remove all the parts from the steel crate. Set the crate aside as it will be used as a support for
several of the assembly steps.
0001675-M-EN: Rev C
Page of764
07-Oct-2022

2018-2023 Woodlander™(MAX) Operator’s Manual
COMPONENT LISTS
Verify all component and hardware quantities are correct prior to assembling the trailer.
4x
End Gusset
[0001373]
4x
Jack Mount
[0001376]
6x
Joining Gusset
[0001374]
4x
Swivel Jack
[0006798]
2x
Long Side Plate
[0001363]
2x
Swivel Jack
Handle
[0006800]
4x
Short Side Plate
[0001364]
1x
Left Axle
Assembly
4x
Cross Beam
[STD: 0001369]
[MAX: 0002900]
1x
Right Axle
Assembly
1x
Front Cross
Beam
[STD: 0001370]
[MAX: 0002899]
6x
Axle Shim Plate
[0001682]
1x
Axle Cross
Beam
[STD: 0001679]
[MAX: 0002898]
2x
Wheel
[5.30-12]
1x
Left Axle Mount
[0001680]
1x
Tongue
[0001371]
1x
Right Axle
Mount
[0001681]
2x
Tongue Bracket
[0001372]
2x
Knob
M10 X 30 mm
[0001698]
1x
Hitch Ball
Coupler
(North America)
[0001381]
0001675-M-EN: Rev C
Page of864
07-Oct-2022