Woodland Mills Woodlander XL User manual

!
WOODLANDER™XL SAWMILL TRAILER
OPERATOR’S MANUAL
WDLRXL-MY2020: Rev A Publication Date: 27-Sep-2019
The Woodlander™ XL is compatible with HM126, HM130 & HM130MAX sawmills. Woodlander™is a trademark of Woodland Mills, Inc.

!
This page intentionally left blank.

Woodlander™XL Operator's Manual

TABLE OF CONTENTS
TABLE OF CONTENTS 1___________________________________
INTRODUCTION 3_________________________________________
GENERAL SAFETY RULES 4_______________________________
INSPECTION/MAINTENANCE 4______________________________
TECHNICAL SPECIFICATIONS 5____________________________
BOLT TORQUE SPECIFICATIONS 5_____________________________
TRAILER ASSEMBLY 6____________________________________
1. TOOLS REQUIRED 6______________________________________
2. UNPACKING 7____________________________________________
3. TRACK RAILS, JOINING GUSSETS, MIDDLE BUNK 8____________
4. LONG SIDE PLATES, JOINING GUSSETS 10___________________
5. TRACK RAILS, END BUNKS, END GUSSETS 12________________
6. JACK STANDS [TEMPORARY] 14____________________________
7. JOINING BUNKS, JOINING GUSSETS 15______________________
8. MIDDLE BUNKS, JOINING GUSSETS 17______________________
9. SHORT SIDE PLATES, CARRIAGE STOPS 19__________________
10. CROSS BEAMS, JACK MOUNTS [ENDS] 22____________________
11. CROSS BEAM, JACK MOUNTS [CENTRE] 25___________________
12. CROSS BEAMS, AXLE CROSS BEAM, AXLE MOUNTS 27________
13. AXLES 29________________________________________________
14. WHEELS 31______________________________________________
15. FENDERS 32_____________________________________________
16. TONGUE, HITCH COUPLER 34______________________________
17. LIGHTING 36_____________________________________________
18. BADGES 39______________________________________________
19. SAFETY CHAIN 41________________________________________
20. HEAD LOCK-DOWN PLATES 42_____________________________
WDLRXL-MY2020: Rev A
Page of 160
27-Sep-2019

Woodlander™XL Operator's Manual

NORTH AMERICAN PARTS LIST 45__________________________
EUROPEAN PARTS LIST 47________________________________
EXPLODED VIEWS 49_____________________________________
COMPLETE ASSEMBLY 49____________________________________
CHASSIS AND TRACK 50______________________________________
TONGUE 51_________________________________________________
NORTH AMERICA 51_____________________________________________
EUROPE 51______________________________________________________
AXLES, WHEELS, AND FENDERS 52____________________________
LIGHTING 53________________________________________________
NORTH AMERICA 53_____________________________________________
EUROPE 54______________________________________________________
BADGES 55_________________________________________________
HEAD LOCK-DOWN PLATES 56________________________________
NOTES 57_______________________________________________
WDLRXL-MY2020: Rev A
Page of 260
27-Sep-2019

Woodlander™XL Operator's Manual

INTRODUCTION
Congratulations on your purchase and welcome to Woodland Mills! This manual gives you the
necessary information about your Woodlander™XL sawmill trailer so you will be able to use it
properly. The entire manual must be read and understood before using the trailer. If any
questions should arise that are not covered by this manual, please contact Woodland Mills, Inc.
The Woodlander™sawmill trailer is compatible with HM126, HM130 & HM130MAX sawmill and
track systems for milling logs while the trailer is stationary and firmly supported on the ground.
It is not intended to carry any additional weight or be used as a utility trailer.
The Woodlander™ XL sawmill trailer is designed for certain applications only. We strongly
recommend the trailer not be modified and/or used for any application other than that for which
it was designed. If you have any questions relative to a particular application, DO NOT use the
trailer until you have first contacted Woodland Mills to determine if it can or should be performed
using the product.
For technical questions and replacement parts, please contact Woodland Mills, Inc.
OWNER'S RECORD
Please take a moment to record the following information about your
Woodlander™sawmill trailer. If you need to call for assistance, please be
ready to provide your model and serial numbers. This information will allow
us to help you more quickly when you call.
MODEL NUMBER
SERIAL NUMBER
DATE OF PURCHASE
WDLRXL-MY2020: Rev A
Page of 360
27-Sep-2019

Woodlander™XL Operator's Manual

**SAVE THESE INSTRUCTIONS**
GENERAL SAFETY RULES
!
!
INSPECTION/MAINTENANCE
•Check the tires before all trips. Make sure they are inflated to the pressure shown on the tire.
•Grease the axle bearings every 3 months or 1000 miles (1600 km), whichever comes first.
•Check the tow hitch ball coupler. Make sure it is not damaged.
•Check the wheel lug nuts before all trips. Make sure they are torqued properly.
•Check the lights. Make sure all the lights work properly. Replace any lights that do not work.
•Inspect trailer before all trips for any damaged or loose parts.
WARNING!
Read and understand all instructions. Failure to follow all instructions
listed below may result serious injury.
WARNING!
The warnings, cautions, and instructions discussed in this instruction
manual cannot cover all possible conditions or situations that could
occur. It must be understood by the operator that common sense and
caution are factors which cannot be built into this product but must be
supplied by the operator.
WDLRXL-MY2020: Rev A
Page of 460
27-Sep-2019

Woodlander™XL Operator's Manual

TECHNICAL SPECIFICATIONS
BOLT TORQUE SPECIFICATIONS
Item
Specification
Trailer Axle
Independent Torsion Axle Design
Trailer Wheels
5 Bolts @ 4.5” (114 mm) & 5.30-12 DOT Approved Tires
Tire Pressure
Refer to Tire
Wheel Nut Torque
80 ft•lb / 110 N•m
Trailer Ball Coupler
2” / 50 mm
Trailer Lights
LED Light Kit (stop, turn, tail, side markers, and license plate light)
Finish
Powder Coat Paint / Galvanized Steel
Fenders
Removable
Safety
Locking pins and safety straps to secure sawhead while travelling
Bolt (Thread Size)
Torque
M5
78 in•lb / 9 N•m
M6
133 in•lb / 15 N•m
M8
333 in•lb / 38 N•m
M10
53 ft•lb / 72 N•m
M12
93 ft•lb / 126 N•m
WDLRXL-MY2020: Rev A
Page of 560
27-Sep-2019

Woodlander™XL Operator's Manual

TRAILER ASSEMBLY
1. TOOLS REQUIRED
Tool
Specification
Phillips Head Screwdriver
No. 3
Wrench/Socket
8 mm
Wrench/Socket
9 mm
Wrench/Socket
10 mm
Wrench/Socket
13 mm
Wrench/Socket
14 mm
Wrench/Socket
15 mm
Wrench/Socket
18 mm
Adjustable Wrench
Variable
Torque Wrench
Capable of 93 ft•lb (126 N•m)
Drill
Corded or cordless
WDLRXL-MY2020: Rev A
Page of 660
27-Sep-2019

Woodlander™XL Operator's Manual

2. UNPACKING
Remove all the parts from the steel crate. Set the crate aside as it will be used as a support for
several of the following steps.
WDLRXL-MY2020: Rev A
Page of 760
27-Sep-2019

Woodlander™XL Operator's Manual

3. TRACK RAILS, JOINING GUSSETS, MIDDLE BUNK
Using the hardware listed below, assemble the gussets to the track as shown on the next page.
Torque all bolts per the table in section BOLT TORQUE SPECIFICATIONS.
Track components listed in these tables are not included with the trailer package, namely track
rails, joining plates, bunks, and carriage stops. These components are found in the sawmill
crate. If the trailer was purchased for an existing sawmill (i.e. the sawmill is currently
assembled), the track will need to be disassembled prior to building the trailer.
When assembling the track, ensure the gussets are flush with the track rails as shown in the
graphic below. Measure diagonally to check for squareness.
12x
M10 X 30 mm
Flanged Hex
Bolt
1x
Middle Bunk
12x
M10 Flanged
Lock Nut
4x
Joining Plate
2x
Track Rail
2x
Joining Gusset






WDLRXL-MY2020: Rev A
Page of 860
27-Sep-2019
Use the fasteners included with the
sawmill trailer to assemble the
track. The fasteners included with
the sawmill track will not be used.
HM126/HM130 = 30-½in [775 mm] Track Width
HM130MAX = 37 in [940 mm] Track Width
Flush
Flush