World Market TYLER BI-CAST 575119 User manual

**FULLY ASSEMBLED ITEMS NEED ONLY COVER SHEET AND CARE INSTRUCTIONS**
Standard Letter Size 8.5” x 11” paper.
Assembly Instructions
TYLER BI-CAST OFFICE CHAIR
SKU 575119 / 542938
NOT FOR COMMERCIAL USE.
THANK YOU FOR YOUR PURCHASE. IF YOU HAVE ANY QUESTIONS
PERTAINING TO THE ASSEMBLY OF THIS FURNITURE PIECE, PLEASE CONTACT
THE NEAREST COST PLUS WORLD MARKET STORE.
IF YOU ARE NOT NEAR A STORE, PLEASE CALL OUR CUSTOMER SERVICE CALL
CENTER TOLL FREE AT 877- 967-5362 FOR ASSISTANCE.
Page 102/28/2019

Component List
LABEL DESCRIPTION QTY
A Seat 1
B Lift Mechanism 1
C Gas Lift 1
D Base 1
E Caster 4
Hardware List
LABEL DESCRIPTION QTY
H-1 Large Allen Bolt
6x35mm 2
H-2 Small Allen Bolt
6x25mm 2
H-3 Spring Washer
6mm 4
H-4 Flat Washer
6mm 4
Tool List
LABEL DESCRIPTION QTY
T-1 Allen Key 1
Page 202/28/2019

Assembly Preparation
Before Beginning:
Have 2 adults on hand for assembly-
Save all packaging until finished-
Assemble on a clean non-marring surface (packing foam)-
Do not assemble on flooring or carpet-
In case of missing parts, please contact your nearest Cost Plus World
Market store or call our customer service call center at call 1-877-967-5362.
Read instructions, cover to cover-
Unpack all hardware bags and components to ensure you have all parts-
Page 302/28/2019

Assembly Steps
Step 1
Insert Caster (E) to Base (D) as shown.
D
E
E
E
E
Step 2
Remove and discard plastic cap from Gas Lift (C). Insert Gas Lift (C) into the center hole of Base (D) as shown.
DC
C
Remove and discard
Remove and discard
sticker
Page 402/28/2019

Assembly Steps
Step 3
Carefully turn over Seat (A) so that the bottom is flat and faces upward as shown. Remove the protective sheet before
attaching Lift Mechanism (B).
Step 4
Align front holes on Lift Mechanism (B) to pre-threaded front holes on Seat (A). Attach the front of Lift Mechanism (B)
using Large Allen Bolts (H-1), Spring Washers (H-3) and Flat Washers (H-4), stacking hardware in the order as shown.
Engage Large Allen Bolts (H-1) using Allen Key (T-1) but do not fully tighten them until Step 5.
A
A
B
H-1
H-3
H-4
B
A
Front
Page 502/28/2019

Assembly Steps
Step 5
Align back holes on Lift Mechanism (B) to pre-threaded front holes on Seat (A). Attach the back of Lift Mechanism (B)
using Small Allen Bolts (H-2), Spring Washers (H-3) and Flat Washers (H-4), stacking hardware in the order as shown.
Fully tighten ALL Allen Bolts from Steps 4 and 5 using Allen Key (T-1).
Step 6
Position the Seat (A) facing down over the top of Gas Lift (C). Insert the Gas Lift (C) into the center hole of
Lift Mechanism (B) and press down until fully engaged. The chair is now ready for use.
B
A
A
C
A
B
H-2
H-3
H-4
Page 602/28/2019

Operating Instructions
Function Instruction # 1
To Adjust Seat Height:
While seated, lean forward and reach under the right side of the chair to find the handle. Lift the handle and raise your
body up slightly to allow the chair to rise to the desired height. Once desired height is reached, release handle to lock
chair at desired height. To lower the seat, lift the handle while seated. The chair will descend until the handle is
released or the chair reaches the bottom position.
Page 702/28/2019

Operating Instructions
Function Instruction # 2
To Operate Tilt Lockout:
While seated, reach under the right side of the chair to find the height-adjustment handle. Pull the handle all the way
out (away from the gas lift) to allow the chair to tilt backwards. To lock the chair in the upright or vertical position, sit
upright and push the handle in towards the gas lift.
Page 802/28/2019

Operating Instructions
Function Instruction # 3
To Adjust Chair Reclining Tension:
From the seated position, reach under the front center of the chair, grasp the Tension Knob and turn it
counter-clockwise to tighten the tilt mechanism for added tension. Turn the Tension Knob clockwise to loosen the
tilt mechanism for less tension.
NOTE: Over-loosening the Tension Knob can cause unexpected chair recline when seated. Be aware of tension
status before sitting.
Tension Knob
Page 902/28/2019

Operating Instructions
Function Instruction # 4
360-degree Swivel:
The chair swivels freely clockwise or counter-clockwise.
Page 1002/28/2019