World Market Andorra 629622 User manual

Assembly Instructions
Thank you for your purchase. If you have any questions pertaining to the assembly of this
furniture piece, please contact the nearest World Market store. If you are not near a store,
please call our customer service call center toll free at 877-967-5362 for assistance.
ALL PRODUCTS SOLD AT WORLD MARKET ARE NOT
FOR COMMERCIAL USE AND ARE INTENDED FOR
RESIDENTIAL USE ONLY.
SKU 629622/629667
Cover page - for furniture goods that require customer level assembly. A/I are cover page, components and
hardware lists, assembly steps, anti-tip kit info (if applicable), care & maintenance and warranty info.
2023. 09.11
PAGE 1
V
Andorra Corner

1
Left Back Cushion
F1
Seat Cushion
A
B
C
E
Seat Frame
Backrest Frame
Leg
1
H-1
H-2
Spring Washer M8
4
4
4
2
4
H-3
D1
4
Allen Bolt (M8x80)mm 4
H-4
H-5
Hexagonal Nut M8
Flat Washer (M8x1.2)mm
Plastic Flat Washer
Component List
Hardware List
Allen Key
1
T-2
1
T-1
Tool List
2023. 09.11
PAGE 2
V
Right Back Cushion
GStrap Connector 2
Wrench 13

Read the assembly instructions, cover-to-cover. Save any Care and Maintenance instructions pages for
after the assembly has been completed.
In case of missing parts, please contact your nearest World Market store or call our customer service call
center at 1-877-967-5362.
Assemble on a clean non-marring surface (such as the product’s packing foam).
Unpack all hardware bags and components to ensure you have all parts. Take note of bolt hardware
size differences and components that may have directional labels (Example: TOP or FRONT).
It is always recommended to have 2 adults on hand for assembly.
Do not assemble on hard, abrasive flooring or carpeted surfaces that can damage or get caught in the
components during assembly.
Do not discard any packaging until the product has been fully assembled.
WARNING: Small parts are a choking hazard. Adult supervision is required before, during, and after
assembly.
Assembly Preparation
Before Beginning:
2023. 09.11
PAGE 3
V

Assembly Steps
Step 1
(H-5) Plastic Flat Washer x 4
2023. 09.11
PAGE 4
V
Using a second person to assist you, place Seat Frame (A) upside down onto a padded, non-marring surface.
Position the corner Legs (C) on Seat Frame (A) as shown.
Position the Plastic Flat Washers (H-5) between the legs and the seat frame and tighten by turning clockwise. DO NOT OVER
TIGHTEN.
H-5
A
C
C
C
x4
C
Clockwise
Step 2
x4
(H-1) Allen Bolt x 4
(H-2) Flat Washer x 4
(H-3) Spring Washer x 4
(H-4) Hexagonal Nut x 4
(T-1) Allen Key
(T-2) Wrench 13
H-1
H-2
H-3
H-4
T-1
T-2
Clockwise
Using a second person to assist you, place the assembly upright. Position the Backrest Frame (B) onto either side of the Seat
Frame (A). Secure the Backrest Frame (B) by inserting Allen Bolts (H-1) through the top of the holes, ensuring it protrudes out
the bottom, and thread the Spring Washers (H-3), Flat Washers (H-2) and Hexagonal Nuts (H-4), stacking the hardware in the
order as shown. Engage all hardware first, then fully tighten using the provided Allen Key (T-1) and Wrench (T-2). DO NOT
OVER TIGTHEN.
B
B

Assembly Steps
2023. 09.11
PAGE 5
V
Step 3
x6
Velcro
Position Seat Cushion (F) into position as shown, ensuring the zipper faces down. Secure using the preattached Velcro straps to the
bottom rail of the Backrest Frame (B). Position the Back Cushions (E), (D) into position as shown, ensuring the zipper faces down and
the angles surface faces to the front. Secure using the preattached Velcro straps to the mid rail of the Backrest Frame (B).
Step 4
ADJUSTABLE LEVELER
Levelers are located on the bottom of each leg and
may be used for additional adjustment if needed
for uneven surfaces.
Assembly is now complete and the product is ready for use. Adjustable levelers are located on the bottom of each leg and may be
adjusted by turning outwards, counter-clockwise to help account for uneven surfaces. NOTE: Hardware may loosen over time.
Periodically check that all connections remain tight and adjust as needed.
D
F
E
ED

Assembly Steps
Step 5
1
2
G
x2
If joining with with a partnering piece, place both assemblies side by side in your desired orientation. Secure together by threading
two provided Strap Connectors (G) through the webbing and around each frame, one toward the front of the frames and one
toward the back. Tightly secure.
PAGE 6
2023. 09.11

2023. 09.11
PAGE 7
V

2023. 09.11
PAGE 8
V