Worx MAKERX WX747.X User manual

20V Cordless Mini Blower WX747
WX747.X

1
3
4
5678
2

A3 A4
B C
ED
A2A1

A3 A4
BC
ED
A2A1

5
EN
ORIGINAL INSTRUCTION
PRODUCT SAFETY
GENERAL POWER TOOL SAFETY
WARNINGS
WARNING Read all safety
warnings and instructions.
Failure to follow the warnings and
instructions may result in electric
shock, fire and/or serious injury.
Save all warnings and instruc-
tions for future reference.
The appliance is only to be used
with the power supply unit pro-
vided with the appliance.
IMPORTANT
READ CAREFULLY BEFORE
USE.
KEEP FOR FUTURE
REFERENCE.
Safe operating practices
1) Training
a) Read the instructions
carefully. Be familiar with
the controls and the correct
use of the machine.
b) Never allow children,
persons with reduced
physical, sensory or mental
capabilities or lack of
experience and knowledge
or people unfamiliar with
these instructions to
use the machine, local

6
EN
regulations may restrict the
age of the operator.
c) Never operate the machine
while people, especially
children, or pets are nearby.
d) Keep in mind that the
operator or user is
responsible for accidents or
hazards occurring to other
people or their property.
2)Preparation
a) While operating the
machine, always wear
substantial footwear and
long trousers. Do not
operate the machine when
barefoot or wearing open
sandals. Avoid wearing
clothing that is loose fitting
or that has hanging cords or
ties.
b) Do not wear loose clothing
or jewellery that can be
drawn into the air inlet. Keep
long hair away from the air
inlets.
c) Obtain ear protection and
safety glasses. Wear them at
all times while operating the
machine.
d) Operate the machine in a
recommended position and
only on a firm, level surface.
e) Do not operate the machine
on a paved or gravel surface

7
EN
where ejected material
could cause injury.
f) Before using, always visually
inspect to see, that the
fasteners are secure, the
housing is undamaged and
that guards and screens
are in place. Replace worn
or damaged components
in sets to preserve balance.
Replace damaged or
unreadable labels.
3)Operation
a) Before starting the machine,
make certain that the
feeding chamber is empty.
b) Keep your face and body
away from the feed intake
opening.
c) Do not allow hands or any
other part of the body or
clothing inside the feeding
chamber, discharge chute,
or near any moving part.
d) Keep proper balance and
footing at all times. Do not
overreach.
e) Always stand clear of the
discharge zone when
operating this machine.
f) If the machine should start
making any unusual noise or
vibration, immediately shut
off the power source and
allow the machine to stop.

8
EN
Remove the battery pack
from the machine and take
the following steps before
restarting and operating the
machine:
i) inspect for damage;
ii) replace or repair any
damaged parts;
iii) check for and tighten any
loose parts.
g) Do not allow processed
material to build up in the
discharge zone; this may
prevent proper discharge
and can result in kickback of
material through the intake
opening.
h) If the machine becomes
clogged, shut-off the
power source and remove
the battery pack from the
machine before cleaning
debris.
i) Never operate the machine
with defective guards or
shields, or without safety
devices.
j) Keep the power source
clean of debris and other
accumulations to prevent
damage to the power
source or possible fire.
k) Do not transport this
machine while the power
source is running.
l) Always disconnect the

9
EN
machine from the power
supply (e.g. remove the
battery pack from the
machine)
- whenever you leave the
machine,
- before clearing blockages
or unclogging chute,
- before checking, cleaning
or working on the machine.
m) Avoid using the machine
in bad weather conditions
especially when there is a
risk of lightning.
4)Maintenance and storage
a) keep all nuts, bolts and
screws tight to be sure the
appliance is in safe working
condition.
b) Replace worn or damaged
parts.
c) Use only genuine
replacement parts and
accessories.
d) Store the machine in a dry
place out of the reach of
children.
e) When the machine is
stopped for servicing,
inspection, or storage, or
to change an accessory,
shut off the power source,
disconnect the machine
from the supply and make
sure that all moving parts

10
EN
are come to a complete
stop. Allow the machine
to cool before making any
inspections, adjustments,
etc. Maintain the machine
with care and keep it clean.
f) Store the machine in a dry
place out of the reach of
children.
g) Always allow the machine to
cool before storing.
h) Never attempt to override
the interlocked feature of
the guard.
SAFETY WARNINGS FOR BAT
TERY PACK
a)Do not dismantle, open
or shred cells or battery
pack.
b)Do not short-circuit a
battery pack. Do not
store battery packs
haphazardly in a box or
drawer where they may
short-circuit each other
or be short-circuited by
conductive materials.
When battery pack is not
in use, keep it away from
other metal objects, like
paper clips, coins, keys,
nails, screws or other small