Xenarc 1200TS Installation and operating instructions

U
Us se er r M Ma an nu ua al l / / I In ns st ta al ll la at ti io on n G Gu ui id de e
1
12 2" " L LC CD D T To ou uc ch h M Mo on ni it to or r
Warning! The monitor may malfunction if it is operated with a different power supply or if it
is supplied with the incorrect power voltage. Do not expose this unit to rain or moisture as this
may result in fire or electric shock.
Content:
I. FCC Warning Statement............................................................................... 1
II. Introduction................................................................................................... 2
Features.................................................................................................................................2
Unpacking the monitor..........................................................................................................2
III. Installation..................................................................................................... 4
I/O placement........................................................................................................................4
To PC ....................................................................................................................................4
Touch Driver installation.......................................................................................................5
MSR installation (optional) ...................................................................................................8
Control Buttons...................................................................................................................10
Structure of OSD settings....................................................................................................11
IV. For your safety............................................................................................12
V. Support timing chart ..................................................................................12
VI. Mechanical Dimension:.............................................................................. 12
VII. Product General Specification..................................................................13

Version. 1.0
1
I. FCC Warning Statement
WARNING
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help.
Notice:
(1) An Unshielded-type power cord is required in order to meet FCC emission limits and also to
prevent interference to nearby radio and television reception. It is essential that only the
supplied power cord is used.
(2) Use only shielded cables to connect I/O devices to this equipment.
(3) Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.

Version. 1.0
2
II. Introduction
The 1200TS is a 12” TFT LCD monitor integrated with a resistive touch panel. Please
contact us for optional MSR and optional 2nd display.
Features
-Optimal display resolution 1024 * 768
-VESA75 * 75 mm wall mount standard
-Durable and sturdy base design
-Optional 3 track Magnetic Strip Reader (MSR)
-Optional 2nd display (7”/8.4”)
-Adjustable viewing angle up to 90 degrees horizontally
-Low power consumption of only 20W with LED backlight
Unpacking the monitor
-Place the monitor on a clean surface, making sure the box is in an upright position.

Version. 1.0
3
Check accessory
Please make sure all of the following accessories are included:
Standard Items
a. b.
c. d. e.
Optional Items
a. b.
a. MSR b. 2
nd
display ( 7” or 8.4” )
a. LCD Monitor
b. VGAcable
c. Touch cable (USB or RS232)
d. Power adaptor
e. Power cable

Version. 1.0
4
III. Installation
I/O placement
1 DC JACK
2 DVI
3 VGA
4 USB B Type
5 Dual USBAType
6RS232
7 RJ45(RS232)
To PC
1. Connect VGAcable from monitor to PC
2. Connect USB touch cable to PC
3. Connect DC plug to monitor and the other side to wall outlet

Version. 1.0
5
Touch Driver installation
1. Double click “setup.exe” from driver menu 2. Click “next” from welcome window
3. Click “next” from License Agreement 4. Click “next” from Setup Type
5. Click “next” 6. Click “next” from Setup Type

Version. 1.0
6
7. Click “next” from Setup Type 8. Click “next” from Choose Destination Location
9. Click “next” from Select Program Folder 10. Click “next” from Setup Type
11. Click “next” from Setup Type 12. Click “next” from Setup Status

Version. 1.0
7
Calibration procedures:
1. Double click the “eGalax Touch” icon to run calibration function
2. Follow 4 point linearity calibration procedures and save the data
3. Follow free draw calibration
4. Exit calibration menu

Version. 1.0
8
MSR installation (optional)
Components of MSR Kit:
1. Slide the MSR into position on the display.
2. Fasten the screws (x2).
Second Display installation (optional)：
To install the Second Display, please open the VFD cover first.
Components of Second Display Kit with power adapter:
1. Fix the parts of Second Display modules as steps ❶❷❸as above left
picture shows. (detailed steps as below)
❶Put the second display upside down.
❷Place the metal bracket onto the rear side of the second display
and fasten the screws (x4) to fix metal bracket with the system.

Version. 1.0
9
❸Align the plastic bracket into position on the metal bracket.
(a) Align the plastic bracket onto the metal bracket.
(b) Push left until the click sound is heard.
2. Fasten the screw (x1) to fix the plastic bracket and Second Display module
with metal bracket.
3. Slide the Second Display Module into the slot.
4. Fasten the screws (x2) to fix the Second Display module with the System.
5. Connect the VGAcable to the Second Display Module and the System.
6. Connect the DC plug to the Second Display Module and the other side to
power source.

Version. 1.0
10
Control Buttons
Power Use the power switch to turn the power ON or OFF. We recommend turning
your system power on first, then the LCD monitor.
Auto Adjusting
a.) Press to execute AUTO-
Adjust function. This function will set the monitor
display area to the optimal position.
b.) Sometimes this function can't achieve the optimal effects. Please follow
the manual adjustment procedure.
Up a.) When OSD mode is activated (When “MENU” key is pressed). The two
keys are used to select the adjustment items.
b.) When adjustment item is selected, the two keys are us
ed to decrease or
increase the value of each selected item.
Down
Menu
When the light bar moves other items
, the key are used to select it, and read
to adjust. Press the MENU key to activate the On Screen Display (OSD).
Press twice to turn off the OSD. After 30 sec idle time, the OSD screen will
automatically turn off.

Version. 1.0
11
Structure of OSD settings
Main
Menu
First Level Second Level
Third
Level
Operating Procedure
Auto Adjust
Press “UP” or “DOWN” to adjust H-phase &
H-position & V-position clock automatically.
Luminance Brightness Contrast
Exit
Press “UP” key to increase brightness, “DOWN”
key to decrease brightness.
Press “UP” key to increase contrast, “DOWN” key
to decrease contrast.
Geometry
H. Position
V. Position
Clock
Phase
Exit
Press “UP” key to shift screen right, “DOWN” key
to shift screen left.
Press “UP” key to shift picture upward, “DOWN”
key to shift picture downward.
Adjust sampling clock of analog to digital
converter until clock is equal to pixel frequency of
video input.
By varying this “UP” “DOWN” control the exact
sampling time within the pixel can be adjusted.
Color
9300K
6500K
5800K
Press “UP” or “DOWN” to choose three types of
color temperature 9300°k, 6500°k and user
defined.
User Preset
Red
Green
Blue
Exit
Exit
OSD
H. Position
V. Position
OSD Timeout
Exit
Adjust OSD frame horizontal location, press “UP”
key to shift frame right, “DOWN” key to shift frame
left , timeout and preset OSD.
Adjust OSD frame vertical location, press “UP”
key to shift frame upward, “DOWN” key to shift
frame downward , timeout and preset OSD.
Language
English
French
German
Italian
Spanish
Japanese
T. Chinese
S. Chinese
Press “UP” or “DOWN” to choose any one of the
following languages: English, French, German,
Italian, Spainish , Japanese, Traditional Chinese
or Simplified Chinese.
Recall
Color Recall
Recall All
Exit Recall the default value.
Miscellaneous
Sharpness
Display
Information
Exit
Press “UP” key to increase sharpness, “DOWN”
key to decrease sharpness.
Exit

Version. 1.0
12
IV. For your safety
1. When moving the monitor, always switch off power and disconnect all cables to avoid
any danger.
2. Please use the power and signal cables correctly when installing or adjusting it.
3. In case of notice any abnormal smell or noise, please stop operation and call the nearest
dealer or service center.
V. Support timing chart
Timing
Mode
Reference
Standard Resolution
Pixel
MHz FH KHz
FV Hz Interlace
H
Polarity
V
Polarity
Mode 1
VESA
1024×768
65.000
48.363
60.004
NO
-
-
Mode 2 VESA 1024×768 75.000 56.476 70.069 NO - -
Mode 3 VESA 1024×768 75.011 57.524 72.000 NO + +
Mode 4 VESA 1024×768 78.750 60.023 75.029 NO + +
VI. Mechanical Dimension:

Version. 1.0
13
VII. Product General Specification
Model 12” LCD Touch Monitor
COLOR BLACK
Display size 12”
Display Area 245.76 * 184.32 mm
Optimal Resolution 1024 * 768
Brightness (Panel) 500 cd/m2 (typ)
Contrast Ratio 700:1 (typ)
Response Time 16ms (typ)
Viewing Angle(L/R/U/D) 80 / 80 / 70 / 70 (typ)
Input Video signal connector D-Sub 15 pins + DVI-D
Power consumption 20W
Input Frequency H: 31.5-60.2 kHz ; V: 56.3-75Hz
Power supply DC 12V +/- 10%
Temperature Operating : 0℃~40℃; Storage : -10℃~50℃
Weight (Net) 3.48kgs
Physical Dimension 315 (W) * 319 (H) * 200 (D) mm
Approvals CE, FCC
Touch Technology 5W Resistive touch
Wall Mount type VESA 75 * 75 mm
Optional items
Wall Mount Bracket
MSR 3 Tracks
2nd Display 7”/8.4”
Customer Display VFD