xpr MTPADP-BT-EH-SA User manual

USER’S MANUAL
MTPADP-BT-EH-SA
Bluetooth® standalone keypad with integrated RFID reader
1. SPECIFICATIONS
User capacity:
Relays:
Output:
Entry mode:
RFID reading type:
Reading distance:
PIN Code Length:
Power supply:
Buzzer, backlight control:
Tamper:
RS-485 interface:
Door Open Time:
IP Factor:
Operating Temperature:
Operating Humidity:
Firmware upgrade:
Wiegand output:
Programming:
Door operation:
Holidays:
Event capacity:
100 Cards and 100 PIN Codes
1 or 2 depending on the remote relay unit
1 with RTT and RU1 and 2 with RU2 and DINRTT
RS-485, Wiegand
PIN Code, Card, PIN Code or Card
EM 4002/4100 and HID (125kHz)
up to 4cm
6 Digits
12 VDC; max. 100mA
Yes, ON/OFF via XPR Smart Admin
Yes
Yes, for connecting I/O boards like
RU1, RTT, RU2, DINRTT
0 to 255 sec. or toggle (ON/OFF mode)
IP65
20ºC to +50ºC
5% to 95% RH without condensation
Yes, via Bluetooth® wireless technology
Wiegand 24, 26, 32, 34, 56, 58 bits
or 4, 6, 8 bit per key for the keypad
via XPR Smart Admin
via XPR Smart Access
24
4000
1
2. MOUNTING
Cable
Ø6.0
30mm
+12V
gnd
d0
d1
xx
xx
xx
xx
92mm
27mm
51mm
3 (3 x 30mm)
5mm
1 (M3 x 6mm)
v.b8
EN
Access Granted
(Output 1 or 2)
Idle Mode Access Denied
Tricolor indication LED
3. RESET READER TO DEFAULT
1. Turn the device OFF
2. Put dipswitch 1 to position ON
3. Turn the power ON
4. Wait approx. 15 seconds until continuous beeps.
5. Put dipswitch 1 to OFF
6. Wait for long beep and orange back light led.
The reset procedure will bring the reader to default.
The password will be deleted, all the users and the
reader will be unpaired from the remote relay unit.
Unpairing the reader after reset, prevents
unauthorized reset and keeps the unit in high
security state.
Important note:
The Bluetooth reader comes with RU1 remote relay ®
unit.
Make sure to make firmware update with the latest
available firmware.
ON
1 2
Reset
Service mode

2
IN
RS-485 (max. 50m)
DINRTT
2 Relay Remote Unit
and request-to-exit Button
MTPADP-BT-EH-SA
Bluetooth standalone keypad with
integrated RFID reader
RTT
1 Relay Remote Unit
and request-to-exit Button
RU2
2 Relay Remote Unit
OR
Secured Area Unsecured Area
+12V
GND
NO
COM A
B
NC
PB
RS 485
Power
Supply
GND_P B
RU1
1 Relay Remote Unit
Grey
Red
Black
White
Yellow
Pink
Blue
Violet
+12V
GND
D0
D1
RS-485
Power Supply
Wiegand
Tamper
A
B
to remote relay unit
to wiegand controller
4. WIRING AND PAIRING
Pairing the reader with remote relay unit is done
from the remote relay unit and enables added
security. After being paired, it is not possible to
switch any of the devices, since the reader will work
only with the paired remote relay unit.
The Bluetooth reader must be connected to remote
relay unit, unless is used as wiegand reader.
The remote relay units compatible with MTPADB-BT-
EH-SA are RU1, RU2, RTT and DINRTT. Once
connected, the remote relay unit must be paired
with the Bluetooth reader.
There are four options to wire and pair the reader. It can be paired to RU2, RU1, DINRTT and RTT.
4.1 Wiring and pairing MTPADP-BT-EH + RU1
+12V
GND
NO
COM A
B
NC
PB
RS-485
Power
Supply
GND_PB
white
yellow
gray
red
black
blue
orange
violet
pink
Black
Red
Pink
Violet
Reader
Exit Button
Electric
Door Strike
12 VDC +
-
+
-
max. 50 m
Pairing Reader with RU1 (high security)
- Keep the button pressed
for at least 5 sec. and the
units will be paired.
Other pairing devices:
Device Description Relays
RU2
DINRTT
RTT
Flush mount sensitive push button and remote relay
DIN rail mount remote relay unit
Surface mount sensitive push button and remote relay
2
2
1
4.2 Wiring MTPADP-BT-EH-SA to wiegand controller
Grey
Red
Black
White
Yellow
Pink
Blue
Violet
12V
DC(CC)
D0
D1
+
-
Host/ Unité Centrale/ Unita' centrale/
Sistema receptor/ Controller/ Controller
Max 150m
By default, the reader is set to Wiegand 26
bit for both the keypad and the RFID reader.
You can set the reader, using the software,
to Wiegand 24, 26, 32, 34, 56, 58 bits.
You can set the keypad to send 4, 6 or 8
bits per key, while the RFID reader (card)
sends wiegand.

3
5. SETTING UP READERS WITH XPR SMART ADMIN WINDOWS SOFTWARE
1. Add site first.
2. Click on “ADD” reader.
3. Select type “MTPADP-BT-EH-SA”.
4. Scan for readers near by by clicking on “Scan”. Found
readers will be listed (pic.2). Click on “Select”.
5. Add a pairing key between the PC and the Bluetooth reader
and a password. (pic. 3)
6. If the pairing is successful, the buttons in the reader
section will be enabled. (pic.4)
pic. 1
pic. 2
pic. 3
pic. 4
6. ADDING USERS
1. Go to Users and select the user. Edit the name
directly. Enable it.
2. Put a PIN Code and Card ID. The Card ID can be
read directly from the reader or from USB desktop
reader.
3. Select proper Access level and validity period.
4. After this, go to the reader and “Upload users to
reader”.
You can download 2 softwares for Windows: XPR Smart Access and XPR Smart Admin from our website:
The 2 smartphone apps are available in:
Smart
Access
Users App
Application for users, allowing them
to manage the doors from a
distance.
(max distance: 10m).
Smart
Admin
Administrator App
Application for the installation administrator,
allowing him/her to program one reader at a
time and update it, manage users and their
access rights, download events and edit
reports.
Users Software
Application for users,
allowing them to manage
the doors from a distance.
(max distance: 10m).
Software for the installation
administrator, allowing him/her to
program all readers and update
them, manage users and their
access rights, download events
and edit reports.
Administrator Software
This product herewith complies with requirements of EMC directive 2014/30/EU, Radio Equipment Directive 2014/53/EU. In addition it complies with RoHS2 directive EN50581:2012 and RoHS3 Directive
2015/863/EU.
Web page
wwww.xprgroup.com