Yaesu FTM-300DE Reference guide

1. Turn the transceiver ON.
2. Press the [BAND(SQL)] key to enter the 144 MHz band.
3. Press and hold the [MHz(SETUP)] key.
4. Rotate the DIAL knob to select “OPEN MSG 28” and
then press the [MHz(SETUP)] key.
5. Rotate the DIAL knob to select “MESSAGE” and then
press the [V/M(MW)] key.
6. Enter “AH075M”.
1) Rotate the DIAL knob to select “A”, then press the [V/
M(MW)] key.
2) Repeat the previous step to complete the MESSAGE
“AH075M”.
3) Press and hold the [MHz(SETUP)] key.
Information for Customers Operating VHF/UHF Transceivers in the UK
Thank you very much for purchasing the YAESU transceiver.
The transceivers listed in this notice are congured at the factory with the ARS (Automatic Repeater Shift) Frequency
Range, and the Repeater shifts, as shown in the below chart “”.
When any of the listed transceivers is operated in a location where the frequency range and repeater shifts in use are
as shown in the chart “”; follow the respective procedure to change the Automatic Repeater
Shift conguration, before using the transceiver for the rst time.

Factory Default Setting

Selectable Setting
ARS Frequency Range: 438.20 MHz - less than 439.45 MHz (- shift)
Repeater Shifts: 7.6 MHz
ARS Frequency Range: 433.00 MHz - less than 433.40 MHz (+ shift)
434.60 MHz - less than 435.00 MHz (- shift)
Repeater Shifts: 1.6 MHz
Caution:
• BychangingtheARSdesignatedbandsandrepeatershiftsaccordingtotheproceduresbelow,allsaveddata,suchas
MenuandMemorysettings,willbedeleted.IfyouneedtochangetheARSfeaturesettingafterusingtheradio,make
suretobackupyourregistereddataormakeawrittennote,beforeapplyingthesettingchange.
• TheARSfeaturesettingisNOTchanged,evenwhenexecutingthe“FactoryReset”torestorethetransceivertothe
factorydefaults,asdescribedintheOperatingManuals.
7. Turn the transceiver OFF.
8. Press and hold the [BAND(SQL)], [GM(AMS)] and
[MODE(DG-ID)] keys while turning the transceiver ON.
9. <TYPE B2> appears in the display.
10.Rotate the DIAL knob to select <TYPE C2> and press
the [GM(AMS)] key. The transceiver will re-start auto-
matically. Setting of the
ARS feature to “Cong-
uration C2” is success-
fully completed.
TorestoretheARSfeaturesettingtothefactorydefault(B2),
performthesameproceduresabove.


1. Turn the transceiver OFF.
2. Connect the supplied microphone SSM-85D to the trans-
ceiver.
3. Press and hold the [F(SETUP)] and [GM] keys while turn-
ing the transceiver ON.
4. Press the [Power] key briey, then “LOCK” will appear on
the display for one sec.
5. Press
[8]à[9]à[7]à[7]à[3]à[]keys on the SSM-
85D microphone.
6. <TYPE B2> appears in the display.
7. Press the [Power] key briefly, then “UN LOCK” will ap-
pear on the display for one sec.
8. Rotate the DIAL knob to se-
lect <TYPE C2> and press
and hold the DIAL knob. The
radio will re-start automatical-
ly. Setting of the ARS feature
to “Configuration C2” is suc-
cessfully completed.
TorestoretheARSfeaturesettingtothefactorydefault(B2),
performthesameproceduresabove.

1. Turn the transceiver OFF.
2. Connect the supplied microphone MH-48A6JA to the
transceiver.
3. Press and hold the [F(MW)] and [GM] keys while turning
the transceiver ON.
4. Press the [Power] key briey, then “LOCK” will appear on
the display for one sec.
5. Press
[8]à[3]à[7]à[8]à[3]à[7]keys on the MH-
48A6JA microphone.
6. Press the [Power] key briey, then “UNLOCK” will appear
on the display for one sec.
7. Press and hold the [DISP(SETUP)] key.
8. Touch the [RESET/CLONE]on the display.
9. The ARS Configuration
name “B2” will appear in the
top right of the display.
10.Press [F(MW)] key, then the
message <Confirming FROM
“B2” TO “C2”> will appear on
the display.
BACK
BACK
RESET/CLONE




FACTORY RESET
PRESET
RECALL PRESET
MEM CH RESET
〉
〉
〉
〉
VERSION
MAIN :x.xxx 0EXP B2
PANEL:x.xx
11. Touch [OK?]. The radio will re-start automatically. Set-
ting of the ARS feature to “Conguration C2” is success-
fully completed.
TorestoretheARSfeaturesettingtothefactorydefault(B2),
performthesameproceduresabove.


1. Turn the transceiver OFF.
2. Connect the supplied microphone MH-48A6JA to the
transceiver.
3. Press and hold the [A/B(DW)] and [GM] keys while turn-
ing the transceiver ON.
4. Press the [Power] key briey, then “LOCK” will appear on
the display for one sec.
5. Press
[8]à[3]à[7]à[8]à[3]à[7]keys on the MH-
48A6JA microphone.
6. Press the [Power] key briey, then “UNLOCK” will appear
on the display for one sec.
7. Press and hold the [DISP(SETUP)] key.
8. Rotate the DIAL to select [13 RST/CLONE], then press
the [DISP(SETUP)] key.
9. Rotate the DIAL to select [8 SOFTWARE VERSION],
then press the [DISP(SETUP)] key.
10. The ARS Conguration name “Region “EXP” Type “B2”
will appear in the
bottom on the dis-
play.
11. Press [BAND(MHz)] key, then the message <FROM “B2”
TO “C2”> appears on the display.
12.Rotate the DIAL to select [OK?], and then press the
[DISP(SETUP)] key. The radio will re-start automatically.
Setting of the ARS feature to “Conguration C2” is suc-
cessfully complet-
ed.
TorestoretheARSfeaturesettingtothefactorydefault(B2),
performthesameproceduresabove.

1. Turn the transceiver ON.
2.
Press and hold the [F] (for FT5DE) or [DISP](for
FT3DE) key, then touch the [DISPLAY].
3. Rotate the DIAL knob to select “8 OPENING MESSAGE”
(for FT5DE) or “7 OPENING MESSAGE” (for FT3DE)
and then press the
[F] (for FT5DE) or [DISP](for
FT3DE) key .
4. Rotate the DIAL knob to select “MESSAGE” and then
press the
[F] (for FT5DE) or [DISP] (for FT3DE) key
.
5.
Enter “AH082M” (for FT5DE) or “AH072M” (for FT3DE) .
1) Touch the [abc]four times to select “A”, then touch
the [Æ].
2) Touch the [ghi] ve times to select “H”, then touch the
[Æ].
3) Touch the []to display the numeric keypad input
screen.
4) FT5DE: Touch the []à[8]à[]à[Æ].
FT3DE: Touch the []à[7]à[]à[Æ].
5)
Touch the [ABC]to display the alphabet input screen.
6) Touch the [mno]four times to select “M”.
6. Press the [PTT] switch, the screen that was shown when
the transceiver was turned ON will reappear on the dis-
play.
7. Turn the transceiver OFF.
8. Press and hold the []and [V/M●]
(for FT5DE) or []
and [GM]
(for FT3DE) keys while turning the transceiver
ON.
9. <TYPE : B2> appears in the display.
10.Rotate the DIAL knob to select <C2> and touch the
[WRITE]. The radio will re-start automatically. Setting
of the ARS feature to “Conguration C2” is successfully
completed.
TYPE : C2 TYPE : C2
FT5DE FT3DE
TorestoretheARSfeaturesettingtothefactorydefault(B2),
performthesameproceduresabove.

1. Turn the transceiver OFF.
2.
Press and hold the MONI/T.CALL key and the PTT switch
simultaneously, while turning the transceiver ON.
3. When the LCD backlight comes on, release the MONI/
T.CALL key and PTT switch.
4. Press the []à[]à[]keys.
The radio will re-start automatically. Setting of the ARS
feature to “Conguration C2” is successfully completed.
TorestoretheARSfeaturesettingtothefactorydefault(B2),
performthesameproceduresabove.

1. Turn the transceiver ON.
2. Press and hold the [F]key.
3. Rotate the DIAL knob to select “36 OPN.MSG” and then
press the [F]key.
4. Rotate the DIAL knob to select “MSG” and then press
the [V/M]key.
5. Enter “AH051M”.
1) Press the [] to select “A”.
2) Press the [4] two times to select “H”.
3) Press the [] to select “0”.
4) Press the []four times to select “5”.
5) Press the [1] to select “1”.
6) Press the [] to select “M”.
6. Press the [PTT] switch, the screen that was shown when
the transceiver was turned ON will reappear on the display.
7. Turn the transceiver OFF.
8. Press and hold the [HM/RV]and [GM] keys while turning
the transceiver ON.
9. <TYP.B2> appears in the display.
10.Rotate the DIAL knob to select
<TYP.C2> and touch the [F]key.
The radio will re-start automatical-
ly. Setting of the ARS feature to
“Conguration C2” is successfully completed.
TorestoretheARSfeaturesettingtothefactorydefault(B2),
performthesameproceduresabove.