Yakima Whispbar K780W User manual

K780W
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 6 x 6 x 6 x 6
x 6 x 1 x 1
Revision No: 1A 1

Fitting Kit K780W
MAX kgs (lbs)
W/P WHD
Ford
Transit Custom, 4dr Van 14-+ NZ 75 kgs (165 lbs) 75 kgs (165 lbs)
Transit Custom, 4dr Van 14-+ AU 75 kgs (165 lbs) 75 kgs (165 lbs)
Transit Custom, 4dr Van 14-+ EU 75 kgs (165 lbs) 75 kgs (165 lbs)
Transit Custom, 4dr Van 14-+ ZA 75 kgs (165 lbs) 75 kgs (165 lbs)
2

Fitting Kit K780W
X
A B C 1 2 3
Transit Custom, 4dr Van 14-+ (NZ) 95mm 1215mm 2100mm 1120mm 1120mm 1085mm
3 3/4ths" 47 13/16ths" 82 11/16ths" 44 1/8ths" 44 1/8ths" 42 11/16ths"
Transit Custom, 4dr Van 14-+ (AU) 95mm 1215mm 2100mm 1120mm 1120mm 1085mm
3 3/4ths" 47 13/16ths" 82 11/16ths" 44 1/8ths" 44 1/8ths" 42 11/16ths"
Transit Custom, 4dr Van 14-+ (EU) 95mm 1215mm 2100mm 1120mm 1120mm 1085mm
3 3/4ths" 47 13/16ths" 82 11/16ths" 44 1/8ths" 44 1/8ths" 42 11/16ths"
Transit Custom, 4dr Van 14-+ (ZA) 95mm 1215mm 2100mm 1120mm 1120mm 1085mm
3 3/4ths" 47 13/16ths" 82 11/16ths" 44 1/8ths" 44 1/8ths" 42 11/16ths"
3

Fitting Kit EN
K780W
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
●Use keys to remove covers.
4

Fitting Kit EN
K780W
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
●Adjust crossbar in or out to suit vehicle.
Refer to the crossbar instructions for
crossbar adjustment.
●Please check the front of this manual for
information relating specifically to your
vehicle.
5

Fitting Kit EN
K780W
●Tighten adjusting screw to 3 Nm (2.2 ft lb)
hand tight.
●Remove plastic clamp block by gripping bar
leg with fingers and push firmly with
thumbs until clamp block drops out behind
leg.
●Select plastic internal block (from fitting kit)
and insert into foot.
●Repeat for all legs.
6

Fitting Kit EN
K780W
●Refer to the underside of the pad for the
part number.
●Fit rubber pads (supplied with fitting kit) to
foot. Pad may vary in shape to that shown.
●Make sure the pad fits into the holes
underneath the foot.
●Remove fixed-point covers by turning the
plastic screw with flat-head screw driver.
7

Fitting Kit EN
K780W
Fitment
●Remove screws from the vehicle's fixed
points
●Repeat for all items.
●Fit the adaptor (A) to grubscrew (B).
●Use the following grubscrew lengths for
each position:
A = M6 x 35mm (1 3/8")
8

Fitting Kit EN
K780W
●Screw adaptor with grubscrew assembly
into roof. Tighten firmly.
●Repeat for all six positions.
●Place crossbar foot over clamp.
●Tighten the plastic knob.
●In the fully tightened position, the knobs
should be parallel with the vehicle.
●Tighten the black plastic knob.
9

Fitting Kit EN
K780W
●Check crossbar is securely attached to the
vehicle.
●Use keys to fit and lock covers
CAUTION: Recheck all fasteners immediately after
a load is applied to the crossbars.
Regularly check screws are tight.
10