YASKAWA PVI 36TL User manual

PVI 36TL
INSTALLATION AND OPERATION MANUAL
Revision H
© 2017, Yaskawa –Solectria Solar

PVI 36TL Installation and Operation Manual (Rev H)
DOCR-070588-H Page 2of 120
IMPORTANT REGISTRATION AND
WARRANTY INFORMATION
For warranty to become active, this inverter
must be registered. To activate warranty and
register inverter, please visit the link below.
www.solectria.com/registration

PVI 36TL Installation and Operation Manual (Rev H)
DOCR-070588-H Page 3of 120
Before You Start…
This manual contains important information regarding installation and safe operation
of the PVI 36TL. Be sure to read this manual carefully before using the inverter.
Thank you for choosing a Solectria grid-tied PV Inverter. This PV Inverter is high
performance and highly reliable product specifically designed for the North American
Solar market.
If you encounter any problems during installation or operation of this unit, first check
the user manual before contacting your local dealer or supplier. This user manual is
applicable for the following model: PVI 36TL.
Instructions inside this user manual will help you solve most installation and
operation difficulties. Contact your local supplier if the problem still exists.
Please keep this user manual on hand for quick reference.

PVI 36TL Installation and Operation Manual (Rev H)
DOCR-070588-H Page 4of 120
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
Please read this user manual carefully before product installation. Solectria reserves
the right to refuse warranty claims for equipment damage if the user fails to install the
equipment according to the instructions in this manual.
Warnings and Symbols in this Document
Markings on the Product
HIGH VOLTAGE:
This inverter works with high voltages. All work on the product must
only be performed as described in this document.
HOT SURFACE:
The equipment is designed to meet international safety standards,
but surfaces can become hot during operation. Do not touch the
heat sink or peripheral surfaces during or shortly after operation.
EARTH GROUND:
This symbol marks the location of grounding terminal, which must
be securely connected to the earth through the PE (Protective Earth)
cable to ensure operational safety.
DANGER:
DANGER indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
WARNING:
WARNING indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
CAUTION:
CAUTION indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
NOTICE:
NOTICE indicates a hazardous situation which, if not avoided,
could result in equipment working abnormally or property loss.
INSTRUCTION:
INSTRUCTION indicates important supplementary information
or provides skills or tips that can be used to help you solve a
problem or save you time.

PVI 36TL Installation and Operation Manual (Rev H)
DOCR-070588-H Page 5of 120
WARNING:
All of the installation and wiring connections should be performed
by qualified technical personnel. Disconnect the inverter from PV
modules and the AC Grid before maintaining and operating the
equipment.
Follow all local, national or country specific guidelines for electrical
safety.
DANGER:
Please disconnect the inverter from the AC grid and PV modules
before opening the equipment. Make sure hazardous high voltage
and energy inside the equipment has been discharged.
Do not operate or maintain the inverter until at least 5 minutes has
passed after disconnecting all sources from DC and AC sides.
CAUTION:
PVI 36TL inverter is approx. 66kg (145 pounds) including the wiring
box.
Please ensure the mounting bracket is properly installed before
hanging the inverter on the bracket.
INSTRUCTION:
Please check with your local electricity supply company before
selecting a grid standard. If the inverter is operated with a wrong
grid standard, the electricity supply company may cancel the
interconnection agreement.
Putting the inverter into operation before the overall system
complies with the national rules and safety regulation of the
application is not permitted.
DANGER!
Danger to life due to fire or explosion:
Despite careful construction, electrical devices can cause fires.
-Do not mount the inverter on flammable construction materials.
-Do not mount the inverter in areas where highly flammable
materials are stored.
-Do not mount the inverters in areas with a risk of explosion
SAVE THESE INSTRUCTIONS

PVI 36TL Installation and Operation Manual (Rev H)
DOCR-070588-H Page 6of 120
BEFORE YOU START… ........................................................................ 3
IMPORTANT SAFETY INSTRUCTIONS .......................................................... 4
1.0: OVERVIEW .......................................................................................... 9
1.1 INVERTER FOR GRID-TIED PV SYSTEMS .............................................. 9
1.2 PRODUCT FEATURES ....................................................................... 9
1.3 PRODUCT PROTECTION FUNCTIONS................................................. 10
1.4 CIRCUIT STRUCTURE DESIGN .......................................................... 10
1.5 APPEARANCE DESCRIPTION............................................................ 11
1.6 ANTI ISLANDING........................................................................... 12
1.7 DC GROUND FAULT PROTECTION .................................................... 12
1.8 SURGE SUPPRESSION .................................................................... 12
1.9 DC ARC FAULT DETECTION............................................................. 12
2.0: INSTALLATION ................................................................................... 12
2.1 RECOMMENDATIONS BEFORE INSTALLATION...................................... 14
2.2 MECHANICAL INSTALLATION ........................................................... 15
2.3 ELECTRICAL INSTALLATION.............................................................. 26
2.3.1 DC Connection.............................................................................28
2.3.2 AC and Ground Connection.........................................................37
2.4 INVERTER COMMUNICATION CONNECTIONS...................................... 41
2.4.1 Third Party Monitoring Systems Modbus Connections ...............43
2.4.2 SolrenView Data Logger Modbus Connections ...........................48
2.4.3 Preparing the Inverter for Modbus Communications .................58
2.4.4 Preparing the SolrenView Logger ...............................................59
2.4.5 Connecting Revenue Grade Meter to the SolrenView Logger .....61
2.4.6 Dry Contact Communication.......................................................65
3.0: COMMISSIONING.............................................................................. 69
3.1 COMMISSIONING CHECKLIST .......................................................... 69
3.1.1 Mechanical Installation...............................................................69
3.1.2 Cable Connections.......................................................................69
3.1.3 Electrical Check ...........................................................................69
3.2 COMMISSIONING STEPS................................................................. 69
4.0: USER INTERFACE ............................................................................... 72

PVI 36TL Installation and Operation Manual (Rev H)
DOCR-070588-H Page 7of 120
4.1 DESCRIPTION OF LCD.................................................................... 72
4.2 OPERATION STATE ........................................................................ 73
4.3 INTERFACE TYPES.......................................................................... 73
4.4 MENU FUNCTIONS........................................................................ 75
4.4.1 Operation information ................................................................75
4.4.2 Alarm ..........................................................................................77
4.4.3 History.........................................................................................78
4.4.4 System Configuration..................................................................79
4.4.5 Power dispatch............................................................................81
4.4.6 System Protection Parameters Setup..........................................81
4.4.7 System control parameters .........................................................83
4.4.8 Arc Fault Current Interruption.....................................................89
5.0: OPERATION ....................................................................................... 91
5.1 START-UP.................................................................................... 91
5.2 SHUTDOWN ................................................................................ 91
5.3 OPERATION MODE ....................................................................... 91
5.4 GRID-TIED POWER GENERATION..................................................... 93
6.0: MAINTENANCE AND DE-INSTALLATION ............................................. 94
6.1 FAULT SHUTDOWN AND TROUBLESHOOTING ..................................... 94
6.1.1 LED Fault and Troubleshooting ...................................................94
6.1.2 LCD fault and troubleshooting ....................................................94
6.2 PRODUCT MAINTENANCE .............................................................. 99
6.2.1 Check the Electrical Connection ..................................................99
6.2.2 Clean the Air Vent Filter ........................................................... 100
6.2.3 Replace Cooling Fans ............................................................... 100
6.2.4 Replace the Inverter ................................................................. 102
6.3 UNINSTALLING THE INVERTER ....................................................... 104
7.0: PRODUCT WARRANTY AND RMA POLICY ........................................ 105
8.: TECHNICAL DATA ............................................................................... 106
9.0: ACCESSORY OPTIONS ...................................................................... 110
9.1 FUSE BYPASS ...................................................................... 110
9.2 SHADE COVER .................................................................... 111
9.3 AC &DC DISCONNECT COVERS............................................. 114

PVI 36TL Installation and Operation Manual (Rev H)
DOCR-070588-H Page 8of 120
10.0: APPENDICES:................................................................................. 115
APPENDIX A–INSTRUCTION OF INVERTER SELECTION ............................ 115
APPENDIX B–PVI 36TL DATASHEET................................................... 119
APPENDIX C–STRING SIZING TOOL .................................................... 119
APPENDIX D–CONTACT INFORMATION ............................................... 119
APPENDIX E–AUTHORIZED DISTRIBUTORS........................................... 119
APPENDIX F–UL 1741 /UL 1699B/ IEEE 1547 /CSA 22.2#107.1
AUTHORIZATION TO MARK ................................................................ 120

PVI 36TL Installation and Operation Manual (Rev H)
DOCR-070588-H Page 9of 120
1.0: Overview
1.1 Inverter for Grid-Tied PV Systems
The PVI 36TL inverter is suitable for use for commercial and large scale PV
grid-tied systems. A system is generally made up of PV modules, DC power
distribution equipment, PV inverter and AC power distribution equipment (Figure 1.1).
The inverter converts DC from PV modules to AC with the same frequency and phase
as the AC grid. All or part of the AC power is supplied to local loads, and the surplus
power is supplied to the electricity grid.
DC power
distribution
equipments AC Grid
Bidirectional
electric meter
AC power
distribution
equipments
Figure 1.1 - Grid-Tied PV System
1.2 Product Features
High Conversion Efficiency: Advanced 3-level conversion technology; Max.
efficiency: 98.4%；CEC efficiency: 98.0%
Strong Grid Adaptability: 4 grid standards applicable; Reactive power
adjustable; Power Factor (PF) value: ±0.8, Remote Curtailment
Flexible Communication: Supports standard Modbus communications to
ensure compatibility with 3rd party monitoring and control systems
Wide DC Input Voltage Range: Operating DC Input Voltage Range:
200-950Vdc; Max DC input voltage: 1000V
Long Service Life: Uses thin-film capacitors to extend inverter’s service life
2 MPPTs: Dual and independent MPPT (Maximum Power Point Tracking)
enable maximum design flexibility and optimize energy harvest over the life of the
system
High Protection Degree: NEMA 4X protection degree meets the needs of both
indoor and outdoor use;
Intelligent Integration: Embedded DC/AC switches and up to 10 fused string
inputs eliminates the need for external combiner boxes and simplifies installation.

PVI 36TL Installation and Operation Manual (Rev H)
DOCR-070588-H Page 10 of 120
1.3 Product Protection Functions
Reverse polarity protection of DC input
Short circuit protection
Arc-Fault Circuit Interruption
Anti-islanding protection
Input and output over-voltage protection
Input over-current protection
Monitoring of DC input insulation against ground
Monitoring of AC output voltage and frequency
Monitoring of Leakage current against ground
Monitoring of DC injection from AC output
Monitoring of ambient temperature
Monitoring of IGBT module temperature
1.4 Circuit Structure Design
The basic schematic diagram of PVI 36TL inverter is shown in Figure 1.2.
The input of PV modules passes through surge protection circuitry, DC EMI wave filter,
and the front-end boost circuitry to achieve maximum power tracking and boost up
voltages. The output of the inverter converts the DC voltage to 3-phase AC voltage.
The high frequency AC components are removed with a wave filter. Then the 3-phase
AC voltage is passed through two-stage relays and EMI wave filter to produce high
quality AC power.
Figure 1.2 - Schematic Diagram of PVI 36TL Inverter

PVI 36TL Installation and Operation Manual (Rev H)
DOCR-070588-H Page 11 of 120
1.5 Appearance Description
Figure 1.3 - Sketch of PVI 36TL Inverter
Main Items of the Inverter:
1) Main inverter section
2) Wiring box of the inverter
3) Mounting bracket
4) External cooling fans
5) LED indication lights
6) LCD
7) Key buttons
8) DC switch: DC power on/off
9) AC switch: AC power on/off

PVI 36TL Installation and Operation Manual (Rev H)
DOCR-070588-H Page 12 of 120
1.6 Anti Islanding
This inverter includes Active Anti-Islanding detection as required by
UL1741/IEEE1547. The inverter will automatically make small variations in reactive
power output in order to detect a possible islanding condition. If the grid is stable,
these small variations will have negligible effects on system voltage and frequency.
However, in an islanded condition the small amount of reactive power changes will
force the system voltage or frequency to change significantly, which will trigger the
inverter to shut down.
1.7 DC Ground Fault Protection
The PVI 36TL includes residual current detection as part of the DC ground fault
detection method as required by UL1741. If there is a ground fault in the array, the
ground fault detection technology will detect the array leakage current. The
inverter will shut down if the leakage current exceeds 500mA.
1.8 Surge Suppression
"Standard 1.2/50 μs - 8/20 us Combination Wave"
"Standard 0.5 μs - 100 kHz Ring Wave"
1.9 DC Arc Fault Detection
The PVI 36TL includes DC Arc fault detection compliant with UL 1699B. The inverter
detects electrical noise that typically accompanies a DC series arc. The inverter will
shut down should the arc fault sensor detect a series arc. See section “Arc fault
current interruption” for more details.
2.0: Installation
Below is the installation procedure for the inverter. Please read carefully and install the
product step-by-step.
Before installation, please check that the following items are included in the package:
STANDARD WAVEFORM PEAK VALUES
Surge Category
Ring Wave
Combination Wave
B
6 kV/0.50 kA
6 kV/3 kA

PVI 36TL Installation and Operation Manual (Rev H)
DOCR-070588-H Page 13 of 120
Table 2.1 - Main Items
No.
Item
Qty
Note
(1)
Main inverter
section
1
(2)
Wiring box
1
(3)
Mounting bracket
1
Upon which inverter is hung and
mounted onto a wall
(4)
User manual
1
Installation and operation manual
(5)
Accessory kit
1
Contains all necessary accessories
The (5) Accessory kit contains items listed below:
Table 2.2 - Accessories
No.
Item
Qty
Note
(1)
M8 Expansion tubes
8
For mounting bracket
(2)
M8×25 assembling
bolts
8
For mounting bracket
(3)
M6 X16 screw
6
For wiring box and main section; 2
spare parts
(4)
M5X10 screw
8
8 for mounting bracket and inverter,
external ground connection;
(5)
M5 flange nut
2
For internal ground stud connection; 1
spare part
(6)
Lifting eye nut M10
2
For lifting the main section
(7)
OT type terminal
2
For ground connection
(8)
Pre-insulated end
5
For AC output cables, 1 spare part

PVI 36TL Installation and Operation Manual (Rev H)
DOCR-070588-H Page 14 of 120
ferrule for AC side
(4 AWG)
(9)
Pre-insulated end
ferrule for grounding
(8AWG)
8
For AC ground cables
(10)
Pre-insulated end
ferrule for DC side
(10 AWG)
20
For DC input cables
(11)
RJ45 connecter
4
For RS-485 or Ethernet communication,
2 spare parts
(12)
5 pin connector
1
For RS-485 communication
(13)
3 pin connector
1
For dry contact communication
2.1 Recommendations before Installation
Check that the product environmental specifications (protection degree,
operating temperature range, humidity and altitude, etc.) meet the requirements of
the specific project location;
Make sure that the AC grid voltage is within the normal range.
Ensure that the local electricity supply authority has granted permission to
connect to the grid.
Installation personnel must be qualified electricians or people who have
received professional training.
Sufficient space according to Figure 2.3 should be provided to allow the
inverter cooling system to operate normally.
Install the inverter away from flammable and explosive substances.
Avoid installing the inverter in locations that exceed the temperature limits
specified in the inverter data sheet to limit undesirable power loss.
Do not install the inverter near the electromagnetic source which can
compromise the normal operation of electronic equipment.
INSTRUCTION:
The items in the accessory kit table above are for the standard
configuration. The accessories may vary if optional parts are purchased.

PVI 36TL Installation and Operation Manual (Rev H)
DOCR-070588-H Page 15 of 120
2.2 Mechanical Installation
1) Dimensions
Figure 2.1 - PVI 36TL Inverter Dimensions

PVI 36TL Installation and Operation Manual (Rev H)
DOCR-070588-H Page 16 of 120
2) Installation Method (see Figure 2.2):
Make sure that the mounting structure (wall, rack, etc.) is suitable to support
the inverter weight. Follow the mounting guidelines below:
(a) If the location permits, install the inverter vertically.
(b) If the inverter cannot be mounted vertically, it may be tilted backward but
no lower than 15 degrees from horizontal.
The shade cover option must be purchased and installed for any
installation angles of 75° or less.
(c) Do NOT mount the inverter leaning forward.
(d) Do NOT mount the inverter in a horizontal position (<15 degrees).
(e) Do NOT mount the inverter upside down.
Figure 2.2 - Inverter Mounting
WARNING: Do not install the inverter tilted forward, lying on its back, or upside
down as shown in Figure 2.2 c, d and e.
WARNING: Shade covers are required for inverters installed at angles 75° or
less.

PVI 36TL Installation and Operation Manual (Rev H)
DOCR-070588-H Page 17 of 120
3) Installation Space Requirement (see Figure 2.3):
The distances between the inverters or the surrounding objects should meet
the following conditions:
Figure 2.3 - Inverter Wall Mounting Specifications
NOTICE:
The spacing between two adjacently mounted inverters should be
≥500mm (19.7 inches). Ensure that the air space around the inverter is
well ventilated.
NOTICE:
The installation clearance between two inverters needs to be increased
to 30 in. when the ambient temperature is higher than 45°C.

PVI 36TL Installation and Operation Manual (Rev H)
DOCR-070588-H Page 18 of 120
Figure 2.4 - Inverter Pillar Mounting Specifications
7.9in
¡ Ý200mm
11.8in
¡ Ý300mm
23.6in
¡ Ý600mm
11.8in
¡ Ý300mm
11.8in
¡ Ý300mm
INSTRUCTION:
If the inverter is installed on Unistrut or the array racking (instead of
solid wall), the space from the bottom of one inverter to the top of the
inverter below may be as small as 4in (100mm).

PVI 36TL Installation and Operation Manual (Rev H)
DOCR-070588-H Page 19 of 120
4) Mounting the Inverter Onto the Bracket
(1) Mark the 8 holes on the bearing surface for mounting the bracket as shown
in Figure 2.5;
813mm(min.)
425mm(min)
250mm
550mm(min.)
522mm
140mm(5.51in.)
1100mm(min.)
(21.7in.) (9.84in.)
250mm
(9.84in.)
(16.7in.)
(32in.)
(43.3in.)
(20.55in.)
Figure 2.5 - Holes on the Bearing Surface Dimensions
(2) Drill holes at the marked positions with a 10mm (0.4in.) drill and put the M8
expansion tubes① into the holes; fasten the mounting bracket② with the
M8x25 assembling bolts③in the accessory kit. Figure 2.6.
Tool: Electric drill (Ф10mm/0.4in. head), 13mm wrench 240 in-lbs

PVI 36TL Installation and Operation Manual (Rev H)
DOCR-070588-H Page 20 of 120
1
2
3
Figure 2.6 - Securing the Mounting Bracket
(3) Hang the inverter onto the mounting bracket as shown in Figure 2.7 and
Figure 2.8;
Lift mounting: Take out the lifting eye nut M10 (2pcs) from the accessory kit,
and screw them onto the studs at the top of the inverter. Use a sling rope or
bar (inserted through both lifting eye nuts) to lift the inverter onto the
bracket. The minimum angle between the two sling ropes should be less
than 90 degrees.
Manual mounting: Two people are needed to properly lift the inverter by the
handles detailed in Figure 2.8, and mount the inverter onto the bracket.
Figure 2.7 - Mounting the Main Inverter Section on the Bracket
CAUTION:
The main PVI 36TL inverter section is 55kg (≈122 pounds).
Please ensure the mounting bracket is properly installed before
hanging the inverter on the bracket. It is recommended to have at
least 2 people to mount the inverter due to the weight of the
equipment.
1
2
3
9.84in. 9.84in.
20.55in.
5.51in.
(140mm) (522mm)
(250mm) (250mm)