YitaHome HNXD-V1 User manual

ASSEMBLY INSTRUCTIONS
SAFE BOX
HNXD-V1
IMISSB-0010

ASSEMBLY INSTRUCTIONS
1
B
C
D
Item no. Reference Image Qty.
X1
X6
X1
1.Confirm all parts are present prior to assembly.
2.Do not lock the emergency key or emergency battery box into the cabinet.
AX2
Emergency key
Emergency battery box
Expansion screw
Fireproof bag

ASSEMBLY INSTRUCTIONS
2
1.Position the cabinet near the wall and mark the locations of the anchor holes
using a marker.
2.Use a hammer drill to create holes at the marked positions.
3.Move the cabinet to its designated location and insert expansion screws into
the drilled holes with a hammer.
4.Tighten the expansion screws securely to complete the installation.
Mail slot
How to Mount the Safe:
13
2
4
Operation panel Internal
battery box

ASSEMBLY INSTRUCTIONS
3
User Manual for Electronic Lock
Lock hole cover
Door handle
Key panel
Setting button
First-Time Safe Setup:
1. Unfasten the right side panel and use the emergency key to open the safe.
（The keyhole cover slides laterally）
2. Install the batteries.
3. Set the password (refer to the detailed instructions in the following).

ASSEMBLY INSTRUCTIONS
4
4. Vibration alarm setting
4.1.Vibration alarm electronic lock alarm has the function of setting alert and
eliminating alert.
3. Turn on the safe
3.1.Touch the touch screen and enter the password you set.
3.2.Press "#" key to confirm, the door indicator light is on, the buzzer drops twice,
indicating that the password input is correct.
2.Group 2 password setting:
touch and wake up the touch screen, press 00, then press the setting button in the
box (change code switch), then enter the new password and confirm the end
with the # number key.
The default password of the electronic lock is "123456"
1. Password settings and changes
1.1.Press the setting button in the box (code switch), the buzzer drops and touch l
ight on.
1.2.Enter the password you need, length 3-12 bits.
1.3.Press "#" key to confirm that the buzzer rang long, the light goes out,
indicating that the password setting and change success
User Manual for Electronic Lock

ASSEMBLY INSTRUCTIONS
5
4.2.Set the alert method: first touch and wake up the touch screen, and press
the "*" key to the computer board to automatically enter the alert state.
Alert the safe immediately after the vibration.
4.3.Remove the alert method: after the safe box alarm, enter the set password,
press the "#" key to open the door to eliminate the alert.
5. Underpressure indication:
5.1.The system uses four 1.5V alkaline batteries. If the voltage is insufficient, the
door will continuously remind "drop, drop, di"."Drop, drop, drop" twice, the
power indicator flashes for about 30 seconds to close, remind the user to
replace the battery in time.
5.2.If the battery voltage is insufficient, you can use the emergency power supply
or the mechanical emergency key for operation.
5.3. This electronic lock has the function of power loss protection password never
disappearing.
6.Alarm operation
This electronic lock has 3 (5) password errors, automatic alarm for 30 seconds or
1 minute, enter the correct password can eliminate the alarm sound.
7.Sound on and off
Touch to wake up the touch screen, enter "11#", the buzzer "drop ~" a long sound,
that is, turn on or off all the sound success!

ASSEMBLY INSTRUCTIONS
6
G
9. Technical parameters:
1、Working power supply: four no. 5 "AA" alkaline batteries
2、Operating voltage range: 4.2V-7V
3、Working underpressure point: 4.6V ± 0.20V
4、Operating current: 380 mA
5、Static current was <35 uA
8.system initialization
Long press the setting button on the mechanism for 5 seconds, the system will
resume the initialization settings and clear all passwords.

Pure & Easy