YOKOGAWA SL1000 User manual

IM 720120-01E
8th Edition
High-Speed Data Acquisition Unit
SL1000

Product Registration
Thank you for purchasing YOKOGAWA products.
YOKOGAWA provides registered users with a variety of information and services.
Please allow us to serve you best by completing the product registration form
accessible from our website.
http://tmi.yokogawa.com/
PIM 103-04E

i
IM 720120-01E
Thank you for purchasing the SL1000 High-Speed Data Acquisition Unit. This user’s
manual contains useful information about the instrument’s functions and operating
procedures and lists the handling precautions of the SL1000. To ensure correct use,
please read this manual thoroughly before beginning operation.
Keep this manual in a safe place for quick reference in the event a question arises. This
manual will come in handy when you are unsure of how to operate the product.
List of Manuals
The following manuals, including this one, are provided as manuals for the SL1000.
Please read all of them.
Manual Title Manual No. Description
SL1000
High-Speed Data Acquisition Unit
User’s Manual
IM 720120-01E This manual. Explains all functions and
procedures of the SL1000 excluding the
communication functions.
SL1000 Acquisition Software
User’s Manual
IM 720120-61E Explains all functions and procedures of the
Acquisition Software used to configure and
control the SL1000.
SL1000 Input Module
User’s Manual
IM 720120-51E Explains the specifications of the input
modules that can be installed in the SL1000.
Precautions Concerning the
Modules
IM 701250-04E The manual explains the precautions
concerning the modules.
701992 Xviewer Install Manual IM 701992-02E This manual explains how to install the
Xviewer*setup software.
SL1000
High-Speed Data Acquisition Unit
IM 720120-92 Document for China
The “E” in the manual numbers are the language codes.
* The Xviewer user’s manual is included in the Xviewer help.
Refer to the “Optional Accessories (Sold Separately)” about the accessory’s manual No..
Contact information of Yokogawa offices worldwide is provided on the following sheet.
Document No. Description
PIM 113-01Z2 List of worldwide contacts
Notes • The contents of this manual are subject to change without prior notice as a result of
continuing improvements to the instrument’s performance and functions. The figures
given in this manual may differ from those that actually appear on your screen.
• Every effort has been made in the preparation of this manual to ensure the accuracy
of its contents. However, should you have any questions or find any errors, please
contact your nearest YOKOGAWA dealer.
• Copying or reproducing all or any part of the contents of this manual without
YOKOGAWA’s permission is strictly prohibited.
• The TCP/IP software of this product and the document concerning the TCP/IP
software have been developed/created by YOKOGAWA based on the BSD Networking
Software, Release 1 that has been licensed from University of California.
Trademarks • Microsoft, Windows, Windows XP, Windows Vista, Windows 7, and Windows 8 are
either registered trademarks or trademarks of Microsoft Corporation in the United
States and/or other countries.
• Adobe and Acrobat are trademarks of Adobe Systems Incorporated.
• GIGAZoom ENGINE are pending trademark of Yokogawa Electric Corporation.
• For purposes of this manual, the ® and TM symbols do not accompany their
respective registered trademark names or trademark names.
• Other company and product names are registered trademarks or trademarks of their
respective holders.
8th Edition: July 2017 (YMI)
All Rights Reserved, Copyright © 2007 Yokogawa Electric Corporation
All Rights Reserved, Copyright © 2012 Yokogawa Meters & Instruments Corporation

ii IM 720120-01E
Revisions • 1st Edition: December 2007
• 2nd Edition: September 2008
• 3rd Edition: July 2012
• 4th Edition: September 2013
• 5th Edition: July 2014
• 6th Edition: October 2015
• 7th Edition: February 2016

iii
IM 720120-01E
Checking the Contents of the Package
Unpack the box and check the contents before operating the instrument. If some of the
contents are not correct or missing or if there is physical damage, contact the dealer from
which you purchased them.
SL1000 Check that the model name and suffix code given on the name plate on the rear panel
match those on your order.
TRIG OUT TRIG IN
POWER
ON OFF
100-120 V
220-240 V AC
300 VA MAX 50/60 Hz
GROUP UNIT SERVICE GO NOGO ALARM REMOTE SYNC OUT SYNC IN
LINK
ACT
ETHERNET
1000BASE-T
MODEL Suffix Code1Description
720120 SL1000 High-Speed Data Acquisition Unit
8 slots, up to 128 MW memory
With 1 license for the Xviewer Standard Edition (701992-SP01)
Power cord2-D UL/CSA Standard power cord, Maximum rated voltage: 125 V
-F VDE Standard power cord, Maximum rated voltage: 250 V
-Q BS Standard power cord, Maximum rated voltage: 250 V
-R AS Standard power cord, Maximum rated voltage: 250 V
-H GB Standard power cord, Maximum rated voltage: 250 V
Options /HD1 500-GB internal HDD
/C10 Ethernet interface
/P4 Four probe power outputs
/XV0 Xviewer Less3, 4
/XV1 Xviewer MATH Edition (701992-GP01)4
1 For products whose suffix code contains “Z,” an exclusive manual may be included. Please read
it along with the standard manual.
2 Make sure that the attached power cord meets the designated standards of the country and area
that you are using it in.
3 Xviewer required to access the internal hard disk via USB.
4 The /XV0 and /XV1 options cannot be specified simultaneously.
No. (Instrument No.)
When contacting the dealer from which you purchased the instrument, please give them
this number.

iv IM 720120-01E
Standard Accessories
The standard accessories below are supplied with the instrument. Check that all contents
are present and undamaged.
Model Part Number Qty. Specifications
Power cord1A1006WD 1 UL/CSA Standard power cord
Maximum rated voltage: 125 V, Maximum rated current: 7 A
A1009WD VDE Standard Power Cord
Maximum rated voltage: 250 V, Maximum rated current: 10 A
A1054WD BS Standard Power Cord
Maximum rated voltage: 250 V, Maximum rated current: 10 A
A1024WD AS Standard Power Cord
Maximum rated voltage: 250 V, Maximum rated current: 10 A
A1064WD GB Standard Power Cord
Maximum rated voltage: 250 V, Maximum rated current: 10 A
Acquisition Software (CD)2B8073ZA 1 Acquisition software used to configure and control the SL1000.
Soft case B8081HG 1 For storing accessories.
Cover panels B8073CY 8 For protecting empty module slots.
Rubber feet A9088ZM 2 Two rubber feet in one set.
Manuals IM 720120-01E 1 High-Speed Data Acquisition Unit User’s Manual (this manual)
IM 720120-61E 1 Acquisition Software User’s Manual
IM 720120-51E 1 Input Module User’s Manual
IM 701250-04E 1 Precautions Concerning the Modules
IM 701992-02E 1 Xviewer Install Manual3
IM 720120-92 1 User’s Manual for China
PIM 113-01Z2 1 List of worldwide contacts
Standard accessories are not covered by warranty of this instrument.
ManualsAcquisition
Software
B8073ZA (CD)2
Soft case
B8081HG
Cover panels
B8073CY 8 pieces
Rubber feet
A9088ZM
UL/CSA Standard
A1006WD
VDE Standard
A1009WD
BS Standard
A1054WD
AS Standard
A1024WD
DFQR
Power Cord1(one of the following power cords is
supplied according to the instrument’s suffix codes)
GB Standard
A1064WD
H
1 Make sure that the attached power cord meets the designated standards of the country and area
that you are using it in.
2 The CD includes 1 license for the Xviewer Standard Edition in addition to the SL1000 Acquisition
Software.
The /XV1 option includes 1 license for the Xviewer MATH Edition.
The /XV0 option does not include a license for Xviewer.
3 Not included with the /XV0 option.
Checking the Contents of the Package

v
IM 720120-01E
Modules (Sold Separately)
Check that the MODEL indicated on the module is what you ordered.
MODEL Name Minimum Q’ty Abbreviation
720210 High-Speed 100 MS/s, 12-Bit Isolation Module (2CH) 1 HS100M12
720211 High-Speed 100 MS/s, 12-Bit Isolation Module (2CH) 1 HS100M12
701250 High-Speed 10 MS/s, 12-Bit Isolation Module 1 HS10M12
720250 High-Speed 10 MS/s, 12-Bit Isolation Module 1 HS10M12
701251 High-Speed High-Resolution 1 MS/s, 16-Bit Isolation Module 1 HS1M16
701255 High-Speed 10 MS/s, 12-Bit Non-Isolation Module 1 NONISO_10M12
701267 High-Voltage 100 kS/s, 16-Bit Isolation Module (with RMS) 1 HV(with RMS)
720268 High-Voltage 1 MS/s, 16-Bit Isolation Module (with AAF, RMS) 1 HV(AAF, RMS)
701261 Universal (Voltage/Temp.) Module 1 UNIVERSAL
701262 Universal (Voltage/Temp.) Module (with AAF) 1 UNIVERSAL(AAF)
701265 Temperature, High Precision Voltage Isolation Module 1 TEMP/HPV
720266 Temperature, High Precision Voltage Isolation Module
(low noise)
1 TEMP/HPV
701270 Strain Module (NDIS) 1 STRAIN_NDIS
701271 Strain Module (DSUB, Shunt-Cal) 1 STRAIN_DSUB
701275 Acceleration/Voltage Module (with AAF) 1 ACCL/VOLT
701281 Frequency Module 1 FREQ
720281 Frequency Module 1 FREQ
Top line: Model
Bottom line: Abbreviated name
The location varies depending on the module.
701250
HS10M12
This user’s manual refers to the input modules by MODEL (abbreviation).
For example, the High-Speed 10 MS/s, 12-Bit Isolation Module is indicated as 701250
(HS10M12). However, the module may be indicated only by the model (701250) if a
description about the same module is given immediately before it.
Checking the Contents of the Package

vi IM 720120-01E
Optional Accessories (Sold Separately)
The optional accessories below are available for purchase separately.
• Use the accessories specified in this manual. Moreover, use the accessories of this
product only with Yokogawa products that specify them as accessories.
• Use the accessories of this product within the rated range of each accessory. When
using several accessories together, use them within the specification range of the
accessory with the lowest rating.
Name Part
Number Safety standard Specifications Manual No.
Isolated Probe 700929 1000Vrms-CAT II For the 701250, 701251, 720210, and 720211,
(10:1)
IM 700929-01E
701947 1000 Vrms CAT II 100:1 safety probe for the 701250, 701251,
720210, and 720211
IM 701947-01E
Current Probe 701930 300 Vrms CAT III 150 Arms, DC to 10 MHz, used by connecting
to the Probe Power Terminal (/P4 option) or the
Probe Power Supply (701934) sold separately
IM 701930-01E
701931 300 Vrms CAT III 500 Arms, DC to 2 MHz, used by connecting to
the Probe Power Terminal (/P4 option) or the
Probe Power Supply (701934) sold separately
IM 701931-01E
701932 300 Vrms 30 Arms, DC to 100 MHz. Used by connecting to
a probe power terminal (/P4 option) or a probe
power supply (701934; sold separately).
IM 701932-01E
701933 300 Vrms 30 Arms, DC to 50 MHz, used by connecting to
the Probe Power Terminal (/P4 option) or the
Probe Power Supply (701934) sold separately
IM 701933-01E
701917 Vrms 5 Arms, DC to 50 MHz. Used by connecting to
a probe power terminal (/P4 option) or a probe
power supply (701934; sold separately).
IM 701917-01EN
701918 Vrms 5 Arms, DC to 120 MHz. Used by connecting to
a probe power terminal (/P4 option) or a probe
power supply (701934; sold separately).
IM 701917-01EN
10:1 Passive Probe 701940 — For non-isolated input on the 701255: 600 V or
less
For isolated input other than above: 42 V or less
IM 701940-01E
702902 1000V
(DC+ACpeak)
CAT II
10:1 safety probe, wide temperature range, for
isolated BNC input, for the 701250, 701251,
720210, and 720211
IM 702902-01E
Differential Probe 700924 1000 Vrms CAT III Switchable between 1000:1 and 100:1
Measurable voltage: 1400 Vpeak (1000 Vrms)
IM 700924-01E
700925 1000V
(DC+ACpeak)
CAT III
Switchable between 100:1 and 10:1
Measurable voltage: 500 Vpeak (350 Vrms)
IM 700925-01E
701926 1000 Vrms CAT III Switchable between 1000:1 and 100:1
Measurable voltage: 7000 Vpeak (5000 Vrms)
IM 701926-01E
1:1 BNC Safety Adapter
Lead
701901 1000Vrms-CAT II For the 701250, 701251, 720210, and 720211.
Used with the 701954, B9852MM, B9852MN,
758922, 758929, or 758921 sold separately
—
1:1 Safety Adapter Lead 701904 1000 Vrms CAT II
600 Vrms CAT III
For use with the 701267 and 720268. Used with
the following items (which are sold separately):
the 701954, B9852MM, B9852MN, 758922,
758929, or 758921.
—
Measurement Lead 758933 1000Vrms CAT III 1 m, for the 701260. Used with the 701954,
B9852MM, B9852MN, 758922, 758929, or
758921 sold separately
—
Alligator Clip (dolphin type) 701954 1000Vrms CAT III Two pieces in one set (red/black) —
Safety Mini-clip (hook type) B9852MM 1000 Vrms CAT III Black —
B9852MN 1000 Vrms CAT III Red —
Alligator Clip Adapter 758922 300Vrms CAT II Two pieces in one set —
758929 1000Vrms CAT II Two pieces in one set —
Fork Terminal Adapter 758921 1000Vrms CAT II Two pieces in one set (red/black). For 4 mm
screws.
—
Checking the Contents of the Package

vii
IM 720120-01E
Name Part
Number Safety standard Specifications Manual No.
Cable* 366926 — Non-isolated: 42 V or less, for the 701250,
720250, 701251, 701255, 720210, and 720211, 1
m
—
Banana-Alligator Clip Cable 366961 — Non-isolated: 42 V or less, for the 701261,
701262, 701265, and 720266, 1.2 m
—
Safety BNC Cable (1 m) 701902 1000Vrms CAT II 1000Vrms-CAT II (BNC-BNC) —
Safety BNC Cable (2 m) 701903 1000Vrms CAT II 1000Vrms-CAT II (BNC-BNC) —
Safety BNC-to-Banana
Adapter
758924 500Vrms CAT II For the 701250, 701251, 701255, 720210, and
720211
—
Probe Power Supply 701934 — Large current output, power supply for external
probes (4 outputs)
IM 701934-01E
Shunt Resistor 438920 — 250 Ω ± 0.1% —
438921 — 100 Ω ± 0.1% —
438922 — 10 Ω ± 0.1% —
Bridge Head 701955 — NDIS, bridge resistance: 120 Ω, with a 5-m cable IM 701955-01E
701956 — NDIS, bridge resistance: 350 Ω, with a 5-m cable
701957 — DSUB, bridge resistance: 120 Ω, shunt-cal
support, with a 5-m cable
IM 701957-01E
701958 — DSUB, bridge resistance: 350 Ω, shunt-cal
support, with a 5-m cable
Plug-on clip 701948 1000Vrms CAT II For the 700929/701947 IM 701948-01E
Long test clip 701906 1000Vrms CAT III For the 700924/701926 IM 701906-01E
Synchronous Connecting
Cable
720901 — -01: for synchronous SL1000 operation (1 m) —
-02: for synchronous SL1000 operation (3 m) —
Rack Mounting Kit 751541 — -J4: Rack mounting kit for SL1000 (JIS) IM 751541-J4-01E
-E4: Rack mounting kit for SL1000 (EIA) IM 751541-E4-01E
Sold individually.
*Use cables (366926) that YOKOGAWA has been shipping since February 4, 1998. Cables (366926) shipped before this date
cannot be used in combination with the SL1000 input modules.
Optional accesories(sold separately) are not covered by warranty of this instrument.
Checking the Contents of the Package

viii IM 720120-01E
1:1 BNC Safety
Adapter Lead
701901*
Cable
366926
Banana-Alligator
Clip Cable
366961
Isolated Probe
701947
Current Probe
701930
Current Probe
701933
Alligator Clip Adapter
758922
Alligator Clip Adapter
758929
Isolated Probe
700929
10:1 Passive Probe
701940
Alligator Clip
(dolphin type)
701954
Fork Terminal
Adapter
758921
Current Probe
701931
Safety BNC Cable
(1 m) 701902
Safety BNC Cable
(2 m) 701903
Safety
BNC-to-Banana
Adapter
758924
Bridge Head
701955 (NDIS, 120 Ω)
Bridge Head
701956 (NDIS, 350 Ω)
Bridge Head
701957 (DSUB, 120 Ω)
Bridge Head
701958 (DSUB, 350 Ω)
* The 1:1 BNC safety adapter lead (701901/701904) is used in combination with the following accessories sold
separately: alligator clip (dolphin type 701954), safety mini-clip (hook type: B9852MM and B9852MN),
alligator adapter (758922 or 758929), and/or the fork terminal adapter (758921).
Probe Power
Supply
701934
Synchronous
Connecting Cable
720901-01 (1 m)
720901-02 (3 m)
Current Probe
701932
10:1 Passive Probe
(wide temperature range)
702902
PROBE 1 PROBE 2 PROBE 3 PROBE 4
OUTPUT
POWERSUPPLY
Plug-on clip
701948
Long test clip
701906
Safety miniclip
(hook type)
B9852MM
B9852MN
Differential probe
700924
Differential probe
700925
Differential probe
701926
1:1 Safety
Adapter Lead
7019041
Current probe
701918
Current probe
701917
Checking the Contents of the Package

ix
IM 720120-01E
Safety Precautions
This product is designed to be used by a person with specialized knowledge.
This instrument is an IEC safety class I instrument (provided with a terminal for protective
earth grounding).
The general safety precautions described herein must be observed during all phases
of operation. If the instrument is used in a manner not specified in this manual, the
protection provided by the instrument may be impaired. Yokogawa Electric Corporation
assumes no liability for the customer’s failure to comply with these requirements.
This manual is an essential part of the product; keep it in a safe place for future
reference.
The following symbols are used on this instrument.
Warning: handle with care. Refer to the user’s manual or service manual.
This symbol appears on dangerous locations on the instrument which require
special instructions for proper handling or use. The same symbol appears in the
corresponding place in the manual to identify those instructions.
Protective grounding or protective grounding terminal
Ground (earth) or functional ground terminal (do not use this terminal as a
protective ground terminal.)
Alternating current
Direct current
ON (power)
OFF (power)
French
Avertissement : À manipuler délicatement. Toujours se reporter aux manuels
d’utilisation et d’entretien. Ce symbole a été apposé aux endroits dangereux de
l’instrument pour lesquels des consignes spéciales d’utilisation ou de manipulation
ont été émises. Le même symbole apparaît à l’endroit correspondant du manuel
pour identifier les consignes qui s’y rapportent.
Mise à la terre de protection ou borne de mise à la terre de protection
Borne de terre ou borne de terre fonctionnelle (ne pas utiliser cette borne comme
prise de terre.)
Courant alternatif
Courant direct
Marche (alimentation)
Arrêt (alimentation)

xIM 720120-01E
Failure to comply with the precautions below could lead to injury or death or
damage to the instrument.
WARNING
Use the Instrument Only for Its Intended Purpose
This instrument is a data aquisition device that measures electrical signals. Do not
use this instrument for anything other than as a data aquisition device.
Check the Physical Appearance
Do not use the instrument if there is a problem with its physical appearance.
Use the Correct Power Supply
Before connecting the power cord, ensure that the source voltage matches the
rated supply voltage of the instrument and that it is within the maximum rated
voltage of the provided power cord.
Use the Correct Power Cord and Plug
To prevent electric shock or fire, be sure to use the power cord supplied by
YOKOGAWA. The main power plug must be plugged into an outlet with a protective
earth terminal. Do not disable this protection by using an extension cord without
protective earth grounding. Additionally, do not use the power cord supplied with
this instrument with another instrument.
Connect the Protective Grounding Terminal
Be sure to connect the protective earth to prevent electric shock before turning ON
the power. The power cord that comes with the instrument is a three-prong type
power cord. Connect the power cord to a properly grounded three-prong outlet.
Do Not Impair the Protective Grounding
Never cut off the internal or external protective earth wire or disconnect the wiring
of the protective earth terminal. Doing so poses a potential shock hazard.
Do Not Operate with Defective Protective Grounding or Fuse
Do not operate the instrument if the protective earth or fuse might be defective.
Also, make sure to check them before operation.
Do Not Operate in an Explosive Atmosphere
Do not operate the instrument in the presence of flammable liquids or vapors.
Operation in such an environment constitutes a safety hazard.
Do Not Remove the Covers or Disassemble or Alter the Instrument
Only qualified YOKOGAWA personnel may remove the covers and disassemble or
alter the instrument. The inside of the instrument is dangerous because parts of it
have high voltages.
Ground the Instrument before Making External Connections
Securely connect the protective grounding before connecting to the item under
measurement or to an external control unit. If you are going to touch the circuit,
make sure to turn OFF the circuit and check that no voltage is present.
Precautions to Be Taken When Using the Modules
• Do not apply input voltage exceeding the maximum input voltage, withstand
voltage, or allowable surge voltage.
• To prevent electric shock, be sure to furnish protective earth grounding of the
instrument.
• To prevent electric shock, be sure to fasten the module screws. Otherwise, the
electrical protection function and the mechanical protection function will not be
activated.
Safety Precautions

xi
IM 720120-01E
• Avoid continuous connection under an environment in which the allowable surge
voltage or greater voltage may occur.
• Be careful not to exceed the maximum input voltage of a module in the following
cases.
• When the probe attenuation is 1:1.
• When the module input coupling is set to AC.
A DC voltage at the same electric potential as the probe input is applied to the
module input.
Precautions to Be Taken When Using the Probes
• To measure high voltage with the 720210 (HS100M12), 720211 (HS100M12),
701250 (HS10M12), 720250 (HS10M12), or 701251 (HS1M16), use the
isolated probes (700929, 701947), passive probes 702902, or 1:1 safety cables
(combination of 701901 and 701954).
• If you are using the 701255 (NONISO_10M12), be sure to fasten the module
screws. Fastening the module screws activates the protection function and the
non-isolation function. It is extremely dangerous if you do not fasten the screws.
In addition, if you are measuring high voltage above 42 V, be sure to use the
passive probe 701940.
• The BNC part of the passive probe 701940 is made of metal. Therefore, use
the probe at 42 V or less for isolated inputs (720210 (HS100M12), 701250
(HS10M12), 701251 (HS1M16)), etc.) for safety reasons. (Do not connect
voltage above 42 V to both the High and Low sides.) For non-isolated inputs
(701255 (NONISO_10M12), etc.), fasten the module screws as described
before.
• If you are measuring high voltages using the 701267 (HV (with RMS), or 720268
(HV (AAF, RMS)), use the measurement leads (combination of 758933 and
701954) or 1:1 safety cables (combination of 701904 and 701954).
• The measurement category of the 701267 (HV (with RMS)) is 400V-CAT II
for the low side and 700V-CAT II for the high side. Use caution because the
overvoltage tolerance differs between the low and high sides.
Measurement Category
The measurement category of this instrument’s signal input terminals varies
depending on the modules that are installed.
Use the instrument within the scope of the measurement category that corresponds
to the module specifications. Do not use the instrument outside the scope of the
measurement category that corresponds to the module specifications.
Install or Use the Instrument in Appropriate Locations
• Do not install or use the instrument outdoors or in locations subject to rain or
water.
• Install the instrument so that you can immediately remove the power cord if an
abnormal or dangerous condition occurs.
CAUTION
Operating Environment Limitations
This product is a Class A (for industrial environments) product. Operation of this
product in a residential area may cause radio interference in which case the user
will be required to correct the interference.
Safety Precautions

xii IM 720120-01E
French
AVERTISSEMENT
Utiliser l’instrument aux seules fins pour lesquelles il est prévu
Cet instrument est un appareil de mesure de forme d’onde pour le contrôle et la
mesure des signaux électriques. Ne pas utiliser cet instrument à d’autres fins que
celles de mesure de forme d’onde.
Inspecter l’apparence physique
Ne pas utiliser l’instrument si son intégrité physique semble être compromise.
Vérifier l’alimentation
Avant de brancher le cordon d’alimentation, vérifier que la tension source
correspond à la tension d’alimentation nominale du SL1000 et qu’elle est
compatible avec la tension nominale maximale du cordon d’alimentation.
Utiliser le cordon d’alimentation et la fiche adaptés
Pour éviter les risques de choc électrique ou d’incendie, utilisez le cordon
d’alimentation fourni par YOKOGAWA. La fiche doit être branchée sur une prise
secteur raccordée à la terre. En cas d’utilisation d’une rallonge, celle-ci doit être
impérativement reliée à la terre. Par ailleurs, n’utilisez pas le cordon d’alimentation
fourni pour cet instrument avec un autre appareil.
Brancher la prise de terre
Avant de mettre l’instrument sous tension, penser à brancher la prise de terre pour
éviter tout choc électrique. Le cordon d’alimentation livré avec l’instrument est doté
de trois broches. Brancher le cordon d’alimentation sur une prise de courant à trois
plots et mise à la terre.
Ne pas entraver la mise à la terre de protection
Ne jamais neutraliser le fil de terre interne ou externe, ni débrancher la borne de mise
à la terre. Cela pourrait entraîner un choc électrique ou endommager l’instrument.
Ne pas utiliser lorsque les fonctions de protection sont défectueuses
Avant d’utiliser l’instrument, vérifier que les fonctions de protection, telles que
le raccordement à la terre et le fusible, fonctionnent correctement. En cas de
dysfonctionnement possible, ne pas utiliser l’instrument.
Ne pas utiliser dans un environnement explosif
Ne pas utiliser l’instrument en présence de gaz ou de vapeurs inflammables. Cela
pourrait être extrêmement dangereux.
Ne pas retirer le capot, ni démonter ou modifier l’instrument
Seul le personnel YOKOGAWA qualifié est habilité à retirer le capot et à démonter
ou modifier l’instrument. Certains composants à l’intérieur de l’instrument sont à
haute tension et par conséquent, représentent un danger.
Relier l’instrument à la terre avant de le brancher sur des connexions externes
Toujours relier l’instrument à la terre avant de le brancher aux appareils à mesurer
ou à une commande externe. Avant de toucher un circuit, mettre l’instrument hors
tension et vérifier l’absence de tension.
Précautions à prendre lors de l’utilisation des modules
• Ne pas dépasser les valeurs maximales de tension d’entrée, de tension de
maintien ou de surtension admissible.
• Pour éviter tout risque de choc électrique, toujours relier le SL1000 à la terre.
Safety Precautions

xiii
IM 720120-01E
• Pour éviter tout risque de choc électrique, toujours serrer les vis des modules, à
défaut de quoi les fonctions de protection électrique et de protection mécanique
ne seront pas activées.
• Ne pas laisser les modules branchés à l’instrument dans des environnements
dans lesquels la tension pourrait dépasser la surtension admissible.
• Faire attention de ne pas dépasser la tension d’entrée maximale d’un module
dans les cas suivants.
• Si l’atténuation de la sonde est de 1:1.
• Si le couplage d’entrée du module est paramétré sur le CA.
Une tension CC de même potentiel électrique que l’entrée de sonde s’applique
à l’entrée du module.
Précautions à prendre lors de l’utilisation de sondes
• Pour mesurer la tension élevée avec 720210 (HS100M12), 720211 (HS100M12),
701250 (HS10M12), 720250 (HS10M12) ou 701251 (HS1M16), utiliser une
sonde isolée (700929 ou 701947), des sondes passives 702902 ou des câbles
de sécurité 1:1 (combinaison de 701901 et 701954).
• Lors de l’utilisation du 701255 (NONISO_10M12), veillez à serrer les vis du
module. Le serrage des vis de module active la fonction de protection et celle de
non-isolation. La situation est extrêmement dangereuse lorsque les vis ne sont
pas serrées. Lorsque vous mesurez des hautes tensions supérieures à 42 V,
veillez également à utiliser la sonde passive 701940.
• La partie BNC de la sonde passive 701940 est composée de métal. Utiliser,
par conséquent, la sonde à 42 V ou moins pour les entrées isolées (720210
(HS100M12), 701250 (HS10M12), 701251 (HS1M16)) etc.) pour des raisons de
sécurité. (Ne pas utiliser une tension supérieure à 42 V à la fois en haut et en
bas.) Pour les entrées non-isolées (701255 (NONISO_10M12) etc.), serrer les
vis du module comme décrit précédemment.
• Lorsque vous appliquez de hautes tensions au 701267 (HV (avec RMS)) ou
720268 (HV (AAF, RMS)), utilisez un cordon de mesure (758933 et 701954
conjointement) ou un câble de sécurité 1:1 (701904 et 701954 conjointement)
• La catégorie de mesure de 701267 (HV (avec RMS)) est CAT II - 400 V pour
le bas et CAT II - 700 V pour le haut. Procéder avec soin, car la tolérance de
surtension diffère entre le bas et le haut.
Catégorie de mesure
La catégorie de mesure de ces bornes d’entrée de signal de l’instrument varie en
fonction des modules installés. Utilisez l’instrument dans les limites de la catégorie
de mesure qui correspondent aux spécifications du module. N’utilisez pas
l’instrument en dehors des limites de la catégorie de mesure qui correspondent aux
spécifications du module.
Installer et utiliser l’instrument aux emplacements appropriés
• Ne pas installer, ni utiliser l’instrument à l’extérieur ou dans des lieux exposés à
la pluie ou à l’eau.
• Installer l’instrument de manière à pourvoir immédiatement le débrancher du
secteur en cas de fonctionnement anormal ou dangereux.
ATTENTION
Limitations relatives à l’environnement opérationnel
Ce produit est un produit de classe A (pour environnements industriels). L’utilisation
de ce produit dans un zone résidentielle peut entraîner une interférence radio que
l’utilisateur sera tenu de rectifier.
Safety Precautions

xiv IM 720120-01E
Sales in Each Country or Region
Waste Electrical and Electronic Equipment
Waste Electrical and Electronic Equipment (WEEE), Directive
(This directive is valid only in the EU.)
This product complies with the WEEE directive marking requirement. This marking
indicates that you must not discard this electrical/electronic product in domestic
household waste.
Product Category
With reference to the equipment types in the WEEE directive, this product is
classified as a “Monitoring and control instrumentation” product.
When disposing products in the EU, contact your local Yokogawa Europe B.V.
office. Do not dispose in domestic household waste.
EU Battery Directive
EU Battery Directive
(This directive is valid only in the EU.)
Batteries are included in this product. This marking indicates they shall be sorted
out and collected as ordained in the EU battery directive.
Battery type: Lithium battery
You cannot replace batteries by yourself. When you need to replace batteries,
contact your local Yokogawa Europe B.V. office.
Authorized Representative in the EEA
Yokogawa Europe B.V. is the authorized representative of Yokogawa Meters &
Instruments Corporation for this product in the EEA. To contact Yokogawa Europe
B.V., see the separate list of worldwide contacts, PIM 113-01Z2.

xv
IM 720120-01E
How to Use This Manual
Structure of the Manual
This user’s manual consists of the following sections.
Chapter Title Description
1 Names and Uses of Parts
Describes the names and uses of each part and the screen display.
2 Explanation of Functions
Describes the measurement principles and the functions of the instrument.
Operational details are not given in this chapter. However, reading this
chapter will help you understand the operating procedures given in the
chapters that follow.
3 Before Starting Measurements
Describes handling precautions, how to install the instrument, how to
connect to the power supply, how to turn ON/OFF the power switch, how to
install modules, how to connect probes, and so on.
4 Starting/Stopping Measurements
Describes how to connect the instrument to a PC and how to start/stop
measurements.
5 External I/O Terminals
Describes external trigger input, trigger output, external clock, alarm output,
GO/NO-GO output, etc.
6 Maintenance
Gives troubleshooting advice; explains screen messages and self-test
operation.
7 Specifications
Summarizes the main specifications of the instrument in tables.
Appendix
Provides information about the TCP and UDP port numbers used in the
Ethernet communications; and so on.
Index

xvi IM 720120-01E
Conventions Used in This Manual
Unit
k: Denotes 1000. Example: 100 kS/s (sampling rate)
K: Denotes 1024k. Example: 710 KB (file size)
Bold Characters
Bold characters used in the procedural explanations indicate characters that are marked
on the panel keys or the characters of the soft keys displayed on the screen menu.
Markings
The following markings are used in this manual.
Improper handling or use can lead to injury to the user or damage
to the instrument. This symbol appears on the instrument to indicate
that the user must refer to the users manual for special instructions.
The same symbol appears in the corresponding place in the user’s
manual to identify those instructions. In the manual, the symbol is
used in conjunction with the word “WARNING” or “CAUTION.”
WARNING Calls attention to actions or conditions that could cause serious or
fatal injury to the user, and precautions that can be taken to prevent
such occurrences.
CAUTION Calls attentions to actions or conditions that could cause light injury to
the user or damage to the instrument or user’s data, and precautions
that can be taken to prevent such occurrences.
French
AVERTISSEMENT Attire l’attention sur des gestes ou des conditions
susceptibles de provoquer des blessures graves (voire
mortelles), et sur les précautions de sécurité pouvant
prévenir de tels accidents.
ATTENTION Attire l’attention sur des gestes ou des conditions
susceptibles de provoquer des blessures légères ou
d’endommager l’instrument ou les données de l’utilisateur,
et sur les précautions de sécurité susceptibles de prévenir
de tels accidents.
Note Calls attention to information that is important for proper operation of
the instrument.
Subheadings
On pages that describe the operating procedures in chapters 3 and 4, the following
symbols are used to distinguish the procedures from their explanations.
Procedure Carry out the procedure according to the step numbers. All
procedures are written with inexperienced users in mind;experienced
users may not need to carry out all the steps.
Explanation This section describes the setup items and the limitations regarding
the procedures. It may not give a detailed explanation of the function.
For a detailed explanation of the function, see chapter 2.
How to Use This Manual

xvii
IM 720120-01E
1
2
3
4
5
6
7
App
Index
Contents
List of Manuals...................................................................................................................................i
Checking the Contents of the Package............................................................................................ iii
Safety Precautions...........................................................................................................................ix
Sales in Each Country or Region................................................................................................... xiv
How to Use This Manual.................................................................................................................xv
Chapter 1 Names and Uses of Parts
1.1 Front Panel and Rear Panel............................................................................................. 1-1
1.2 Keys and Indicators.......................................................................................................... 1-3
1.3 Display.............................................................................................................................. 1-4
Chapter 2 Explanation of Functions
2.1 System Conguration and Block Diagram........................................................................ 2-1
2.2 Input Modules................................................................................................................... 2-4
2.3 Operating Conguration ................................................................................................... 2-5
2.4 Independent Operation and Synchronous Operation....................................................... 2-7
Chapter 3 Making Preparations for Measurements
3.1 Handling Precautions ....................................................................................................... 3-1
3.2 Installing the Instrument ................................................................................................... 3-3
3.3 Installing Modules............................................................................................................. 3-6
3.4 Connecting the Power Supply .........................................................................................3-11
3.5 Connecting the Probes................................................................................................... 3-14
3.6 Compensating the Probe (Phase Correction) ................................................................ 3-25
3.7 Connecting Measuring Leads......................................................................................... 3-27
3.8 Connecting Thermocouples............................................................................................ 3-31
3.9 Connecting a Bridge Head ............................................................................................. 3-33
3.10 Connecting Acceleration Sensors .................................................................................. 3-36
3.11 Connecting Sensors to the Frequency Module .............................................................. 3-39
Chapter 4 Starting/Stopping Measurements
4.1 Connecting to a PC .......................................................................................................... 4-1
4.2 Starting/Stopping Measurements ..................................................................................... 4-6
Chapter 5 External I/O Terminals
5.1 Connecting the External Clock Input Terminal (EXT CLK IN)........................................... 5-1
5.2 Connecting the External Trigger Input Terminal (TRIG IN)............................................... 5-2
5.3 Connecting the Trigger Output Terminal (TRIG OUT) ...................................................... 5-3
5.4 Connecting the Alarm Output Terminals (ALARM) ........................................................... 5-5
5.5 Connecting the Remote Input Terminals (REMOTE)........................................................ 5-7
5.6 Connecting the GO/NO-GO Output Terminals ................................................................. 5-9
5.7 Sync I/O connectors (SYNC IN and SYNC OUT) ...........................................................5-11

xviii IM 720120-01E
Contents
Chapter 6 Maintenance
6.1 Troubleshooting................................................................................................................ 6-1
6.2 Codes and Corrective Actions .......................................................................................... 6-2
6.3 Recommended Replacement Parts ................................................................................. 6-4
Chapter 7 Specications
7.1 Input Section .................................................................................................................... 7-1
7.2 Display Section................................................................................................................. 7-1
7.3 Storage............................................................................................................................. 7-1
7.4 External I/O Section ......................................................................................................... 7-2
7.5 Computer Interface........................................................................................................... 7-3
7.6 Synchronous Operation.................................................................................................... 7-3
7.7 General Specications ..................................................................................................... 7-4
7.8 External Dimensions ........................................................................................................ 7-8
Appendix
Appendix 1 TCP and UDP Port Numbers Used in Ethernet Communications...................... App-1
Index