YOKOGAWA UTAdvanced UT35A Manual

UTAdvanced UT35A/UT32A
Digital Indicating Controller
Parameter Ma
p
s and List
s
TI 05P01D31-01EN
©Copyright July. 2011
1st Edition July. 2011
Page 1 / 18

UTAdvanced UT35A/UT32
A
Introduction
Brief Descri
p
tion of Sheets
This sheet provides a brief description of the following sheets entitled "Names and Functions of Display Parts,"
"Operation Parameter Map," "Setup Parameter Map," and "List of Parameters."
"Names and Functions of Display Part
s
"
This sheet describes the names and functions of display parts, function of parameter display level, meaning of
parameter map symbol and numeric value, parameter display transition and setup operation, and display symbol
list.
"Operation Map (PRO)"
This sheet describes the operation parameter map, which can be used as an operation guide.
"Setup Map (PRO)"
This sheet describes the setup parameter map, which can be used as an operation guide.
"List of Parameters (PRO)"
This sheet describes the setting range and initial value of operation parameters and setup parameters. There is a
column for user settings.
Parameters in the sheets are displayed when the parameter display level is set to professional setting mode
(LEVL=PRO). Some parameters are not displayed according to model and suffix codes. For details, refer to the
User's Manual.
Operation Parameters: Parameters for setting the functions necessary for the operation.
Setup Parameters: Parameters for setting the basic functions of the controller.
Notice
The contents of this manual are subject to change without notice as a result of continuing improvements to the
instrument’s performance and functions.
Page 2 / 18

UTAdvanced UT35A/UT32A
Names and Functions of Display Parts
UT35A Dis
p
la
y
Parts
UT32A Dis
p
la
y
Parts
No. in figure
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11) Lit while the ladder program operation is executed.
Ladder operation indicator
(green)
Displays PV. Displays an error code if an error occurs. Displays the scrolling guide in the
Menu Display and Parameter Setting Display when the guide display ON/OFF is set to ON.
Description
Displays a group number (1 to 4, or R) and terminal area (E1 to E4). 1 to 4 represent SP
numbers in the Operation Display. R and E1 to E4 are displayed in the Parameter Setting
Display.
Displays a parameter symbol.
Parameter display level
indicator
(green)
Status indicator
(green and red)
Security indicator (red)
Displays a parameter setpoint and menu symbol.
Displays control output value (OUT) and measured input value (PV).
The data to be displayed can be set by the parameter.
Initial value: deviation, in Heating/cooling control: heatingside control output
Lit when the alarms 1 to 4 occur.
Event displays other than alarms can be set by the parameter.
Lit or blinks when the Up/Down or Left/Right arrow key operation is possible.
Displays the setting conditions of the parameter display level function.
Parameter display level EASY PRO
Easy setting mode Lit Unlit
Standard setting mode Unlit Unlit
Professional setting mode Unlit Lit
Displays the operating conditions and control status.
Display Description
REM Lit when in remote mode (REM).
MAN Lit when in manual mode (MAN). Blinks during auto-tuning.
Lit if a password is set. The setup parameter settings are locked.
Data display (orange)
Bar-graph display
(orange and white)
Event indicator (orange)
Key navigation indicator
(green)
Name
PV display
(white or red)
Group display
(green)
Symbol display (orange)
Page 3 / 18

UT35A Ke
y
Parts
UT32A Ke
y
Parts
No. in figure
(1)
(2)
(3)
(4)
(5)
(6) User function keys
It is the communication interface to the adapter cable when setting and storing parameters
via PC. The LL50A Parameter Setting Software (sold separately) is required.
Used to switch between AUTO and MAN modes.
The setting is switched between AUTO and MAN each time the key is pressed. The user can
assign a function key.
The UT35A has F1, F2, and Fn keys.
The UT32A has only the Fn key. The user can assign a function to the key. The function is
set by the parameter.
UT35A: PARAMETER key
UT32A: PARA key
SET/ENTER key
Up/Down/ Left/Right arrow
keys
Light-loader interface
A/M key
Hold down the key for 3 seconds to move to the Operation Parameter Setting Display.
Hold down the key and the Left arrow key simultaneously for 3 seconds to move to the
Setup Parameter Setting Display.
Press the key in the Parameter Setting Display to return to the Menu Display. Press the key
once to cancel the parameter setting (setpoint is blinking).
SET/ENTER ke
y
Press the key in the Menu Display to move to the Parameter Setting Display of the Menu.
Press the key in the Parameter Setting Display to transfer to the parameter setting mode
(setpoint is blinking), and the parameter can be changed. Press the key during parameter
setting mode to register the setpoint.
Up/Down/Left/Right arrow keys
Press the Left/Right arrow keys in the Menu Display to switch the Displays.
Press the Up/Down/Left/Right arrow keys in the Parameter Setting Display to switch the
Displays.
Press the Up/Down arrow keys during parameter setting mode (setpoint is blinking) to
change a setpoint.
Press the Left/Right arrow keys during parameter setting mode (setpoint is blinking) to
move between digits according to the parameter.
Name
UT35A: DISPLAY key
UT32A: DISP key
Description
Used to switch the Operation Displays.
Press the key in the Operation Display to switch the provided Operation Displays.
Press the key in the Menu Display or Parameter Setting Display to return to the Operation
Display.
Page 4 / 18

Brief Description of Parameter Map
The control prevents unintentional change of the function.
The parameter display level is just a function to hide the display so the set function works.
Changing of parameter display level
The parameters to be displayed can be controlled by changing the setting value for setup parameter LEVL.
Setting value
EASY EAS
Y
Symbol
Corresponding parameters are displayedin all modes.
STD Symbol Symbol
PRO PRO Symbol Symbol Symbol
Corresponding parameters are displayed only in Professional setting mode.
Meaning of Parameter Symbol and Numeric Value
Numeric Value S
y
mbol
↑↑
Group Parameter symbol
Group E1: indicates the parameter in E1-terminal area
E3: indicates the parameter in E3-terminal area
E4: indicates the parameter in E4-terminal area
1 to 4, R: indicate the group numbers
Display may be controlled according to the setting value of the setup parameter and operation status.
Parameter Dis
p
la
y
Transition and Setu
p
O
p
eration
To move to the Operation Parameter Setting Display
To move to the Setup Parameter Setting Display
To move to the Operation Display
<Operation for Setting>
Parameter Display Level
If you cannot remember how to carry out an operation during setting, press the DISPLAY key or DISP key once. This
brings you to the display (Operation Display) that appears at power-on.
Corresponding parameters are displayed only in Standard setting mode and Professional setting mode.
Parameter display level indicators "EASY" and "PRO" are unlit in Standard setting mode.
The parameter display level is a function to control the parameters to be displayed. The factory setting is
LEVL=STD.
To select the parameter setting displayed as the initial value, press the Down arrow key to move to the next parameter.
To change and set the parameter setting, press the SET/ENTER key to start the setpoint blinking. The blinking state allows
you to make changes (setting mode). Use the Up/Down/Left/Right arrow keys to change the setpoint. Press the
SET/ENTER key to register the setting.
＋Press the key
for 3 seconds.
/
Press the key
for 3 seconds.
/
Page 5 / 18

The followin
g
o
p
eratin
g
p
rocedure describes an exam
p
le of settin
g
alarm set
p
oint
(
A1
)
. <In case of UT35A
>
1. Hold down the PARAMETER ke
y
for 3 seconds in the O
p
eration Dis
p
la
y
to call u
p
the
[
MODE
]
Menu Dis
p
la
y
.
2. Press the Ri
g
ht arrow ke
y
to dis
p
la
y
the
[
SP
]
Menu Dis
p
la
y.
3. Press the SET
/
ENTER ke
y
to dis
p
la
y
the
[
SP
]
Parameter Settin
g
Dis
p
la
y.
4. Press the Down arrow ke
y
to dis
p
la
y
the
[
A1
]
Parameter Settin
g
Dis
p
la
y
5. Press the SET
/
ENTER ke
y
to blink the set
p
oint.
6. Press the U
p
or Down arrow ke
y
to chan
g
e the set
p
oint
.
7. Press the SET
/
ENTER ke
y
to re
g
ister the set
p
oint
(
the set
p
oint sto
p
s blinkin
g).
8. Press the PARAMETER ke
y
once to return to the Menu Dis
p
la
y
.
Press the DISPLAY ke
y
once to return to the O
p
eration Dis
p
la
y.
This com
p
letes the settin
g
p
rocedure
.
How to Cancel Parameter Settin
g
To cancel
p
arameter settin
g
when a
p
arameter is bein
g
set
(
set
p
oint is blinkin
g),
p
ress the PARAMETER ke
y
once
(Change the setpoint using the Up/Down arrow keys to increase and decrease the value and the Left/Right
arrow keys to move between digits.)
Page 6 / 18

How to Set Parameter Set
p
oin
t
Numeric Value Settin
g
Selection Data Settin
g
Time
(
minute.second
)
Settin
g
Page 7 / 18

List of Display Symbols
Figure (common to all display area)
PV display (14 segments): Alphabet
Symbol display and Data display (11 segments): Alphabet
Group display (7 segments): Alphabet
PV display (14 segments): Symbol
The following shows the parameter symbols, menu symbols, alphanumeric of guide, and symbols which are
displayed on the UT35A/UT32A.
Page 8 / 18

UTAdvanced UT35A/UT32A
Operation Parameter Map * Some parameters are not displayed according to the model and suffix codes or the setting of CNT parameter. For details, refer to the User's Manual.
Operation
Mode SELECT Parameter
SP and
Alarm
Setpoint
Setting
SP-related
Setting
Alarm
Function
Setting
PV-related
Setting PID Setting Tuning Zone Control P Parameter
(END) MODE CS SP SPS ALRM PVS PID TUNE ZONE PPAR END (MODE)
S.R CS10 1SP 4SP RT AL1 BS 1P4PRP SC RP1 P01
R.L CS11 1SUB 4SUB RBS AL2 FL 1I4IRI AT.TY RP2 P02
AT CS12 1PIDN 4PIDN UPR AL3 END 1D4DRDAT.OH RP3 P03
SPNO. CS13 1A1 ······ 4A1 DNR AL4 1OH 4OH ROH AT.OL RHY P04
PID CS14 1A2 4A2 TMU VT1 1OL 4OL ROL AT.BS RDV P05
END CS15 1A3 4A3 SPT VT2 1MR 4MR RMR AR END P06
CS16 1A4 4A4 PVT VT3 1HYS 4HYS RHYS OPR P07
CS17 END END END VT4 1SU.HY 4SU.HY RSU.HY OLMT P08
CS18 HY1 1HY.UP 4HY.UP RHY.UP MPON P09
CS19 HY2 1HY.LO 4HY.LO RHY.LO MPO1 P10
END HY3 1DR ······ 4DR ··· RDR MPO2 END
HY4 1SU.DR 4SU.DR RSU.DR MPO3
DYN1 1Pc 4Pc RPc MPO4
DYN2 1Ic 4Ic RIc MPO5
DYN3 1Dc 4Dc RDc END
DYN4 1OHc 4OHc ROHc
S
y
mbol
Corresponding parameters are displayedin all modes. DYF1 1OLc 4OLc ROLc
DYF2 1HYSc 4HYSc RHYSc
DYF3 1DB 4DB RDB
S
y
mbol DYF4 1PO 4PO RPO
AMD 1SU.PO 4SU.PO RSU.PO
END 1POc 4POc RPOc
S
y
mbol Corresponding parameters are displayed only in Professional setting mode. END END END
Numeric Value S
y
mbol
↑↑
Group Parameter symbol
To move to the Setup Parameter Setting Display
To move to the Operation Parameter Setting Display
Operation
Display
Display may be controlled according to the setting value of the setup parameter and
operation status.
Corresponding parameters are displayed only in Standard setting mode and Professional setting
mode. Parameter display level indicators "EASY" and "PRO" are unlit in Standard setting mode.
/
CS menu is displayed when the SELECT
p
arameter has been re
g
istered.
Parameters for setting
the functions necessary
f
o
r
t
h
e
ope
r
at
i
o
n.
Press the key
for 3 seconds.
/
SET/ENTER key
If you cannot remember how to carry out an operation during setting,
press the DISPLAY key or DISP key once. This brings you to the display
(Operation Display) that appears at power-on.
＋Press the key
for 3 seconds.
/
Press the key
for 3 seconds.
/
Page 9 / 18

UTAdvanced UT35A/UT32A
Setup Parameter Map * Some parameters are not displayed according to the model and suffix codes or the setting of CNT parameter. For details, refer to the User's Manual.
PASS
Control
Function
Setting
PV Input
Setting
Input
Range/SP
Limiter
Setting
Output
Setting
Heater
Break Alarm
Setting
RS-485
Communicat
ion Setting
(E1 terminal
area
)
RS-485
Communicat
ion Setting
(E3 terminal
area
)
Ethernet
Communicat
ion Setting
PROFIBUS-
DP
Communicat
ion Setting
DeviceNet
Communicat
ion Setting
CC-Link
Communicat
ion Setting
Key Action
Setting
Display
Function
Setting
SELECT
Display
Setting
(END) CTL PV MPV OUT HBA E1 R485 E3 R485 E3 ETHR E3 PROF E3 DNET E3 CC-L KEY DISP CSEL
CNT IN P.UNI OT HB1.S E1 PSL E3 PSL E3 HSR E3 BR E3 BR E3 BR F1 PCMD CS1
ALG UNIT P.DP CT HB2.S E1 BPS E3 BPS E3 BPS E3 ADR E3 ADR E3 ADR F2 PCH CS2
SPGR. RH P.RH CTc HB1 E1 PRI E3 PRI E3 PRI E3 BPS E3 BPS E3 BPS Fn PCL CS3
ALNO. RL P.RL V.AT HB2 E1 STP E3 STP E3 IP1 E3 FILE E3 FILE E3 FILE A/M BAR1 CS4
ZON SDP SPH V.RS CT1.T E1 DLN E3 DLN E3 IP2 E3 SCAN E3 SCAN E3 SCAN END BDV CS5
PIDG. SH SPL V.L CT2.T E1 ADR E3 ADR E3 IP3 END END END EV1 CS10
END SL END V.H HDN1 E1 RP.T E3 RP.T E3 IP4 EV2 CS11
BSL TR.T HDN2 END END E3 SM1 EV3 CS12
RJC V.MOD HDF1 E3 SM2 EV4 CS13
ERJC RTS HDF2 E3 SM3 PV.D CS14
A.BS RTH HB1.D E3 SM4 SP.D CS15
A.FL RTL HB2.D E3 DG1 STS.D CS16
END O1RS END E3 DG2 SPD CS17
O1RH E3 DG3 GUID CS18
O1RL E3 DG4 HOME CS19
OU.A E3 PRT ECO END
RET.A E3 IPAR BRI
END E3 1.IP1 B.PVW
E3 1.IP2 B.PVR
E3 1.IP3 B.SP
Symbol
Corresponding parameters are displayedin all modes. E3 1.IP4 B.BAR
E3 2.IP1 B.STS
E3 2.IP2 D.CYC
Symbol E3 2.IP3 OP.JP
E3 2.IP4 MLSD
E3 ESW END
Symbol Corresponding parameters are displayed only in Professional setting mode. END
Numeric Value Symbol
↑↑
Group Parameter symbol
Key Lock
Setting Menu Lock Setting DI Function Registration DI Function Numbering
DI1-DI2
Contact
Type
Setting
DI Setting
(E1 terminal
area)
DI Setting
(E4 terminal
area)
AL1-AL3
Function
Registration
DO Setting
(E1 terminal
area)
DO Setting
(E4 terminal
area) I/O Display System
Setting Initialization Error and
Version
Confirmation
Parameter
Display
Level
KLOC MLOC DI.SL DI.NU DI.D E1 DI.D E4 DI.D ALM E1 DO E4 DO I/O SYS INIT VER LVL END (CTL)
U.SP CTL A/M SP.B0 DI1.D E1 DI1.D E4 DI1.D AL1.S E1 DO1.S E4 DO1.S KEY R.MD U.DEF PA.ER LEVL
U.OUT PV R/L SP.B1 DI2.D E1 DI2.D E4 DI2.D AL2.S E1 DO2.S E4 DO2.S X000 R.TM F.DEF OP.ER
U.HCO MPV S/R SP.B2 END E1 DI3.D E4 DI3.D AL3.S E1 DO3.S E4 DO3.S E1 X100 EPO END AD1.E
U.VP OUT AUTO PN.B0 E1 DI4.D E4 DI4.D OR.S E1 DO4.S E4 DO4.S E4 X400 C.GRN AD2.E
U.MV HBA MAN PN.B1 E1 DI5.D E4 DI5.D OR2.S E1 DO5.S E4 DO5.S Y000 FREQ PV1.E
U.PID E1 R485 REM PN.B2 END END AL1.D E1 DO1.D E4 DO1.D E1 Y100 QSM LA.ER
U.HC E3 R485 LCL MP.B0 AL2.D E1 DO2.D E4 DO2.D E4 Y400 LANG MCU
U.PV E3 ETHR AT MP.B1 AL3.D E1 DO3.D E4 DO3.D END PASS DCU
COM.W E3 PROF LAT MP.B2 OR.D E1 DO4.D E4 DO4.D SMEC E1 ECU1
DATA E3 DNET LCD SP.BC OR2.D E1 DO5.D E4 DO5.D END E3 ECU3
A/M E3 CC-L PVRW PN.BC END END END E4 ECU4
END KEY MG1 MP.BC PARA
DISP MG2 END H.VER
CSEL MG3 SER1
KLOC MG4 SER2
DI.SL END E3 MAC1
DI.NU E3 MAC2
DI.D E3 MAC3
E1 DI.D END
E4 DI.D
MODE ALM
CS E1 DO
SP E4 DO
SPS I/O
ALRM SYS
PVS INIT
PID VER
TUNE LVL
ZONE
PPAR
END
Corresponding parameters are displayed only in Standard setting mode and Professional setting
mode. Parameter display level indicators "EASY" and "PRO" are unlit in Standard setting mode.
Operation
Display
/
Displayed when a password has
Parameters for setting
the basic functions of the
controller
＋Press the key
f
o
r
3
seco
n
ds
.
/
SET
/
ENTER ke
y
If you cannot remember how to carry out an operation during
setting, press the DISPLAY key or DIPS key once. This brings you to
the dis
p
la
y
(
O
p
eration Dis
p
la
y)
that a
pp
ears at
p
ower-on.
SET
/
ENTER ke
y
Page 10 / 18