York AC018X1222 Quick start guide

SPLIT-SYSTEM
AIR CONDITIONERS
12 SEER
MODELS:
AC018X12* THRU 060
(1.5 THRU 5 NOMINAL TONS, 1 PH)
Due to continuous product improvement, specifications
are subject to change without notice.
Visit us on the web at www.york.com for the most
up-to-date technical information.
Additional rating information can be found at
www.ariprimenet.org.
LISTED
CERTIFICATION APPLIES ONLY
WHEN THE COMPLETE
SYSTEM IS LISTED
WITH ARI.
ISO 9001
Certified Quality
Management System
R
N
E
M
P
I
U
Q
E
T
Y
R
A
T
I
N
U
0
1
2
ARI
R
A
D
N
A
T
S
D
I
S
N
O
T
C
E
S
F
O
C
C
I
F
I
T
R
E
N
O
I
T
A
H
T
I
W
C
G
N
I
Y
L
P
M
O
S
A
I
R
A
O
T
D
E
I
F
I
T
R
E
C
R
E
R
U
T
C
A
F
U
N
A
M
C
-
G
N
I
N
O
I
T
I
D
N
O
R
I
A
036-21106-005 Rev. B (0505)
FOR DISTRIBUTION USE ONLY - NOT TO BE USED AT POINT OF RETAIL SALE
TECHNICAL
GUIDE
TECHNICAL
GUIDE
DESCRIPTION
The 12 SEER Series condensing unit is the outdoor
part of a versatile system of air conditioning. It is
designed to be custom-matched with one of UPG’s
complete line of evaporator sections, each designed to
serve a specific function. Matching Air Handlers are
available for upflow, downflow or horizontal applica-
tions to provide a complete system. Electric Heaters
are available if required. Add-On coils are available for
use with upflow, downflow or horizontal furnaces and
air handlers.
WARRANTY
5-year limited parts warranty.
10-year limited compressor warranty.
FEATURES
•QUALITY CONDENSER COILS - The coil is constructed
of enhanced copper tube and aluminum fins.
•COIL PROTECTION - Coils are protected from damage by
a polymer mesh applied between the coil face, and a PVC
coated steel coil guard.
•PROTECTED COMPRESSOR - The compressor is inter-
nally protected against high pressure and temperature.
This is accomplished by the simultaneous operation of
high pressure relief valve and a temperature sensor which
protects the compressor if undesirable operating condi-
tions occur. A liquid line filter-drier further protects the
compressor.
•DURABLE FINISH - The cabinet is made of pre-painted
steel. The pre-treated galvanized steel provides a better
paint to steel bond, which resists corrosion and rust creep.
Special primer formulas and matted textured champagne
finish insure less fading when exposed to sunlight.
•LOWER INSTALLED COST - Installation time and costs
are reduced by easy power and control wiring connec-
tions. Discharge line heat exchanger knockouts are pro-
vided, if required. Available in sweat connect models only.
The unit contains enough refrigerant for matching indoor
coils and 15 feet of interconnecting piping. The small base
dimension means less space is required on the ground or
roof.
•TOP DISCHARGE - The warm air from the top mounted
fan is blown up away from the structure and any landscap-
ing. This allows compact location on multi-unit applica-
tions.
•LOW OPERATING SOUND LEVEL - The upward air flow
carries the normal operating noise up away from the living
area. The rigid top panel effectively isolates any motor
sound. Isolator mounted compressor and the rippled fins
of the condenser coil muffle the normal fan motor and
compressor operating sounds.
•LOW MAINTENANCE - Long life permanently lubricated
motor-bearings need no annual servicing.
•EASY SERVICE ACCESS - Fully exposed refrigerant con-
nections, a single panel covering the electrical controls
and the molex plug in the control box connecting the con-
denser fan, make for easy servicing of the unit.
•SECURED SERVICE VALVES - Secured re-usable ser-
vice valves are provided on both the liquid and vapor
sweat connections for ease of evacuating and charging.
•U.L. and C.U.L. listed - approved for outdoor application.
Certified in accordance with the Unitary Small Equipment cer-
tification program, which is based on ARI Standard 210/240.

036-21106-005 Rev. B (0505)
2Unitary Products Group
Physical and Electrical Data
MODEL AC018X1222 AC024X1222 AC030X1222 AC036X1222 AC042X1221 AC048X1222 AC060X1224
Unit Supply Voltage 208/230 – 1 – 60
Normal Voltage Range 1187 to 252
Minimum Circuit Ampacity 10.1 14.1 16.5 19.7 26.2 28.5 37.5
Max. Overcurrent Device Amps 215 25 25 30 45 50 60
Compressor Type3Recip Inertia Recip Recip ScrollBRecip ScrollB
Compressor Amps Rated Load 7.7 10.9 12.8 14.7 19.9 21.8 28.8
Locked Rotor 48 60 68 82 115 105 145
Crankcase Heater No No No Yes No No No
Fan Motor Amps Rated Load 0.5 0.5 0.5 1.3 1.3 1.3 1.5
Fan Diameter Inches 18 18 22 22 22 22 22
Fan Motor Rated HP 1/12 1/12 1/15 1/4 1/4 1/4 1/4 Nominal RPM 1,100 1,100 850 850 850 850 850
Nominal CFM 2,000 2,000 2,300 3,300 3,300 3,300 3,450
Coil Face Area Sq. Ft. 12.58 12.58 15.72 15.72 17.03 19.65 23.58 Rows Deep 1 1 1 1 1 1 1
Fin / Inches 18 18 18 18 18 18 22
Liquid Line OD 3/8 3/8 3/8 3/8 3/8 3/8 3/8
Vapor Line OD 3/4 3/4 3/4 3/4 7/8 7/8 1-1/8
Unit Charge (Lbs. - Oz.) 44 - 9 4 - 7 5 - 8 5 - 3 6 - 13 7 - 7 8 - 15
Charge Per Foot, Oz. 0.68 0.68 0.68 0.68 0.70 0.70 0.76
Operating Weight Lbs. 144 146 156 161 157 190 198
1 Rated in accordance with ARI Standard 110, utilization range “A”.
2 Dual element fuses or HACR circuit breaker.
3 All scrolls listed with a superscript “B” are Bristol scrolls. All scrolls listed with a superscript “C” are Copeland scrolls.
4 The Unit Charge is correct for the outdoor unit, matched indoor coil and 15 feet of refrigerant tubing. For tubing lengths other than 15 feet, add or sub-
tract the amount of refrigerant, using the difference in length multiplied by the per foot value.
All dimensions are in inches. They are subject to change without
notice. Certified dimensions will be provided upon request.
* Expander fitting required for 1-1/8” line set.
A
B
C
DIMENSIONS - 1 Phase
UNIT
MODEL DIMENSIONS (INCHES) REFRIGERANT CONNECTION LINE SIZE
A11
1 Including Fan Guard.
B C Liquid Vapor
018 25 35 23
3/8””
3/4”
024 25 35 23
030 27 37 27
036 27 37 27
042 29 37 27 7/8”
048 33 37 27
060 39 37 27 7/8”*

036-21106-005 Rev. B (0505)
Unitary Products Group 3
Additional R-22 Charge / Orifice Size for Various Matched Systems - 1 Phase
Outdoor Unit AC018X1222 AC024X1222 AC030X1222 AC036X1222 AC042X1221 AC048X1222 AC060X1224
Unit Orifice (s) 153 59 63 73 78 87 –
Factory R-22 Charge, lbs-oz. 4 - 9 4 - 7 5 - 8 5 - 3 6 - 13 7 - 7 8 - 15
Indoor Coil Coil Orifice4Orifice or TXV Kit 2- Additional Charge, Oz.3
G2FD024(S,H)14,17(T) 61 53 + 3 59 + 3 – – – – –
701 + 3 701 + 3 – – – – –
G2FD030(S,H)17(T) 65 53 + 6 59 + 6 63 + 4 – – – –
701 + 6 701 + 6 701 + 4 – – – –
G2FD035(S,H)14(T) 65 53 + 6 59 + 6 63 + 4 73 + 0 – – –
701 + 6 701 + 6 701 + 4 702 + 0 – – –
G2FD036(S,H)17(T) 75 – 59 + 10 63 + 8 73 + 6 – – –
– 701 + 10 701 + 8 702 + 6 – – –
G2FD036(S,H)21(T) 75 – – 63 + 11 73 + 8 – – –
– – 701 + 11 702 + 8 – – –
G2FD042(S,H)21(T) 78 – – 63 + 14 73 + 12 78 + 0 – –
– – 701 + 14 702 + 12 702 + 0 – –
G2FD046(S,H)17(T) 78 – – 63 + 16 73 + 12 78 + 0 87 + 0 –
– – 701 + 16 702 + 12 702 + 0 703 + 0 –
G2FD048(S,H)21,24(T) 84 – – – 73 + 16 78 + 10 87 + 11 –
– – – 702 + 16 702 + 10 703 + 11 –
G2FD060(S,H)24(T) 90 –––––87+15–
– – – – – 703 + 15 703 + 5
G2FD061H24(T) 90 –––––87+19–
– – – – – 703 + 19 703 + 11
G1HD024 59 53 + 5 59 + 4 – – – – –
701 + 5 701 + 4 – – – – –
G1HD036 69 – 59 + 13 63 + 11 73 + 7 – – –
– 701 + 13 701 + 11 702 + 7 – – –
G1HD048 81 – – – 73 + 13 78 + 3 87 + 4 –
– – – 702 + 13 702 + 3 703 + 4 –
G1HD060 93 –––––87+12
– – – – – 703 + 12
G1FA/G1UA024S14,17(T) 59 53 + 0 59 + 0 – – – –
701 + 0 701 + 0 – – – 703 + 5
G1FA/G1UA030S14(T) 65 – 59 + 3 63 + 0 – – – –
– 701 + 3 701 + 0 – – – –
G1FA/G1UA036S14(T) 73 – 59 + 8 63 + 6 73 + 3 – – –
– 701 + 8 701 + 6 702 + 3 – – –
G1FA/G1UA036S17,21(T) 73 – 59 + 6 63 + 4 73 + 0 – – –
– 701 + 6 701 + 4 702 + 0 – – –
G1FA/G1UA048S17(T) 84 – – 63 + 16 73 + 13 78 + 0 87 + 0 –
– – 701 + 16 702 + 13 702 + 0 703 + 0 703 + 0
G1FA/G1UA048S21(T) 84 – – 63 + 18 73 + 9 78 + 7 87 + 8 –
– – 701 + 18 702 + 9 702 + 7 703 + 8 –
G1FA/G1UA060S21,24(T) 90 – – – – 78 + 16 87 + 15 –
– – – – 702 + 16 703 + 15 –
G1HA024H14 61 053 + 03 059 + 03 – – – – –
G1HA024H14(T) TXV 701 + 03 + 03 – – – – –
G1HA036H14 75 – 59 + 12 63 + 11 73 + 08 – – –
G1HA036H14(T) TXV 702 – – + 11 + 08 – – –
G1HA036H17 78 – – 63 + 14 73 + 12 – – –
G1HA036H17(T) TXV 702 – – + 14 + 12 – – –
G1HA048H21 84 – – – 73 + 09 78 + 07 87 + 08 –
G1HA048H21(T) TXV 703 – – – + 09 + 07 + 08 –
G1HA060H24 90 – – – – – 87 + 15 –
G1HA060H24(T) TXV 703 – – – – – + 15 703 + 5
G1NA030S17K 63 53 + 6 59 + 6 63 + 4 – – – –
701 + 6 701 + 6 701 + 4 – – – –
G1NA030S21M 78 53 + 6 59 + 6 63 + 4 – – – –
701 + 6 701 + 6 701 + 4 – – – –

036-21106-005 Rev. B (0505)
4Unitary Products Group
FOOTNOTES:
1. These orifices are factory mounted in the flow control device of each indoor coil and must be removed for TXV installation.
2. A TXV kit must be used with these coils to obtain system performance. (701,702,703 indicates 1TV07 ...series).
3. Systems matched with furnaces or air handlers not equipped with blower-off delays, may require blower Time Delay Kit #6918A5011.
PROCEDURES:
1. Unit factory charge listed on the unit nameplate includes refrigerant for the condenser, the smallest evaporator and for 15 feet of
interconnecting line tubing.
2. Verify the orifice size and additional charge required for specific evaporator coil in the system using the above table.
3. Additional charge for the amount of interconnecting line tubing greater than 15 feet at the rate specified in the table above.
4. Permanently mark the unit nameplate with the total system charge. Total System Charge = Base Charge (as shipped) + adder for
evaporator + adder for line set.
5. If the orifice in the evaporator was changed, verify the evaporator nameplate has been marked with the correct orifice size.
G1NA036S17L 63 – – 63 + 15 73 + 12 – – –
– – 701 + 15 702 + 12 – – –
G1NA048S21D 78 – – – 73 + 12 78 + 0 87 + 0 –
– – – 702 + 12 702 + 0 703 + 0 –
G1NA048S24P 63 – – – 73 + 13 78 + 2 87 + 1 –
– – – 702 + 13 702 + 2 703 + 1 –
G1NA060S24T 78 –––––––
––––––703+0
G1NF024SOF 63 –––––––
–––––––
G1NF036SOF 67 – 59 + 12 63 + 0 73 + 7 – – –
– 701 + 12 701 + 0 702 + 7 – – –
G1NF048SOF 78 – – – – 78 + 21 87 + 6 –
– – – – 702 + 21 703 + 6 –
G1NF060SOF 87 –––––87+18–
– – – – – 703 + 18 –
F2RP024N06(T) 61 53 + 4 59 + 4 – – – – –
701 + 4 701 + 4 – – – – –
F2RP030N06(T) 65 – 59 + 6 63 + 4 – – – –
– 701 + 6 701 + 4 – – – –
F2RP036N06(T) 75 – – 63 + 4 73 + 8 – – –
– – 701 + 4 702 + 8 – – –
F2RP042N06(T) 78 – – – 73 + 13 78 + 0 – –
– – – 702 + 13 702 + 0 – –
F2FP048N06(T) 84 – – – 73 + 16 78 + 10 87 + 11 –
– – – 702 + 16 702 + 10 703 + 11 –
F2FP060N06(T) 90 –––––87+15–
– – – – – 703 + 15 7035+ 5
F2FV060N06(T) 90 –––––87+15–
– – – – – 703 + 15 703 + 5
Additional R-22 Charge / Orifice Size for Various Matched Systems - 1 Phase (Continued)
Outdoor Unit AC018X1222 AC024X1222 AC030X1222 AC036X1222 AC042X1221 AC048X1222 AC060X1224
Unit Orifice (s) 153 59 63 73 78 87 –
Factory R-22 Charge, lbs-oz. 4 - 9 4 - 7 5 - 8 5 - 3 6 - 13 7 - 7 8 - 15
Indoor Coil Coil Orifice4Orifice or TXV Kit 2- Additional Charge, Oz.3

036-21106-005 Rev. B (0505)
Unitary Products Group 5
- = Not applicable.
COOLING CAPACITY - With Air Handler Coils
UNIT MODEL AIR HANDLER COIL1
MODEL
COOLING
MODEL ELECTRIC2
HEAT KW WRATED
CFM TOTAL CAPACITY SENSIBLE CAPACITY SEER
W/O TXV SEER
WITH TXV3EER
1 PH 12 SEER AC WITH N-AH / G2FD
AC018X1222 N1AHB0806 2,5,8,10 17 G2FD024(S,H)17 600 19.6 13.2 12.50 12.50 11.60
AC024X1222 N1AHB0806 2,5,8,10 17 G2FD024(S,H)17 750 23.6 16.9 12.00 12.00 11.00
N1AHB0806 2,5,8,10 17 G2FD030(S,H)17 750 24.0 17.3 12.00 12.00 11.10
AC030X1222 N1AHB1206 2,5,8,10 17 G2FD030(S,H)17 1000 30.0 21.3 12.00 12.00 11.00
N1AHB1206 2,5,8,10 17 G2FD036(S,H)17 1000 30.6 21.8 12.25 12.25 11.20
AC036X1222 N1AHB1206 5,8,10,15,19 17 G2FD036(S,H)17 1200 33.8 23.6 11.50 11.50 10.70
N1AHB1206 5,8,10,15,19 17 G2FD046(S,H)17 1200 35.0 24.4 12.00 12.00 10.90
AC042X1221 N1AHC1606 5,8,10,15,20 21 G2FD042(S,H)21 1400 41.0 29.3 12.00 – 10.50
N1AHC1606 5,8,10,15,20 21 G2FD048(S,H)21 1400 42.5 30.6 12.00 – 10.75
AC048X1222 N1AHC1606 5,8,10,15,20 21 G2FD048(S,H)21 1575 46.5 36.0 12.20 12.20 10.90
N1AHD2006 8,10,15,20,25,30 24 G2FD060(S,H)24 1575 48.0 36.4 12.50 12.50 11.10
N1AHD2006 8,10,15,20,25,30 24 G2FD061H24 1575 48.5 34.5 12.50 12.50 11.20
AC060X1223 N1AHD2006 8,10,15,20,25,30 24 G2FD060(S,H)24(T) 1800 56.5 43.4 – 12.00 10.10
N1AHD2006 8,10,15,20,25,30 24 G2FD061H24 1800 56.5 43.8 – 12.00 10.15
1 PH 12 SEER AC / F2RP / RC / FC4,5
AC018X1222 F2RC/F2FC024 5,8,10 18 – 600 20.0 13.2 12.50 12.50 11.70
F2RP/F2FP024 5,8,10 18 – 600 20.0 13.2 12.50 12.50 11.70
AC024X1222
F2RC/F2FC024 5,8,10 18 – 750 23.4 17.5 11.50 11.50 10.85
F2RC/F2FC030 5,8,10,15 18 – 750 23.4 17.5 11.50 11.50 10.85
F2RP/F2FP024 5,8,10 18 – 750 23.6 17.5 12.00 12.00 10.90
F2RP/F2FP030 5,8,10,15 18 – 750 24.0 17.9 12.00 12.00 11.10
AC030X1222
F2RC/F2FC030 5,8,10,15 18 – 1000 29.8 21.5 12.00 12.00 11.00
F2RC/F2FC036 5,8,10,15 21 – 1000 31.0 22.4 12.25 12.25 11.30
F2RP/F2FP030 5,8,10,15 18 – 1000 30.2 22.9 12.00 12.00 11.15
F2RP/F2FP036 5,8,10,15,19 21 – 1000 30.2 23.5 12.00 12.00 11.15
AC036X1222
F2RC/F2FC036 5,8,10,15 21 – 1200 34.6 26.2 12.00 12.00 10.85
F2RP/F2FP036 5,8,10,15,19 21 – 1200 34.6 26.2 12.00 12.00 10.85
F2RP/F2FP042 5,8,10,15 21 – 1200 34.8 26.3 11.60 11.60 10.70
F2FP048 5,8,10,15,20,25 24 – 1200 35.4 26.7 12.00 12.00 10.90
AC042X1221 F2RP/F2FP042 5,8,10,15 21 – 1400 40.5 28.9 11.80 – 10.35
F2FP048 5,8,10,15,20,25 24 – 1400 42.5 30.5 12.00 – 10.55
AC048X1222 F2FP048 5,8,10,15,20,25 24 – 1565 46.5 34.9 11.40 11.40 10.75
F2FP060 5,8,10,15,20,25 24 – 1575 48.0 35.9 11.50 11.50 10.70
AC060X1223 F2FP060 5,8,10,15,20,25 24 – 1800 56.0 42.0 – 12.00 10.00
Rated in accordance with DOE test procedures (Federal Register 12-27-79 and 3-18-88) and ARI Standards 210.
Cooling MBH based on 80°F entering air temperature, 50% RH, and rated air flow.
EER (Energy Efficiency Ratio) is the total cooling output in BTU’s at a 95°F outdoor ambient divided by the total electric power in watt-hours at those conditions.
SEER (Seasonal Energy Efficiency Ratio) is the total cooling output in BTU’s during a normal annual usage period for cooling divided by the total electric power input in
watt-hours during the same period.
1 G2FD coils available with a factory installed horizontal drain pan. See price pages for specific model number.
2 Single phase units require single phase 2HK heaters. Three phase units require three phase 2HK heaters.
3 TXV = Thermal Expansion Valve kit required. Use 1TV700 series kit.
4 To meet R=4.2 insulation requirements, substitute F2FP for F2RP, and F2FC for F2RC. models. All ratings remain the same.
5 FG8, FG9, and FL8 furnaces and F2RP / F2RC air handlers have B.O.D (Blower on Delay) standard.

036-21106-005 Rev. B (0505)
6Unitary Products Group
COOLING CAPACITY - Upflow, Downflow & Horizontal Furnaces and Coils
UNIT MODEL FURNACE** COIL
MODEL
COOLING
CFM RANGE
(MIN.-MAX.) WRATED
CFM NET MBH SEER W/O TXV SEER + TXV1EER
TOTAL SENS.
AC018X1222 525
675
14,17 G1FA024S14,17 600 19.2 13.0 12.00* 12.00 11.35
14 G1HA024H14 600 19.2 13.6 12.00* –11.50
14 G1HA024H14T 600 19.2 13.6 –12.00* 11.60
- G1HD024 600 20.0 13.5 12.50* 12.50 11.70
17 G1NA030S17K 600 20.0 13.5 12.75* 12.75 11.75
21 G1NA030S21M 600 20.0 13.5 12.50* 12.50 11.75
14,17 G1UA024S14,17 600 19.2 13.0 12.00* 12.00 11.35
14,17 G2FD024(S,H)14,17 600 19.6 13.2 12.50* 12.50 11.60
17 G2FD030(S,H)17 600 20.0 13.5 12.60* 12.60 11.75
14 G2FD035(S,H)14 600 20.0 13.5 12.60* 12.60 11.75
AC024X1222 650
850
14,17 G1FA024S14,17 750 23.0 16.4 11.80* 11.80 10.70
14 G1FA030S14 750 23.6 16.9 12.00* 12.00 11.00
14 G1FA036S14 750 24.2 17.6 12.00* 12.00 11.25
17,21 G1FA036S17,21 750 24.0 17.3 12.00* 12.00 11.10
14 G1HA024H14 750 19.2 13.6 12.00* –10.90
14 G1HA024H14T 800 23.5 16.7 –12.00* 10.90
14 G1HA036H14 800 24.6 17.5 12.00 –11.35
- G1HD024 750 24.0 17.2 12.00* 12.00 11.05
- G1HD036 750 24.6 17.6 12.10* 12.10 11.35
17 G1NA030S17K 750 24.0 17.2 12.00* 12.00 11.15
21 G1NA030S21M 750 24.0 17.2 12.00* 12.00 11.15
14,17 G1UA024S14,17 750 23.0 16.4 11.80* 11.80 10.70
14 G1UA030S14 750 23.6 16.9 12.00* 12.00 11.00
14 G1UA036S14 750 24.2 17.6 12.00* 12.00 11.25
17,21 G1UA036S17,21 750 24.0 17.3 12.00* 12.00 11.10
14,17 G2FD024(S,H)14,17 750 23.6 16.9 12.00* 12.00 11.00
17 G2FD030(S,H)17 750 24.0 17.3 12.00* 12.00 11.10
14 G2FD035(S,H)14 750 24.0 17.3 12.10* 12.10 11.10
17 G2FD036(S,H)17 750 24.6 17.8 12.15* 12.15 11.35
AC030X1222 875
1125
14 G1FA030S14 1000 29.2 20.7 11.85* 11.85 10.80
14 G1FA036S14 1000 30.4 21.6 12.00* 12.00 11.10
17,21 G1FA036S17,21 1000 30.0 21.3 12.00* 12.00 11.00
17 G1FA048S17 1000 31.2 22.3 12.50* 12.50 11.45
21 G1FA048S21 1000 31.2 22.3 12.50* 12.50 11.35
14 G1HA036H14 1000 30.3 21.5 12.00* –11.25
14 G1HA036H14 1000 30.2 21.4 –12.00* 11.25
17 G1HA036H17 1000 30.4 21.9 12.00* –11.35
17 G1HA036H17T 1000 30.5 22.0 –12.00* 11.35
- G1HD036 1000 30.8 21.9 12.75* 12.75 11.25
17 G1NA030S17K 1000 30.2 21.4 12.00* 12.00 11.05
21 G1NA030S21M 1000 30.2 21.4 12.00* 12.00 11.05
17 G1NA036S17L 1000 31.4 22.3 12.50* 12.50 11.45
14 G1UA030S14 1000 29.2 20.7 11.85* 11.85 10.80
14 G1UA036S14 1000 30.4 21.6 12.00* 12.00 11.10
17,21 G1UA036S17,21 1000 30.0 21.3 12.00* 12.00 11.00
17 G1UA048S17 1000 31.2 22.3 12.50* 12.50 11.45
21 G1UA048S21 1000 31.2 22.3 12.50* 12.50 11.35
17 G2FD030(S,H)17 1000 30.0 21.3 12.00* 12.00 11.00
14 G2FD035(S,H)14 1000 30.0 21.3 12.00* 12.00 11.00
17 G2FD036(S,H)17 1000 30.6 21.8 12.25* 12.25 11.20
21 G2FD036(S,H)21 1000 30.8 21.9 12.25* 12.25 11.25
21 G2FD042(S,H)21 1000 31.0 22.1 12.50* 12.50 11.35
17 G2FD046(S,H)17 1000 31.4 22.3 12.50* 12.50 11.45
For Notes See Page 5.

036-21106-005 Rev. B (0505)
Unitary Products Group 7
*Requires 2FD Blower Time Delay unless a standard furnace is equipped with one.
** Refer to Quick Selection Chart for specific furnace match-up.
AC036X1222 1050
1350
14 G1FA036S14 1200 33.6 23.4 11.50* 11.50 10.60
17,21 G1FA036S17,21 1200 33.0 23.0 11.25* 11.25 10.45
17 G1FA048S17 1200 35.0 24.4 12.00* 12.00 10.90
21 G1FA048S21 1200 34.0 25.2 12.00* 12.00 10.70
14 G1HA036H14 1150 33.5 23.8 12.00* –10.75
14 G1HA036H14 1150 33.4 23.7 –12.00* 10.75
17 G1HA036H17 1200 34.0 24.5 12.00* –10.80
17 G1HA036H17T 1200 34.0 24.5 –12.00* 10.80
21 G1HA048H21 1200 34.0 24.8 12.00* –10.70
21 G1HA048H21T 1200 33.3 24.3 –12.00 10.70
- G1HD036 1200 34.0 23.7 11.80* 11.80 10.70
- G1HD048 1200 35.4 24.7 12.00* 12.00 11.00
17 G1NA036S17L 1200 35.0 24.8 12.00* 12.00 10.90
21 G1NA048S21D 1200 35.0 24.8 12.00* 12.00 10.90
14 G1UA036S14 1200 33.6 23.4 11.50* 11.50 10.60
17,21 G1UA036S17,21 1200 33.0 23.0 11.25* 11.25 10.45
17 G1UA048S17 1200 35.0 24.4 12.00* 12.00 10.90
21 G1UA048S21 1200 34.0 25.2 12.00* 12.00 10.70
21 G1NA048S21D 1200 35.0 25.2 12.00* 12.00 10.40
14 G2FD035(S,H)14 1200 33.0 23.0 11.25* 11.25 10.45
17 G2FD036(S,H)17 1200 33.8 23.6 11.50* 11.50 10.70
21 G2FD036(S,H)21 1200 34.2 23.8 12.50* 12.50 10.75
21 G2FD042(S,H)21 1200 34.6 24.1 12.00* 12.00 10.80
17 G2FD046(S,H)17 1200 35.0 24.4 12.00* 12.00 10.90
21,24 G2FD048(S,H)21,24 1200 36.0 25.1 12.10* 12.10 11.10
AC042X1221 1225
1575
17 G1FA048S17 1400 42.0 30.2 –12.00* 10.60
21 G1FA048S21 1400 41.5 29.7 –12.00 10.65
21,24 G1FA060S21,24 1400 43.0 30.7 –12.50 10.95
21 G1HA048H21 1400 41.5 30.3 12.00* –10.65
21 G1HA048H21T 1400 40.7 29.7 –12.00 10.65
- G1HD048 1400 41.5 29.7 –12.00 10.60
21 G1NA048S21D 1400 41.0 28.6 –12.00* 10.40
17 G1UA048S17 1400 42.0 30.2 –12.00* 10.60
21 G1UA048S21 1400 41.5 29.7 –12.00 10.65
21,24 G1UA060S21,24 1400 43.0 30.7 –12.50* 10.95
21 G2FD042(S,H)21 1400 41.0 29.3 –12.00* 10.50
17 G2FD046(S,H)17 1400 42.0 30.2 –12.00* 10.60
21,24 G2FD048(S,H)21,24 1400 42.5 30.6 –12.00 10.75
AC048X1222 1375
1775
17 G1FA048S17 1575 45.5 34.1 12.00* 12.00 11.00
21 G1FA048S21 1575 46.5 34.9 12.00* 12.00 11.00
21,24 G1FA060S21,24 1575 48.0 36.0 12.50* 12.50 11.10
21 G1HA048H21 1550 46.0 33.6 12.00* –11.10
21 G1HA048H21T 1525 46.0 33.6 –12.00* 11.11
24 G1HA060H24 1575 47.0 33.8 12.00* –11.10
24 G1HA060H24T 1575 47.0 33.8 –12.00* 11.10
- G1HD048 1575 46.0 34.5 12.00* 12.00 10.80
- G1HD060 1575 47.5 35.6 12.40* 12.40 11.05
21 G1NA048S21D 1575 46.0 34.5 12.00* 12.00 10.70
17 G1UA048S17 1575 45.5 34.1 12.00* 12.00 11.00
21 G1UA048S21 1575 46.5 34.9 12.00* 12.00 11.00
21,24 G1UA060S21,24 1575 48.0 36.0 12.50* 12.50 11.10
17 G2FD046(S,H)17 1575 45.5 34.1 12.00* 12.00 10.80
21,24 G2FD048(S,H)21,24 1575 46.5 34.9 12.20* 12.20 10.90
24 G2FD060(S,H)24 1575 48.0 36.0 12.50* 12.50 11.10
24 G2FD061H24 1575 48.5 36.4 12.50* 12.50 11.20
AC060X1224 1600
2000
21 G1FA060S21(T) 1800 56.5 43.4 –12.00 10.10
- G1HD060 1800 55.5 42.8 –11.75 10.00
24 G1NA060S24T 1800 55.5 42.1 –11.75 10.00
21 G1UA060S21(T) 1800 56.5 43.4 –12.00 10.10
24 G2FD060(S,H)24(T) 1800 56.5 43.4 –12.00 10.10
24 G2FD061H24 1800 56.5 43.8 –12.00 10.15
24 G1HA60S24(T) 1710 56.0 42.5 –12.00 10.15
1 TXV = Use 1TV700 Series Kit.
COOLING CAPACITY - Upflow, Downflow & Horizontal Furnaces and Coils (Continued)
UNIT MODEL FURNACE** COIL
MODEL
COOLING
CFM RANGE
(MIN.-MAX.) WRATED
CFM NET MBH SEER W/O TXV SEER + TXV1EER
TOTAL SENS.

036-21106-005 Rev. B (0505)
8Unitary Products Group
1. For condensing unit only. Does not include effect of evaporator motor power or heat.
2. Performance based on 15° superheat and 15° sub-cooling at condensing unit.
a. Increase capacity 1% for each 2° increase in sub-cooling.
b. Decrease capacity 1% for each 2° decrease in sub-cooling.
3. Sub-cooling in excess of 20° may result in excessively high condensing temperature with air on condenser above 115°. Maximum
recommended condensing temperature is 140°F.
ACCESSORIES
Refer to Price Manual for specific model numbers.
Hard Start Kit - Provides increased starting torque for areas
with low voltage.
Compressor Blanket - Designed to further reduce the nor-
mal compressor operating sound. Refer to price pages for
specific match-ups.
Off Cycle Timer Delay - Provides a 5-minute off cycle to pre-
vent rapid recycling of the compressor.
Room Thermostats - A wide selection of compatible thermo-
sets are available to provide optimum performance and fea-
tures for any installation.
1 Heat Stage only, manual, mechanical thermostat. Add sub-
base for 1H/1C.
1H/1C, manual change-over electronic non-programmable
thermostat.
1H/1C, auto/manual changeover, electronic programmable,
deluxe 7-day, thermostat.
1H/1C, auto/manual changeover, electronic programmable.
* For the most current accessory information, refer to the
price book or consult factory.
SOUND POWER RATINGS
*Rated in accordance with ARI Standard 270.
COOLING PERFORMANCE
MODEL SUCT. T/P
@ COMPR. AIR TEMP ON CONDENSER MODEL SUCT. T/P
@ COMPR. AIR TEMP ON CONDENSER
75°F95°F115°F75°F95°F115°F
TEMP. PSIG MBH KW MBH KW MBH KW TEMP. PSIG MBH KW MBH KW MBH KW
AC018X1222
35 61.5 17.19 1.44 13.89 1.59 11.63 1.70
AC042X1221
35 61.5 35.94 3.12 31.92 3.76 27.86 4.54
40 68.5 18.77 1.45 15.80 1.63 13.53 1.77 40 68.5 39.29 3.15 35.11 3.77 30.80 4.55
45 76.0 20.48 1.47 17.70 1.66 15.04 1.83 45 76.0 42.48 3.21 38.17 3.84 33.70 4.63
50 84.0 21.99 1.48 19.60 1.70 16.81 1.89 50 84.0 45.62 3.23 41.40 3.92 36.56 4.39
AC024X1222
35 61.5 20.81 1.81 16.82 2.00 14.07 2.14
AC048X1222
35 61.5 40.62 3.39 36.09 4.08 31.50 4.91
40 68.5 22.73 1.83 19.13 2.05 16.37 2.23 40 68.5 44.42 3.41 39.69 4.09 34.83 4.94
45 76.0 24.80 1.85 21.43 2.09 18.20 2.31 45 76.0 48.02 3.47 43.16 4.16 38.10 5.02
50 84.0 26.63 1.86 23.73 2.14 20.36 2.37 50 84.0 51.58 3.50 46.81 4.25 41.33 4.76
AC030X1222
35 61.5 26.48 2.34 21.42 2.59 17.91 2.77
AC060X1223
35 61.5 50.26 4.42 44.64 5.32 38.97 6.42
40 68.5 28.94 2.36 24.34 2.65 20.84 2.92 40 68.5 54.95 4.46 49.10 5.33 43.08 6.44
45 76.0 31.56 2.39 27.07 2.71 23.17 2.96 45 76.0 59.41 4.54 53.38 5.43 47.13 6.55
50 84.0 33.89 2.40 30.20 2.77 25.92 3.07 50 84.0 63.81 4.58 57.90 5.55 51.13 6.22
AC036X1222
35 61.5 29.38 2.76 23.75 3.06 19.87 3.26
40 68.5 32.09 2.78 27.00 3.13 23.12 3.40
45 76.0 35.01 2.81 30.25 3.19 25.70 3.51
50 84.0 37.59 2.83 33.50 3.26 28.74 3.62
UNIT MODEL (dBA)*
018 75
024 80
030 76
036 79
042 78
048 80
060 76

036-21106-005 Rev. B (0505)
Unitary Products Group 9
TYPICAL INSTALLATION
TYPICAL FIELD WIRING - 1 Phase Application
MINIMUM 18” SERVICE ACCESS
CLEARANCE ON ONE SIDE
60” OVERHEAD
CLEARANCE
10” CLEARANCE
COIL AREA
WEATHERPROOF
DISCONNECT
SWITCH
THERMOSTAT TO FURNACE OR
AIR HANDLER
TERMINAL BLOCK
NEC CLASS 1 WIRING
NEC CLASS 2 WIRING
TO INDOOR COIL
SEAL OPENING(S) WITH
PERMAGUM OR EQUIVALENT
CONTROL ACCESS PANEL
NOTE: ALL OUTDOOR WIRING
MUST BE WEATHERPROOF.
ALL FIELD WIRING TO BE IN ACCORDANCE WITH ELECTRIC CODE (NEC) AND/OR LOCAL CODES
POWER WIRING
208/230-1-60
CONTACTOR
TERMINALS
COIL
GND.
LUG
CYRGW
YRGW
POWER WIRING
CONTROL WIRING
FACTORY WIRING
24 VOLT CONTROL WIRING
MINIMUM 18 GA. WIRE
(NEC CLASS 2) FURNACE OR AIR HANDLER TERMINAL BLOCK
ROOM THERMOSTAT
CONDENSING UNIT
ALL OUTDOOR WIRING MUST BE WEATHERPROOF. USE COPPER CONDUCTORS ONLY.
TERMINAL W IS ONLY
REQUIRED ON SYSTEMS
WITH HEAT.
*
*

036-21106-005 Rev. B (0505)
10 Unitary Products Group
Multipliers for determining the performance with other indoor sections.
NOTE: For dry bulb temperatures different than those listed (between 73-87 F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the
listed temperature and decreases by 1060 BTUH per 1000 CFM per degree belowthe listed temperature.
COOLING PERFORMANCE DATA
AIR CONDITIONER MODEL NO. AC018X1222
INDOOR COIL MODEL NO. G1FA024S14,17
CONDENSING|
ENTERING AIR
TEMPERATURE
IDCFM 500 650 800
ID DB (°F) 85 80 75 85 80 75 85 80 75
ID WB (°F) 72 67 63 72 67 63 72 67 63
75 T.C. 20.1 19.3 18.2 20.1 19.4 18.6 20.1 19.5 18.9 S.C. 11.711.511.312.112.212.212.512.813.1
KW 1.26 1.25 1.25 1.27 1.26 1.26 1.27 1.26 1.26
85 T.C. 19.8 18.7 17.0 20.0 19.1 17.7 20.3 19.5 18.3 S.C. 11.711.410.912.712.512.113.613.513.4
KW 1.37 1.35 1.34 1.37 1.36 1.35 1.38 1.37 1.36
95 T.C. 19.5 18.1 15.8 20.0 19.2 16.7 20.5 19.5 17.7 S.C. 11.711.310.413.213.012.014.714.213.6
KW 1.47 1.45 1.43 1.48 1.47 1.45 1.49 1.48 1.46
105 T.C. 18.1 16.3 14.2 18.7 17.1 15.0 19.4 17.8 15.8 S.C. 11.3 10.6 9.7 13.0 12.2 11.3 14.7 13.8 12.9
KW 1.58 1.55 1.52 1.59 1.57 2.53 1.61 1.58 3.54
115 T.C. 16.6 14.5 12.7 17.5 15.3 13.2 18.3 16.1 13.8 S.C. 10.8 9.8 9.1 12.7 11.6 10.6 14.7 13.4 12.1
KW 1.69 1.65 1.61 1.71 1.67 3.62 1.73 1.69 5.62
125 T.C. 15.2 12.7 11.1 16.2 13.6 11.5 17.3 14.5 11.9 S.C. 10.4 9.1 8.4 12.5 11.1 9.9 14.6 13.0 11.4
KW 1.79 1.75 1.70 1.82 1.77 4.70 1.85 1.79 7.70
NOTE: ALL CAPACITIES ARE NET WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM.
Air Handler Coil T.C. S.C. KW
F2RC/F2FC024 1.04 1.17 1.01
F2RP/F2FP024 1.04 1.04 1.01
N1AHB0806 G2FD024(S,H)14,17 1.02 1.02 1.00
G1HD024 1.04 1.04 1.01
G1NA030S17K 1.04 1.04 1.01
G1NA030S21M 1.04 1.17 1.01
G1UA024S14,17 1.00 1.00 1.00
G2FD024(S,H)14,17 1.02 1.02 1.00
G2FD030(S,H)17 1.04 1.04 1.01

036-21106-005 Rev. B (0505)
Unitary Products Group 11
Multipliers for determining the performance with other indoor sections.
NOTE: For dry bulb temperatures different than those listed (between 73-87 F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the
listed temperature and decreases by 1060 BTUH per 1000 CFM per degree belowthe listed temperature.
COOLING PERFORMANCE DATA
AIR CONDITIONER MODEL NO. AC24X1222
INDOOR COIL MODEL NO. G1FA036S17,21
CONDENSING
ENTERING AIR
TEMPERATURE
IDCFM 600 800 1000
ID DB (°F) 85 80 75 85 80 75 85 80 75
ID WB (°F) 72 67 63 72 67 63 72 67 63
75 T.C. 25.4 24.2 22.5 25.6 24.5 23.2 25.8 24.9 23.9 S.C. 14.6 14.6 13.8 15.4 15.6 15.4 16.3 16.6 17.1
KW 1.61 1.60 1.59 1.61 1.60 1.59 1.62 1.61 1.60
85 T.C. 24.9 23.6 21.4 25.1 23.9 22.2 25.3 24.2 23.0 S.C. 14.8 14.7 13.8 15.9 16.1 15.6 17.0 17.5 17.5
KW 1.75 1.74 1.71 1.76 1.75 1.73 1.78 1.76 1.74
95 T.C. 24.4 23.0 20.3 24.6 23.2 21.2 24.8 23.5 22.2 S.C. 14.9 14.7 13.7 16.3 16.6 15.8 17.7 18.4 17.9
KW 1.90 1.88 1.84 1.92 1.89 1.86 1.93 1.90 1.88
105 T.C. 22.9 20.8 18.2 23.3 21.4 19.1 23.8 22.0 20.0 S.C. 14.5 13.8 12.9 16.3 16.0 15.0 18.1 18.1 17.2
KW 2.04 2.01 1.96 2.07 2.02 1.98 2.09 2.04 2.00
115 T.C. 21.3 18.6 16.2 22.0 19.5 17.0 22.8 20.5 17.7 S.C. 14.0 12.9 12.0 16.3 15.3 14.2 18.6 17.8 16.4
KW 2.19 2.13 2.08 2.22 2.16 2.10 2.25 2.18 2.12
125 T.C. 19.8 16.4 14.2 20.7 17.6 14.9 21.8 19.0 15.4 S.C. 13.5 12.0 11.1 16.3 14.6 13.4 19.1 17.5 15.6
KW 2.34 2.25 2.20 2.37 2.30 2.22 2.41 2.32 2.24
NOTE: ALL CAPACITIES ARE NET WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM.
Air Handler Coil T.C. S.C. KW
F2RP/F2FP024 0.99 1.01 1.00
F2RP/F2FP030 1.00 1.03 1.00
F2RC/F2FC024 0.98 1.01 1.00
F2RC/F2FC030 0.98 1.01 0.99
N1AHB0806 G2FD024(S,H)17 0.99 0.98 0.99
N1AHB0806 G2FD030(S,H)17 1.00 1.00 1.00
G1FA024S14,17 0.96 0.95 1.00
G1FA030S14 0.99 0.98 0.99
G1FA036S14 1.01 1.02 1.00
G1HD024 1.00 0.99 1.01
G1HD036 1.03 1.04 1.00
G1NA030S17K 1.00 1.00 1.00
G1NA030S21M 1.00 1.00 1.00
G1UA024S14,17 0.96 0.95 1.00
G1UA030S14 0.99 0.98 0.99
G1UA036S14 1.01 1.02 1.00
G1UA036S17,21 1.00 1.00 1.00
G2FD024(S,H)14,17 0.99 0.98 0.99
G2FD030(S,H)17 1.00 1.00 1.00
G2FD035(S,H)14 1.00 1.00 1.00
G2FD036(S,H)17 1.03 1.03 1.00

036-21106-005 Rev. B (0505)
12 Unitary Products Group
Multipliers for determining the performance with other indoor sections.
NOTE: For dry bulb temperatures different than those listed (between 73-87 F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the
listed temperature and decreases by 1060 BTUH per 1000 CFM per degree belowthe listed temperature.
COOLING PERFORMANCE DATA
AIR CONDITIONER MODEL NO. AC030X1222
INDOOR COIL MODEL NO. G1FA036S17,21
CONDENSING
ENTERING AIR
TEMPERATURE
IDCFM 800 1000 1200
ID DB (°F) 85 80 75 85 80 75 85 80 75
ID WB (°F) 72 67 63 72 67 63 72 67 63
75 T.C. 31.9 30.6 28.9 27.4 30.9 29.4 23.0 31.2 29.9 S.C. 18.9 19.1 18.9 19.7 20.1 20.3 20.5 21.2 21.8
KW 1.97 1.95 1.94 1.98 1.96 1.95 1.98 1.97 1.95
85 T.C. 31.4 29.3 27.0 28.2 30.1 28.9 25.0 30.6 30.9 S.C. 19.2 18.9 18.1 20.1 20.7 20.2 21.1 22.0 22.4
KW 2.16 2.13 2.09 2.15 2.15 2.13 2.14 2.16 2.16
95 T.C. 30.9 28.1 25.0 29.0 29.2 28.4 27.1 30.1 31.9 S.C. 19.5 18.7 17.3 20.6 20.7 20.1 21.6 22.8 22.9
KW 2.35 2.30 2.24 2.32 2.34 2.31 2.29 2.34 2.37
105 T.C. 28.6 25.5 22.3 28.2 26.8 24.6 27.9 27.8 26.8 S.C. 18.7 17.7 16.2 20.4 20.1 18.7 22.2 22.1 21.2
KW 2.53 2.45 2.40 2.53 2.49 2.44 2.53 2.51 2.48
115 T.C. 26.3 23.0 19.7 27.5 24.2 20.7 28.6 25.5 21.8 S.C. 17.9 16.7 15.2 20.3 19.0 17.3 22.8 21.3 19.5
KW 2.70 2.61 2.55 2.74 2.64 2.57 2.77 2.68 2.59
125 T.C. 24.0 20.4 17.0 26.7 21.7 16.8 29.4 23.2 16.7 S.C. 17.1 15.6 14.1 20.2 17.9 16.0 23.3 20.5 17.8
KW 2.88 2.76 2.70 2.94 2.79 2.70 3.00 2.84 2.69
NOTE: ALL CAPACITIES ARE NET WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM.
Air Handler Coil T.C. S.C. KW
F2RP/F2FP030 1.01 1.08 0.99
F2RP/F2FP036 1.03 1.10 1.01
F2RC/F2FC030 0.99 1.01 0.99
F2RC/F2FC036 1.03 1.05 1.01
N1AHB1206 G2FD030(S,H)17 1.00 1.00 1.00
N1AHB1206 G2FD036(S,H)17 1.02 1.03 1.00
G1FA030S14 0.97 0.98 0.99
G1FA036S14 1.01 1.02 1.00
G1FA048S17 1.04 1.05 1.00
G1FA048S21 1.04 0.99 1.01
G1HD036 1.03 1.03 1.00
G1NA036S17L 1.05 1.05 1.01
G1NA030S17K 1.01 1.01 1.00
G1NA030S21M 1.01 1.01 1.00
G1UA030S14 0.97 0.98 0.99
G1UA036S14 1.01 1.02 1.00
G1UA036S17,21 1.00 1.00 1.00
G1UA048S17 1.04 1.05 1.00
G1UA048S21 1.04 0.99 1.01
G2FD030(S,H)17 1.00 1.00 1.00
G2FD035(S,H)14 1.00 1.00 1.00
G2FD036(S,H)17 1.02 1.03 1.00
G2FD036(S,H)21 1.03 1.03 1.00
G2FD042(S,H)21 1.03 1.04 1.00
G2FD046(S,H)17 1.05 1.05 1.01

036-21106-005 Rev. B (0505)
Unitary Products Group 13
Multipliers for determining the performance with other indoor sections.
NOTE: For dry bulb temperatures different than those listed (between 73-87 F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the
listed temperature and decreases by 1060 BTUH per 1000 CFM per degree belowthe listed temperature.
COOLING PERFORMANCE DATA
AIR CONDITIONER MODEL NO. AC036X1222
INDOOR COIL MODEL NO. G1FA048S21
CONDENSING
ENTERING AIR
TEMPERATURE
IDCFM 1000 1200 1400
ID DB (°F) 85 80 75 85 80 75 85 80 75
ID WB (°F) 72 67 63 72 67 63 72 67 63
75 T.C. 36.7 34.3 32.3 36.9 34.9 32.8 37.2 35.4 33.2 S.C. 23.2 22.8 22.5 24.3 24.2 23.9 25.4 25.6 25.4
KW 2.31 2.30 2.27 2.33 2.30 2.28 2.34 2.31 2.30
85 T.C. 35.3 33.1 30.9 35.7 33.7 31.4 36.2 34.2 31.9 S.C. 23.2 22.6 21.9 24.8 24.3 23.6 26.3 26.0 25.3
KW 2.51 2.48 2.45 2.53 2.50 2.47 2.54 2.51 2.48
95 T.C. 34.0 31.9 29.6 34.5 33.6 30.0 35.1 33.0 30.5 S.C. 23.3 22.4 21.3 25.3 23.4 23.3 27.3 26.4 25.2
KW 2.71 2.67 2.64 2.73 2.73 2.66 2.74 2.71 2.67
105 T.C. 31.8 29.5 27.2 32.3 30.0 27.6 32.9 30.5 28.0 S.C. 22.6 21.6 20.5 24.8 23.7 22.5 26.9 25.8 24.5
KW 2.93 2.88 2.82 2.94 2.90 2.85 2.96 2.92 2.87
115 T.C. 29.6 27.2 24.8 30.1 27.6 25.1 30.6 28.0 25.4 S.C. 22.0 20.8 19.7 24.3 23.0 21.8 26.6 25.2 23.9
KW 3.15 3.09 3.01 3.16 3.11 3.04 3.18 3.13 3.07
125 T.C. 27.3 24.8 22.4 27.8 25.2 22.6 28.4 25.5 22.9 S.C. 21.4 20.0 19.0 23.8 22.3 21.1 26.2 24.6 23.2
KW 3.36 3.29 3.19 3.38 3.31 3.23 3.39 3.33 3.26
NOTE: ALL CAPACITIES ARE NET WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM.
Air Handler Coil T.C. S.C. KW
F2RC/F2FC036 1.02 1.04 1.00
F2RP/F2FP036 1.02 1.03 1.00
F2RP/F2FP042 1.02 1.04 1.02
F2FP048 1.04 1.06 1.02
N1AHB1206 G2FD036(S,H)17 0.99 0.94 0.99
N1AHB1206 G2FD046(S,H)17 1.03 0.97 1.01
G1FA036S17,21 0.97 0.91 0.99
G1FA036S14 0.99 0.93 1.00
G1FA048S17 1.03 0.97 1.01
G1HD036 1.00 0.94 1.00
G1HD048 1.04 0.98 1.01
G1NA048S21D 1.03 0.99 1.01
G1NA036S17L 1.03 0.99 1.01
G1UA036S17,21 0.97 0.91 0.99
G1UA036S14 0.99 0.93 1.00
G1UA048S17 1.03 0.97 1.01
G1UA048S21 1.00 1.00 1.00
G2FD035(S,H)14 0.97 0.91 0.99
G2FD036(S,H)17 0.99 0.94 0.99
G2FD036(S,H)21 1.01 0.95 1.00
G2FD042(S,H)21 1.02 0.96 1.01
G2FD046(S,H)17 1.03 0.97 1.01
G2FD048(S,H)21,24 1.06 1.00 1.02

036-21106-005 Rev. B (0505)
14 Unitary Products Group
Multipliers for determining the performance with other indoor sections.
NOTE: For dry bulb temperatures different than those listed (between 73-87 F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the
listed temperature and decreases by 1060 BTUH per 1000 CFM per degree belowthe listed temperature.
COOLING PERFORMANCE DATA
AIR CONDITIONER MODEL NO. AC042X1221
INDOOR COIL MODEL NO. G1FA048S21
CONDENSING
ENTERING AIR
TEMPERATURE
IDCFM 1200 1400 1600
ID DB (°F) 85 80 75 85 80 75 85 80 75
ID WB (°F) 72 67 63 72 67 63 72 67 63
75 T.C. 46.4 45.7 43.0 46.4 45.9 43.3 46.5 46.0 43.5 S.C. 27.0 27.5 27.8 27.9 29.0 29.5 28.8 30.5 31.2
KW 2.45 2.44 2.45 2.47 2.45 2.46 2.48 2.45 2.46
85 T.C. 45.5 44.1 41.1 45.6 44.4 41.6 45.7 44.7 42.0 S.C. 27.5 27.5 27.2 28.6 29.2 29.1 29.7 30.9 31.0
KW 2.76 2.75 2.75 2.77 2.76 2.76 2.78 2.76 2.76
95 T.C. 44.6 42.5 39.2 44.8 43.0 39.8 45.0 43.4 40.4 S.C. 28.0 27.6 26.5 29.3 29.5 28.6 30.7 31.4 30.7
KW 3.07 3.06 3.05 3.08 3.07 3.06 3.09 3.07 3.06
105 T.C. 43.7 41.0 37.4 43.9 41.5 38.1 44.2 42.0 38.9 S.C. 28.4 27.6 25.9 30.0 29.7 28.2 31.6 31.8 30.5
KW 3.39 3.38 3.36 3.39 3.38 3.36 3.40 3.39 3.37
115 T.C. 41.2 38.1 34.1 41.6 38.7 34.9 42.0 39.3 35.7 S.C. 27.8 26.7 24.8 29.8 28.9 27.0 31.8 31.0 29.2
KW 3.80 3.77 3.73 3.81 3.78 3.74 3.81 3.79 3.75
125 T.C. 38.7 35.3 30.9 39.3 35.9 31.8 39.9 36.5 32.6 S.C. 27.1 25.7 23.7 29.5 28.0 25.8 31.9 30.3 27.9
KW 4.21 4.16 4.11 4.22 4.18 4.12 4.23 4.19 4.13
NOTE: ALL CAPACITIES ARE NET WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM.
Air Handler Coil T.C. S.C. KW
F2RP/F2FP042 1.02 1.04 1.02
F2FP048 1.04 1.06 1.02
N1AHC1606 G2FD042(S,H)21 0.99 0.99 1.00
N1AHC1606 G2FD048(S,H)21 1.02 1.03 1.02
G1FA048S17 1.01 1.02 1.02
G1FA060S21,24 1.04 1.03 1.01
G1HD048 1.00 1.00 1.01
G1NA048S21D 0.99 0.96 1.01
G1UA048S17 1.01 1.02 1.02
G1UA048S21 1.00 1.00 1.00
G1UA060S21,24 1.04 1.03 1.01
G2FD042(S,H)21 0.99 0.99 1.00
G2FD046(S,H)17 1.01 1.02 1.02
G2FD048(S,H)21,24 1.02 1.03 1.02

036-21106-005 Rev. B (0505)
Unitary Products Group 15
Multipliers for determining the performance with other indoor sections.
NOTE: For dry bulb temperatures different than those listed (between 73-87 F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the
listed temperature and decreases by 1060 BTUH per 1000 CFM per degree belowthe listed temperature.
COOLING PERFORMANCE DATA
AIR CONDITIONER MODEL NO. AC048X1222
INDOOR COIL MODEL NO. G1FA048S21
CONDENSING
ENTERING AIR
TEMPERATURE
IDCFM 1375 1575 1775
ID DB (°F) 85 80 75 85 80 75 85 80 75
ID WB (°F) 72 67 63 72 67 63 72 67 63
75 T.C. 52.8 49.9 45.4 53.5 50.6 46.8 54.2 51.3 48.2 S.C. 33.3 32.7 31.5 34.9 34.5 33.6 36.5 36.2 35.7
KW 3.14 3.09 3.03 3.15 3.10 3.04 3.17 3.12 3.06
85 T.C. 50.9 47.1 42.4 51.6 48.1 43.5 52.3 49.1 44.7 S.C. 33.3 32.0 30.4 35.3 34.2 32.6 37.4 36.3 34.7
KW 3.44 3.35 3.30 3.46 3.38 3.31 3.47 3.40 3.32
95 T.C. 49.0 44.3 39.4 49.7 45.5 40.3 50.3 46.8 41.2 S.C. 33.2 31.2 29.3 35.8 34.1 31.5 38.4 36.5 33.7
KW 3.74 3.62 3.57 3.76 3.56 3.57 3.78 3.69 3.58
105 T.C. 44.7 40.0 35.8 45.4 41.0 36.5 46.1 42.0 37.1 S.C. 31.9 29.8 27.8 34.5 32.2 29.9 37.0 34.7 32.1
KW 4.01 3.89 3.80 4.04 3.91 3.81 4.07 3.94 3.83
115 T.C. 40.5 35.7 32.1 41.2 36.5 32.6 41.9 37.2 33.1 S.C. 30.5 28.3 26.3 33.1 30.5 28.4 35.7 32.8 30.5
KW 4.28 4.15 4.02 4.32 4.17 4.05 4.35 4.19 4.08
125 T.C. 36.3 31.3 28.5 36.9 31.9 28.8 37.6 32.5 29.1 S.C. 29.2 26.8 24.8 31.8 28.9 26.8 34.4 31.0 28.8
KW 4.55 4.42 4.25 4.60 4.43 4.29 4.64 4.44 4.33
NOTE: ALL CAPACITIES ARE NET WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM.
Air Handler Coil T.C. S.C. KW
F2FP048 1.00 1.00 1.02
F2FP060 1.03 1.03 1.06
N1AHC1606 G2FD048(S,H)21,24 1.00 1.00 1.01
N1AHD2006 G2FD060(S,H)24 1.03 1.03 1.02
N1AHD2006 G2FD061H24 1.04 1.04 1.02
G1FA048S17 0.98 0.98 0.98
G1FA060S21,24 1.03 1.03 1.02
G1HD048 0.99 0.99 1.01
G1HD060 1.02 1.02 1.02
G1NA048S21D 0.99 0.99 1.02
G1UA048S17 0.98 0.98 0.98
G1UA048S21 1.00 1.00 1.00
G1UA060S21,24 1.03 1.03 1.02
G2FD046(S,H)17 0.98 0.98 1.00
G2FD048(S,H)21,24 1.00 1.00 1.01
G2FD060(S,H)24 1.03 1.03 1.02
G2FD061H24 1.04 1.04 1.02

036-21106-005 Rev. B (0505)
16 Unitary Products Group
Multipliers for determining the performance with other indoor sections.
NOTE: For dry bulb temperatures different than those listed (between 73-87 F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the
listed temperature and decreases by 1060 BTUH per 1000 CFM per degree belowthe listed temperature.
COOLING PERFORMANCE DATA
AIR CONDITIONER MODEL NO. AC060X1224
INDOOR COIL MODEL NO. G1FA060S21,24
CONDENSING
ENTERING AIR
TEMPERATURE
IDCFM 1600 1800 2000
ID DB (°F) 70 75 80 85 70 75 80 85 70 75 80 85
ID WB (°F) 57 63 67 72 57 63 67 72 57 63 67 72
75 T.C. 53.8 59.2 63.5 68.4 54.8 60.2 64.5 69.5 55.2 60.7 64.9 70.1 S.C. 45.6 42.7 44.1 43.6 47.9 45.3 46.6 46.2 49.4 46.9 48.4 47.9
KW 13.8 14.9 15.8 16.9 13.7 14.9 15.7 16.8 13.6 14.7 15.6 16.6
85 T.C. 51.6 56.8 60.9 65.7 52.5 57.7 61.8 66.6 53.0 58.2 62.2 67.1 S.C. 44.4 41.7 43.1 42.7 46.7 44.2 45.5 45.1 48.3 45.7 47.2 46.8
KW 11.8 12.7 13.5 14.4 11.7 12.7 13.5 14.4 11.6 12.6 13.3 14.2
95 T.C. 49.5 54.7 58.6 63.2 50.3 55.5 59.3 64.1 50.8 55.9 59.8 64.5 S.C. 43.2 41.0 42.0 41.8 45.5 43.2 44.5 44.2 47.1 44.7 46.3 45.8
KW 10.3 11.2 11.8 12.6 10.2 11.1 11.8 12.6 10.2 11.0 11.7 12.5
105 T.C. 47.2 52.2 55.8 60.3 47.9 52.8 56.5 60.9 48.4 53.3 56.8 61.2 S.C. 42.1 39.8 41.2 40.9 44.2 41.9 43.4 43.1 46.0 43.4 44.7 44.4
KW 8.8 9.6 10.2 10.9 8.8 9.5 10.1 10.8 8.8 9.5 10.0 10.7
115 T.C. 44.7 49.4 52.9 57.1 45.4 50.0 53.4 57.6 45.7 50.4 53.7 57.9 S.C. 40.6 38.6 39.8 39.6 43.1 40.6 41.9 41.6 44.6 42.4 43.5 43.2
KW 7.5 8.1 8.6 9.3 7.5 8.1 8.6 9.2 7.4 8.1 8.5 9.1
125 T.C. 42.3 46.7 50.1 53.9 42.9 47.4 50.4 54.4 43.4 47.8 50.9 54.6 S.C. 39.4 37.5 38.8 38.2 41.8 39.7 40.6 40.4 43.3 41.2 42.6 42.1
KW 6.3 6.9 7.3 7.8 6.3 6.9 7.3 7.8 6.3 6.9 7.3 7.7
NOTE: ALL CAPACITIES ARE NET WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM.
Air Handler Coil T.C. S.C. KW
F3FP060 0.99 0.97 1.00
F3FV060 0.99 0.97 0.97
N1VSD20 G2FD060(S,H)24(T) 0.99 0.97 0.98
N1VSD20 G2FD061H24 1.00 0.98 0.97
N1AHD20 G2FD060(S,H)24(T) 1.00 1.00 1.00
N1AHD20 G2FD061H24 1.00 1.01 1.00
G1FA/G1UA060S21(T) 1.00 1.00 1.00
G2FD060(S,H)24(T) 1.00 1.00 1.00
G2FD061H24 1.00 1.01 1.00
G1NA060S24T 0.98 0.97 0.99
G1HD060 0.98 0.99 0.99
G1HA60S24(T) 0.99 0.98 0.99

036-21106-005 Rev. B (0505)
Unitary Products Group 17
MATCHING INDOOR COMPONENTS
G1UA
1/2 CASED
UPFLOW
G1HD
HORIZONTAL DUCT
G2FD*
MULTI-POSITION
(UPFLOW, HORIZONTAL
AND DOWNFLOW)
* Available with factoryinstalled horizontal drain pan.
ADD-ON COILS - FOR FURNACE APPLICATIONS
G1NA
UNCASED
UPFLOW
G1FA
FULL CASED
UPFLOW
AIR HANDLERS - FOR NON-FURNACE APPLICATIONS
N1AH OR N1VS
MODULAR BLOWER
(UPFLOW, HORIZONTAL
AND DOWNFLOW)
F2RC / F2FC OR
F2RP / F2FP / F2FV
FAN COIL UNITS (UPFLOW, HORIZONTAL)
F3RP / F3FP/
G2FD
COIL

036-21106-005 Rev. B (0505)
18 Unitary Products Group
NOTES

036-21106-005 Rev. B (0505)
Unitary Products Group 19
NOTES

Subject to change without notice. Printed in U.S.A. 036-21106-005 Rev. B (0505)
Copyright © by York International Corp. 2005. All rights reserved. Supersedes: 036-21106-005 Rev. A (0904)
Unitary 5005 Norman
Products York O
K
Group Drive 73069
NOTES