YOTRIO Target Fairmont GFS20403A User manual

Fairmont
8’ x 8’ adjustable shade pergola
style # GFS20403A
dpci # 009050057
>>assembly instructions TM

Congratulations on your latest Target purchase.
Now what? Don't start sweating over this box of parts. This will be easy. We did the hard work for you.
All you need to do is follow our simple instructions and you'll be on your way to transforming your patio in no time.
Good luck – though we're confident you won't need it.
ATTENTION:
This Pergola is not intended for use during any kind of inclement weather and the manufacturer is not
and can not be held responsible for any damages caused as a result of such weather. Weather-related
damage, or damage as a result of the Pergola not being stored properly when not in use is not the
responsibility of the manufacturer.
During extended periods of non-usage, off season, or in inclement weather (wind, rain, snow, hail,
sleet), freezing conditions and extreme heat, the Pergola needs to be stored in a dry sheltered place to
prolong the life and to avoid damage to the Pergola.
2
IMPORTANT WARNING:
Unpack the box on a clean soft level surface and make sure all parts have been included.
To replace missing or damaged parts please call 855-MYTGTHOME (855-698-4846) during 7am - 7pm CST M-F, and 8am - 5pm CST Saturday.

WARRANTY:
This Pergola comes with a one year limited warranty against original manufacture defects. If you experience
trouble with your pergola, please call the customer service number below.
3
Target Corporation
Toll Free at: 855-MYTGTHOME (855-698-4846) during 7am - 7pm CST M-F, and 8am - 5pm CST Saturday.
Code: Yotrio 2020
before you begin
1. Check for damage or missing parts. Call 855-MYTGTHOME (855-698-4846) to order missing supplies.
2. Use the carton as a working surface to prevent product damage during assembly.
3. Gather all tools prior to assembly.

table of contents
introduction
hardware
parts list
assembly
2-3
5
6
7-18
QUESTIONS?
4Please call 855-MYTGTHOME (855-698-4846) parts and service. For faster service, have th e style number and DPCI number ready when calling.

hardware
5
(Part N)×92
M6*15mm bolt with washer
(Part R)×2
allen wrench
(Part O)×10
M6*40mm bolt with washer
(Part P)×16
M6*55mm bolt with washer
(Part Q)×16
ground spike

ITEM DESCRIPTION QUANTITY
post leg2
connector bar1
2
2
2
A1
A2
B1
B2
6
2
connector bar2
post leg1
Ctop bar 5
Drail bar 4
E
F
G1
G2
H
I
shade rod 2
sling canopy 1
corner bracket1 4
corner bracket2 4
end tip 8
post decoration 4
J
K
L
M
post base 4
post base plate 4
8
4tube connector
duo tube connector
A2 A2
A1
A1
F
HCCC
H
CC
H
H
H
H
HH
I
I
I
M
M
M
M
M
M
D
D
D
D
E
E
L
L
L
K
K
K
K
J
J
J
J
G2
G2
G2
G2
G1
G1
G1
G1
I
B2
B2
B1
B1

7
step 01:
(Part N)×8
M6*15mm bolt with washer
(Part R)×1
allen wrench
A2
A1
I
I
I
K
K
K
J
N
N
A1 A2
&
A1 A2
&
Do not completely tighten screws until all screws are in place.
ATTENTION: To avoid damage to your new pergola, please
use either the carton or another soft surface such as carpet as a
working surface to prevent product damage during assembly.
1. Attach the post base plates (K) to the post leg1 & 2 (A1 & A2), then insert
the post base (J) into the post leg1 & 2 (A1 & A2), secure with M6*15mm
bolt with washer (N) using the allen wrench (R).
2. Attach the post decoration (I) to the post leg1 & 2 (A1 & A2).
3. Repeat above steps until the 4 post base plates (K), post base (J) and
post decoration (I) are secured to the post leg1 & 2 (A1 & A2).
3.
2.
1.

step 02:
8
A2
A2
A1
A1
B1
B1
B1
N
N
N
N
(Part N)×8
M6*15mm bolt with washer
(Part R)×1
allen wrench
Do not completely tighten screws until all screws are in place.
1. Place the post leg1 & 2 (A1 & A2) on the soft surface.
2. Attach the connector bar1 (B1) to the post leg1 & 2 (A1 & A2), secure with M6*15mm
bolt with washer (N) using the allen wrench (R).
3. Repeat above steps for the another set of post leg1 & 2 (A1 & A2) and connector bar1 (B1).
2.
1.
B1
A2
A1
B1
NOTE: Ensure the holes on the post leg1 & 2 (A1 & A2) face to center of the pergola.
4.
3.

9
step 03:
(Part N)×8
M6*15mm bolt with washer
(Part R)×1
allen wrench
A1
A1
A2
A2
B2
B1
B1
B2
B2 B2
B1B1
A1
A2
N
N
NN
Do not completely tighten screws until all screws are in place.
1. When the post leg1 & 2 (A1&A2) connections are made, set the post leg1 & 2 (A1 & A2)
upright.
2. Attach the connector bar2 (B2) to the post leg1 & 2 (A1 & A2), secure with M6*15mm
bolt with washer (N) using the allen wrench (R).
3. Repeat above steps for another set of post leg1 & 2 (A1 & A2) and connector bar2 (B2).
NOTE: Ensure the holes on the connector bar1 & 2 (B1 & B2) face to center of the pergola.

step 04:
(Part N)×16
M6*15mm bolt with washer
(Part R)×1
allen wrench
A1
A1
A2
A2
B1
B1
B2
B2
N
N
H
H
H
H
HH
A1
A2
&
B1 B2
&
B1 B2
&
10
Do not completely tighten screws until all screws are in place.
1. Attach the end tips (H) to the post leg1 & 2 (A1 & A2), secure with the
M6*15mm bolt with washer (N) using the allen wrench (R).