Zamel VO-811IDB User manual

ENTRANCE PANEL VO-811IDB / VO-811IDS
Thank you for buying this product from Zamel.
Zamel shall not accept any liability for any results of damage and/or accidents caused
by non-intended use of the product.
Before attempting installation of this product, please read and understand the entire
Operating Manual to comply with the intended use.
Do not open or tamper with the product without prior authorization.
Otherwise your warranty rights for this product will be void.
OPENING
Place the ID card close to the card reader. The Open LED will switch on and the buzzer will sound once.
OPENING TIME
The opening time default setting is 1 second. The time setting can be adjusted with the video entrance
phone display. The card reader will use the new opening time set with the display.
REGISTERING A NEW ID CARD
A single entrance panel can be linked to a total of 20 ID cards. The operating procedures are intuitive with
the light and sound indicators. The ID card readout distance from the card reader is 3 cm. Registering
and unregistering ID cards requires the MASTER card. Keep your MASTER card safe from unauthorized
use and damage. The ID card system frequency is 125 KHz / Wiegand 26.
AUTHORIZING THE MASTER CARD
When the entrance panel is used for the rst time, the call button LED will switch on and the buzzer will
sound steadily. Place an ID card close to the card reader. This card will be authorized as the MASTER
card by the entrance panel. The buzzer will then stop. Any ID card can be authorized as a MASTER any
time.
ADDING USER ID CARDS
Place the MASTER card close to the card reader. Now place the new ID card close to the card reader
to be registered. Place the MASTER card close to the card reader again to exit the ID card addition mode.
The button LED will continue to ash until you exit the ID card addition mode. If the ID card addition mode
is on without any interaction with the cards for 40 seconds, it will switch off.
UNREGISTERING THE MASTER AND ID CARDS
To unregister all ID cards from the entrance panel, move the MASTER card in and out of the card reader
range four times. The buzzer will sound and the button LED will ash. When the ID cards are unregistered,
you can authorize a new MASTER card immediately.
WIEGAND 26 READER
The entrance panel can be operated as a Wiegand 26 device. This requires disconnecting the Wiegand
1 wire (blue) and the common (GND) wire (brown). The ID card operability is disabled in the Wiegand
26 device mode.
CAUTION:
If the MASTER card is lost, remove the back plate of the entrance panel and press the RST button
beneath to restore all default settings. This will unregister all ID cards for the entrance panel. Follow
the procedures above to register your new MASTER and ID cards.
WARRANTY
24-month commercial warranty by the manufacturer
Reseller’s stamp and signature
with date of sale
1. ZAMEL Sp. z o.o. Gives a 24-month warranty for the goods it sells.
2. The warranty given by ZAMEL Sp. z o.o. does not cover:
a) mechanical damage caused by transport, loading/unloading
or other circumstances;
b) damage caused by improper installation or operation of the goods
manufactured by ZAMEL Sp. z o.o.;
c) damage caused by any modications made by the BUYER
or any third party to the sold goods or to the equipment required
for the proper functioning of the sold goods;
d) damage caused by any force majeure event or another fortuitous
event beyond any reasonable control of ZAMEL Sp. z o.o.;
e) the power supply (batteries) included (if any) with the device
as sold.
3. The BUYER shall make all warranty claims in writing at the point of sale or to ZAMEL Sp. z o.o.
4. ZAMEL Sp. z o.o. will examine each warranty claim as regulated by the applicable provisions of the Polish law.
5. The form of warranty claim resolution, i.e. replacement, repair or refund of the price of purchase, shall be decided
by ZAMEL Sp. z o.o.
6. This warranty does not exclude, limit or suspend any rights of the BUYER arising from the statutory
or regulatory laws concerning implied warranty for defects of sold goods.

SPECIFICATIONS
• Surface-mounted
• Vandal-resistant zinc alloy housing
• 800 TVL resolution
• ¼” CMOS colour camera
• Night-time IR illumination
• Dust and water proof: IP66
• Operating temperature: -30°C to +60°C
• 110° wide-angle camera
• Video output: 1Vp-p75Ω
• Supply voltage: 10-15 V DC
• Input power: 2.5 W
• Integrated 125 KHz ID reader
• Compliance with Wiegand 26 / ID
• Dimensions: 128x43x16 mm
1. Microphone
2. Camera
3. Night-time IR
illuminator
4. RFID proximity
reader
5. Call button
6. Speaker
INSTALLATION
1. Use the wiring connection diagram and verify
that all wiring connections are correct.
2. Choose a suitable location in which to install
the entrance panel. An installation height
between 1.5 and 1.6 m above the ground
is recommended.
3. The entrance panel video camera should be
away from direct sunlight and deep shadows.
4. Verify that the power supply voltage is OFF
before wiring the device.
5. Switch on the supply voltage of the device
when completely installed.
6. Seal the back plate edges of the entrance
panel of the complete installation surface with
a waterproof silicone product during
the installation. This will prevent condensation
occurring between the entrance panel and
its installation surface in certain weather
conditions. Condensation on the surfaces
causes a risk of corrosion of the electronic
components in the device and mechanical
stress from freezing of the condensation
at low temperatures.
PRODUCT DESCRIPTION
INSTALLATION DIAGRAM
A. Directly on a wall or a post 1. Select the installation height
of the entrance panel and drill the mounting
holes on the installation surface
at the desired height.
2. Remove the bracket by removing
its lock screw.
3. Mount the bracket on the installation surface
with wall plugs and their screws.
4. Pass the connection wiring end through the
bracket and connect it to the entrance panel
wiring. Follow the wiring connection diagram.
5. Install the entrance panel on the bracket with
the lock screw.
B. Directly on a wall or a post with
the 30° angle console
1. Select the installation height of the entrance
panel and drill the mounting holes on the
installation surface at the desired height.
2. Mount the 30° angle console on the installation
surface with wall plugs and their screws.
3. Remove the factory bracket from the entrance
panel back plate.
4. Install the removed bracket on the 30° angle
console with the screws provided.
5. Pass the connection wiring end through the
bracket and connect it to the entrance panel
wiring. Follow the wiring connection diagram.
6. Install the entrance panel on the bracket with
the lock screw.
WIRING CONNECTION DIAGRAM
1
2
3
4
5
6
Wiegand 26 wiring
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
Red
Blue
Yellow
White
Orange
Green
Brown
Purple
Grey
Black
Red
Blue
Yellow
White
Orange
Green
Brown
Purple
Grey
Black
Red
Blue
Yellow
White
Orange
Green
Brown
Purple
Grey
Black
Wiegand
26 reader ELECTRIC CATCH
Power +
Power - Power
(12V DC)
Power +
Power -
Power +
Power -
Power +
Power -
Power +
Power -
ELECTRIC CATCH
ELECTRIC CATCH
NO wiring
LOCK_Power
(5V~24V AC/DC)
CARD_Power
(12V DC)
NC wiring
LOCK_Power
(5V~24V AC/DC)
CARD_Power
(12V DC)
DISPLAY
DISPLAY
DISPLAY