Zamel P-257/2 User manual

OPERATION RANGE
* - 1-channel transmitters do not cooperate with roller blind controllers
CAUTION: The given range concerns open area - an ideal condition without any
natural or articial obstacles. If there are some obstacles between a transmitter
and a receiver, it is advisable to decrease the range according to: wood and plas-
ter: from 5 to 20 %, bricks: from 10 to 40 %, reinforced concrete: from 40 to 80 %,
metal: from 90 to 100% , glass: from 10 to 20 %, Over- and underground medium
and high electrical power lines, radio and television transmitters, GSM transmit-
ters set close to a device system have also a negative inuence on the range.
Symbol ROP-01 ROP-02 ROB-01 SRP-02 SRP-03 RWG-01 RWL-01 ROM-01 ROM-10 RDP-01 RTN-01
RNK-02 180 m 200 m 200 m 200 m 200 m 250 m 180 m 250 m 250 m 180 m 250 m
RNK-04 180 m 200 m 200 m 200 m 200 m 250 m 180 m 250 m 250 m 180 m 250 m
P-256/8 230 m 250 m 250 m 250 m 250 m 300 m 200 m 300 m 300 m 230 m 300 m
P-257/4 (2) 180 m 200 m 200 m 200 m 200 m 250 m 180 m 250 m 250 m 180 m 250 m
RNM-10 230 m 250 m 250 m 250 m 250 m 300 m 200 m 300 m 300 m 230 m 300 m
RNP-01 160 m 180 m 180 m 180 m 180 m 200 m 160 m 200 m 200 m 160 m 200 m
RNP-02 160 m 180 m 180 m 180 m 180 m 200 m 160 m 200 m 200 m 160 m 200 m
RNL-01 160 m 180 m 180 m no* no* 200 m 160 m 200 m 200 m 160 m 200 m
RTN-01 200 m 200 m 200 m 200 m 200 m 250 m 200 m 250 m 250 m 200 m 250 m
RCR-01 160 m 180 m 180 m no* no* 200 m 160 m 200 m 200 m 160 m 200 m
RTI-01 160 m 180 m 180 m 180 m 180 m 200 m 160 m 200 m 200 m 160 m 200 m
RXM-01 230 m 250 m 250 m 250 m 250 m 300 m 200 m 300 m 300 m 230 m 300 m
TIME PROGRAMMING
RADIO TRANSMITTERS DELETION
Press PROG push-button of RWG-01 device for a longer time till LED red diode switches
on (constant signal). Next release PROG push-button. Wait (for about 5 seconds) till LED
red diode switches on (rst signal pulsates, next the signal is constant).
Press PROG push-button of RWG-01 device and then release it. LED red diode switches
off and then switches on (signal pulsates). Every LED diode pulse equals 1 second.
After the adjusted time is nished (the number of LED red diode ashes) press PROG
push-button and then release it - TIME IS ADDED.
Maximum time is 18 hours.
Press PROG push-button of RWG-01 device for a longer time.
After 5 seconds LED red diode switches on (signal pulsates) and then it switches off.
Release the push-button in RWG-01 - MEMORY IS DELETED.
GNIAZDO ZDALNIE STEROWANE Z PILOTEM P-257/2
RWG-01K
TECHNICAL DATA
P-257/2 RWG-01
Input rated voltage: 3 V (battery CR2032) 230 V AC
Battery life: 3 ÷ 5 years -
Input voltage tolerance: - -15 ÷ +10 %
Nominal frequency: - 50 / 60 Hz
Nominal power consumption: - 0,29 W
Optic signalling of supply voltage: - LED green diode
Number of operation modes: - 5
Number of channels: 2 1
Transmission: radio 868,32 MHz
Coding way: unidirectional
Coding: addressing transmission
Maximum number of transmitters: - 32
Range:
up to 250 m in the open area up to 300 m in the open area
Time adjustment: - 1 s ÷ 18 h (every second)
Optic signalling of transmitter’s
operation: LED red diode
Relay contact parameters: - 1NO 16A / 250V AC
AC1 4000 VA
Ambient temperature range: -10 ÷ +55
o
C
Operating position: free
Mounting: -
230 V AC socket
Casing protection degree: IP20 (PN-EN 60529)
Protection level: III II
Overvoltage category: - II
Pollution degree: 2
Surge voltage: - 1 kV (PN-EN 61000-4-5)
Dimensions: 74 x 33 x 11,5 mm 160 x 66 x 90 mm
Weight: 0,020 kg 0,160 kg
Reference standard: PN-ETSI EN 300 220-1
PN-ETSI EN 300 220-2
PN-EN 60669, PN-EN 60950
PN-EN 61000
DESCRIPTION
Remote control socket RWG-01 is used to connect any 230 V AC receiver of 4000 VA
and to wireless control by means of different EXTA FREE system transmitters. The
device can be mounted without any additional tools or interference in existing wiring - it
is directly mounted to 230 V AC socket.

APPEARANCE
OPERATION P-257/2
After pressing the push-button the remote control sends a signal on 868,32 MHz which
controls EXTA FREE receivers. Device programming procedure (adding a transmit-
ter to the transmitter’s memory) is described in manual instruction of particular EXTA
FREE system receivers. The range (up to 250 m depending on a receiver) can be
changed by means of a retransmitter or few RTN-01 retransmitters.
BATTERY CHANGE
Battery discharge status is signalled by several LED red diode ashes during
transmission time.
1. Remove the screws from the bottom part of the remote control.
2. Remove the upper cover with the silicon keyboard.
3. Remove the battery from the latch.
4. Mount a new battery. Watch battery polarisation marked on the latch. Wrong
battery mounting may cause device damage.
5. Place back the top cover with the keyboard and tighten the screws.
CAUTION: While changing the battery, it is suggested to press any of the buttons
for about 5 seconds before putting it into a latch. Next press transmission button
several times to check its operation. If the transmitter does not work properly
repeat the battery change procedure.
RADIO TRANSMITTERS PROGRAMMING
OPERATION RWG-01
MONOSTABLE mode:
Press transmitter’s push-button for a longer time.
Press PROG push-button of RWG-01 device for a longer time until LED red diode
switches on (constant signal). Next release PROG push-button.
Release transmitter’s push-button. LED red diode switches on (rst signal pulsates,
next the signal is constant).
Press the same transmitter’s push-button and release it. LED red diode switches on
(the signal pulsates) and next it switches off - THE TRANSMITTER IS ADDED.
BISTABLE mode:
Press PROG push-button of RWG-01 device for a longer time until LED red diode
switches on (constant signal). Next release PROG push-button.
Press the transmitter’s push-button for a longer time. LED red diode switches on
(rst signal pulsates, next the signal is constant).
Release transmitter’s push-button. LED red diode switches on (the signal pulsates),
next the LED red diode switches off - it means the TRANSMITTER IS ADDED.
SWITCH ON/SWITCH OFF mode (two push-buttons):
Press PROG push-button of RWG-01 device for a longer time until LED red diode
switches on (constant signal). Next release PROG push-button.
Press and release transmitter’s rst push-button. LED red diode switches on (rst
signal pulsates, next the signal is constant).
Press and release the second transmitter’s push-button. LED red diode switches on
(the signal pulsates) and next it switches off - THE TRANSMITTER IS ADDED.
TIME mode (one push-button):
Press PROG push-button of RWG-01 device for a longer time till LED red diode
switches on (constant signal). Next release PROG push-button.
Press the transmitter’s push-button and then release it. LED red diode switches on
(rst signal pulsates, next the signal is constant).
Press and release the same transmitter’s push-button. LED red diode switches on
(signal pulsates) and then switches off - THE TRANSMITTER IS ADDED.
An exemplary programming procedure with the use of P-257/2 remote controller. The
procedure for the rest of radio EXTA FREE transmitters is analogous. CAUTION: Eve-
ry transmitter can cooperate with RWG-01 in a different mode, depending on
how they were added to the device. One transmitter can be added during one
programming cycle. Full memory is signalled with pulsating LED red diode.
The device can operate in ve modes:
MONOSTABLE the relay operates only while pressing transmitter’s push-button.
BISTABLE (one push-button) the device changes relay status cyclically always after
pressing the same push-button.
SWITCH ON the device switches on after pressing the push-button.
SWITCH OFF the device switches off after pressing the push-button.
TIME the device switches off according to the adjusted time (tp), but it may be switched
off before adjusted time nishes. Default settings - 15 seconds.
CAUTION! Adjusted time cannot be deleted.
Antenna
Optic signalling
of transmitters’ switching on
Programming push-button
Receiver’s socket
Power supply plug
Optic signalling of input voltage
Optic signalling
of transmitter’s operation
Push-buttons