Zebex A-52M User manual

Introduction
This Quick Start Guide applies to
2D
image
readers. The varied models
include handheld, hands-
free and
module.
All models are capable of
decoding 1D and 2D barcode
symbologies.
T
he scanner must be properly
powered before programming. Duri
ng
the programming mode, the scanner
will acknowledge a good and valid
reading with a short beep.
Otherwise,
the
scanner will remain silent for
invalid scanning.
The barcodes herein
only prepares
you ready to use the scanner. For
detailed programming ins
tructions and
safety notices please refer to the
complete Programming Guide
in the
manual CD.
If you can’t find the manual CD
,
please contact your distributor.
Laser Safety
The devices using lasers comply with
US 21CFR1040.10 and 1040.11
except for d
eviations pursuant to
Laser Notice No. 50 dated July 26,
2002 and IEC608525-1:+A1:1997+
A2:2001.
The laser classification is marked on
one of the labels on the devices.
Avoid long term staring into direct
laser light
to prevent damage to user
eyes.
Copyright © 2010 All rights reserved.
◎
◎◎
◎Default Factory Device Setting
Parameter Default
-Level (for handheld/hands-free scanner)
Trigger Mode -Presentation (for scan module)
Serial Host Type SSI Host
USB Device Type IBM Handheld USB
USB Country Keyboard Type North American
* Level Mode
A trigger event activates decode processing,
which continues until the trigger event ends, a
valid decode, or the decode session time-out is
reached.
* Presentation Mode
When the device detects an object in its field of
view it triggers and attempts to decode.
1. Using Serial Interface
1.1Serial Host
The default setting is SSI Host. If you use Serial Host, scan the
Enable Serial Host
(No Variant) barcode at right before use.
If you use Serial Host, your RS232 software, such as Windows HyperTerminal,
can receive data from the scanner.
Enable Serial Host (No Variant)
1.2 Character Return
Scan the <DATA> <SUFFIX 1> barcode at right to set up character return.
<DATA> <SUFFIX 1>
1.3 SSI Host
The default setting is SSI Host. If you use SSI host, your host device can transmit data
to software like Windows Notepad or Word. Follow the steps below to start using.
1. Connect the scanner serial cable to th
e host computer and connect a +5V power
adapter to the DC jack on the cable. The scanner would give a "Do Re Mi"
melody
when powered on.
2. Read the SSI Host barcode at right to set up interface.
(Skip this step if you are
using the default setting.)
3. Execute KeySimulator.exe in the Manual CD after the computer detects
the
scanner.
4. Choose a COM port number and click “Send Return” (Figure 1).
5.
Click “Start” to complete the setup procedure (Figure 1).
SSI Host
Figure 1

2. Using USB Interface
2.1 HID Keyboard Emulation
The default setting is IBM handheld USB. If you use HID keyboard emulation, scan
the
HID Keyboard Emulation barcode at right before use.
Scanner driver for HID keyboard is built-in for
Microsoft Windows version after
2000. But i
f you use Windows 98, you may need to download driver from
Microsoft website.
HID Keyboard Emulation
2.2 Character Return
Scan the <DATA> <SUFFIX 1> barcode at right to set up character return.
<DATA> <SUFFIX 1>
2.3 IBM Handheld USB
If you use IBM handheld USB, follow the steps below to start using the scanner.
1. Connect the scanner USB cable to the host computer.
2. Read the IBM Handheld USB barcode to set up interface
. (Skip this step if you
are in default setting.)
3. On the computer, check Human Interface De
vice to see if the computer
successfully detects the scanner as “HID-compliant device” (Figure 2).
Figure 2
4. Execute KeySimulator.exe in the Manual CD after the computer detects
the
scanner.
5. Tick USB ver1.0 and Send Return (Figure 3).
IBM Handheld USB
Figure 3
P/N: 593-9AZ00E-006