ZENEC Z-E2050 User manual

Z-E2050
DEVICE INSTALLATION MANUAL
EN

2
Model Model Version Model Year
VW Amarok 2H as of 2010
VW Beetle Cabrio 5C 2011 – 2015
VW Beetle Coupé 5C 2011 – 2015
VW Caddy 2K/2C 2003 – 2013
VW CC 35 2008 – 2014
VW EOS 1F 2006 – 2013
VW Golf V 1K 2003 – 2008
VW Golf V Variant 1K 2007 – 2009
VW Golf VI 5K 2008 – 2012
VW Golf VI Variant AJ 2009 – 2013
VW Golf Cabrio 51 2011 – 2013
VW Golf Plus 5M/52 2005 – 2013
VW Jetta VI 16 2005 – 2015
VW Jetta V / Bora 1K2 2005 – 2010
VW Passat 3C/36 2005 – 2014
VW Passat Alltrack 36 2012 – 2014
VW Passat CC 35 2008 – 2012
VW Passat Variant 3C/36 2005 – 2014
VW Polo 6R 2010 – 2014
VW Scirocco III 13 2008 – 2014
VW Sharan 7N 2010 – 2013
VW Tiguan 5N 2007 – 2013
VW Touran 1T 2003 – 2013
VW T5 7E /7J 2010 – 2015
SEAT Alhambra 71 2010 – 2013
SEAT Altea 5P 2004 – 2014
SEAT Altea Freetrack 5P 2007 – 2009
SEAT Altea XL 5P 2006 – 2014
SEAT Leon 1P 2005 – 2012
SEAT Toledo 5P 2004 – 2009
SEAT Toledo KG 2012 – 2013
ŠKODA Octavia II 1Z 2009 – 2013
ŠKODA Octavia II Combi 1Z 2009 – 2013
ŠKODA Octavia II Scout 1Z 2009 – 2013
ŠKODA Rapid NH 2013 – 2015
ŠKODA Rapid Spaceback NH 2013 – 2015
ŠKODA Superb II 3T 2008 – 2014
ŠKODA Superb II Combi 3T 2008 – 2014
ŠKODA Yeti 5L 2009 – 2014
COMPATIBILITY LIST
Radio
QUADLOCK II
Navigation

3
● The installation of the ZENEC system should be carried out by an authorized installer. Specic
knowledge and tools are required to do the installation. Incorrect installation can cause damage to the
vehicle and the ZENEC system.
●Correct functioning can only be guaranteed when you use the ZENEC original accessories included
in the kit or those optionally available. The ZENEC system and the original accessories must under no
circumstances be modied or altered in any way. Inappropriate actions can cause damage to the
vehicle and the ZENEC system.
●Torx screwdriver T25
●Release tool made of plastic
●Insulating tape
●The target vehicle must factory congured with one of the OE radio or navigation systems, listed
on the previous page. The ZENEC system is not compatible with vehicles, which are equipped with a
hybrid or electro drive ex factory.
●This device installation manual applies to vehicle platforms appearing in the compatibility list on the
previous page, and in a condition as offered by the respective vehicle manufacturer. Other differing
congurations and installations may result in complications and malfunctions.
●The ZENEC system is equipped with an integrated DAB+ receiver. To make use of this you will need
a suitable DAB antenna (not included in kit) that must be connected to the ZENEC system.
●If the target vehicle is already equipped with an original DAB antenna, it is still possible to use it in
combination with the ZENEC system. Please use the DAB antenna connector (No. 6), which is part of
the kit, for connection.
●The Z-E2050 comes with an adaptor interface, which ts to the double FM antenna plug from the
vehicle. If this solution is not sufcient, e.g. the FM radio reception is deemed to be poor, the
ZE-NC-ANT3 phantom power adaptor which is separately available, may help to improve FM signal
level.
●Software updates to the ZENEC system are installed with a USB memory device. Therefore when
tting the system make sure that the USB connection of the ZENEC system will still be accessible
later (installation of USB extension cable or USB hub).
●If you have questions or problems relating to the ZENEC system, please contact the dealer from
whom you purchased it.
●Additional questions about the compatibility could be answered by using the ZENEC online
congurator:
www.zenec.com/congurator
TOOLS REQUIRED
No. Article Qty
1 ZENEC system 1
2 GPS antenna 1
3 Double-sided adhesive pad 1
4 Main connection cable Quadlock II 1
THE KIT INCLUDES
5CAN bus interface 1
6DAB antenna adapter (Fakra – SMB) 1
7USB extension cable 1
824-pin connection cable (4.2, Cam, Mic) 1
9FM antenna adapter (Single to twin Fakra) 1
●ZENEC ZE-NC-ANT3 (antenna interface)
●DAB antenna with SMB plug
(e.g. Z-EACC-DAB1 or Z-EACC-DAB2)
●External microphone (N-ZENC-MIC)
ADDITIONAL MOUNTING ACCESSORIES
CAUTION
NOTE

1
4
4
3
2
EXAMPLE OF INSTALLATION GOLF VI
REMOVAL WORK AND PREPARATION:
3. Unscrew and remove the four Torx Screws
(T25) of the original device.
1. Gently lift the trim frame starting on the right
side of OE device. For successful completion of
this step, using a release tool made of plastic is
mandatory.
2. Run the prying tool anticlockwise around the
trim frame, to release it from the console. The
trim frame should come off of the console
completely.
4. Remove the original device by pulling it out of
the radio slot. Detach all the cables from its
backside.
1. Remove the ignition key and keep it outside the car until the installation is finished.
2. Please wait for about 10 minutes until the CAN bus system is completely shut down, before you start
with the uninstallation of the original device.
3. Now you can start with the uninstallation of the original device.
4. Please switch on the ignition only, once all installation steps are completed and the ZENEC system
is firmly mounted.
NOTE

5
9
8
INSTALLATION: 5. (No picture)
Install the GPS antenna (No. 2) in a suitable
position, making sure that the GPS reception is
not adversely affected by unwanted shielding
of metallic vehicle parts (thermal insulation
glazing, etc.). Then route the connection cable
into the radio bay.
6. (No picture)
If you have purchased the optional external
Bluetooth microphone (N-ZENC-MIC), install
it now and route the connection cable into
the radio bay. Depending on your preference,
and whether you select an internal or external
microphone, the microphone source for
Bluetooth mode must be set accordingly in the
unit menu.
7. (No picture)
Route the USB extension cable (No. 7) from the
radio bay to your preferred position.
8. Connect one of the main connection cables
(No. 4) of the ZENEC system (No. 1) to the
Quadlock connector of the car and close its
locking mechanism. Following this, connect the
CAN bus interface (No. 5) to the main connec-
tion cable.
9. Before installing the ZENEC system (No. 1)
remove the two transport securing screws.

6
10
11
12
COMMISSIONING
Finally carry out a general functional test and perform the basic and car specific settings (AC, OPS etc.).
Also ensure that no fault warnings appear on the vehicle side.
12. Press the trim frame back on to make the
installation complete.
●Make sure that all connectors at the rear of the ZENEC system have sufficient room and are not bent.
● Connectors without a retaining mechanism must be additionally secured with insulating tape.
11. Neatly arrange the wires to the side, making
room for the ZENEC system. Carefully slide it
into the radio slot and fix it in place, using the
four original Torx screws.
10. Connect all the cables to the ZENEC system
(No. 1): those previously run in the radio slot,
and the original antenna cables.
NOTE

Technical modifications excepted. No liability granted for printing errors.
© Copyright 2018 · RevB / copy deadline: Q1-2018 · English
ZENEC · Bohrturmweg 1 · CH-5330 Bad Zurzach · Schweiz/Switzerland · Mail: [e-mail] · www.zenec.com
CONNECTION DIAGRAM
C1 Rear Monitor Out
C2 N.A.
C3 Camera IN
C4 Video IN
C5 AUX IN L
C6 AUX IN R
C7 Line Out Rear L
C8 Line Out Rear R
C9 Line Out Front L
C10 Line Out Front R
C11 Line Out Sub Woofer
C12 Line Out Sub Woofer
C13 MIC
C14 N.A.
C15 IR/IN
C16 GND
C17 N.A.
C18 Camera +12V (max 300mA)
C19 N.A.
C20 N.A.
C21 N.A.
C22 N.A.
C23 N.A.
C24 N.A.
B1 Speaker Rear Right (+)
B2 Speaker Front Right (+)
B3 Speaker Front Left (+)
B4 Speaker Rear Left (+)
B5 Speaker Rear Right (-)
B6 Speaker Front Right (-)
B7 Speaker Front Left (-)
B8 Speaker Rear Left (-)
B9 CAN High
B10 CAN Low
B12 GND
B15 B+
B17 AUX-L
B18 AUX-GND
B29 AUX-R
BQUADLOCK II
CONNECTOR
B9
B10
B18
B17
B29
A20 PIN CONNECTOR
(DEVICE BACKSIDE)
A1
A11
A10
A20
A11 N.A.
A12 P. ANT +12V** (Antenna)
A13 P. CNTR +12V** (Amplifier)
A14 Parking
A15 KL 31 / Power GND
A16 KL 30 / Permanent +12V PWR
A17 Speaker Rear Right (-)
A18 Speaker Rear Right (+)
A19 Speaker Front Right (-)
A20 Speaker Front Right (+)
A1 N.A.
A2 Reverse
A3 KL 15 / Switched +12V PWR
A4 Illumination
A5 Analog Wheel KEY 2
A6 Analog Wheel KEY 1
A7 Speaker Rear Left (-)
A8 Speaker Rear Left (+)
A9 Speaker Front Left (-)
A10 Speaker Front Left (+)
** 300mA max current
C
C24 C2
C23 C1
24 PIN CONNECTOR
AC
DAB
USB 1
USB 2
HDMI
B
CAN Box
Rear Monitor Out Camera IN
P.CONT (max 300mA) P.ANT (max 300mA)
Video IN Aux IN L Aux IN R Line Out Rear L Line Out Rear R Line Out Front L Line Out Front R Line Out Woofer Line Out Woofer
MIC
IR / IN GND Camera +12V (max 300mA)
P. A N T
GND
GND
P. A N T
Aux Out L Aux Out R
Z-E2050
DAB HDMI
USB 2
USB1:
• Apple MFI
• USB Media Playback, -Smartlink Direct, -Software Updates
USB2:
• Apple MFI
• USB Media Playback, -Smartlink Direct, -Software Updates
A
GPS
UKW/
FM
USB 1
C