Zeversolar Zeverlution S User manual

Grid
Zeverlution
SEvershine TL Eversol TL
Code
SetupGuide- Single Phase Inverter

Grid_Code_1_Phase_Inv_Rev1_20160510 1
Single Phase Inverter
Grid Code Setup Guide
Zeversolar Contact Details
Karlos Silva – Technical Sales Manager – Europe
Address: Luxemburger Str.59, 50674, Cologne, Germany
Email: [e-mail]
Phone: [phone]
Revision
Date
Summary
Author
1
04-05-2016
Release
KS

Grid_Code_1_Phase_Inv_Rev1_20160510 2
Table of Contents
1Single Phase Inverter – Grid Code Set-Up................................................................................................................... 3
1.1 Introduction...................................................................................................................................................................... 3
1.2 Assumed Knowledge................................................................................................................................................... 3
1.3 IMPORTANT – CHECK GRID CODE SETTING DURING COMMISSIONING!............................................... 3
1.4 When is Changing the Grid Code Required........................................................................................................ 4
1.5 Hardware Requirements............................................................................................................................................ 4
1.6 Grid Code Set-Up........................................................................................................................................................... 4
1.7 Zeversolar Contact Details....................................................................................................................................... 5

Grid_Code_1_Phase_Inv_Rev1_20160510 3
1Single Phase Inverter – Grid Code Set-Up
1.1 Introduction
This standard operating procedure (SOP) details the steps that are required to change the default grid
code setting of a Zeversolar single phase inverter.
1.2 Assumed Knowledge
This guide assumes the following:
A Zeversolar single phase inverter has been installed;
The installation manual has been read and fully understood.
1.3 IMPORTANT – CHECK GRID CODE SETTING DURING COMMISSIONING!
The grid code setting should be checked during the commissioning of a PV plant. It is essential to
ensure that the correct grid code/safety setting has been selected for the relevant region. Each
Zeversolar inverter is set to a default grid code which is based on the serial number suffix that can
be found on the label affixed to the inverter and its packaging, see Figure 1 below.
Figure 1 - Serial Number with UK Suffix
Inverters shipped to Europe have three distinct suffixes and as such the default grid code is set
accordingly, please see Table 1.
S/N Suffix
Default Grid Code
DE
VDE-AR-N-4105
UK
G83/2 or G59/3
NL
NEN 50438
Table 1 - Default Grid Code Settings
Therefore it is necessary to check the serial number suffix and ensure that the correct grid code is
set. For example, an inverter being installed in the UK may have the DE suffix, in this case the inverter
grid code should be changed from the “VDE-AR-N-4105” grid code to the relevant UK grid code “G83/2
or G59/3.”

Grid_Code_1_Phase_Inv_Rev1_20160510 4
1.4 When is Changing the Grid Code Required
As mentioned above it is necessary to change the grid code if the inverter is not installed in the region
to which the default grid code is set to. The grid code should also be changed if the inverter is installed
in the following countries:-
Austria, Belgium, France, Greece, Northern Ireland, Poland, Republic of Ireland, Switzerland,
Turkey.
Please note: please refer to the Certificate Overview available from the Zeversolar website to
determine in which regions the Zeversolar inverters are certified.
1.5 Hardware Requirements
Eversol TL – please note that this series of inverter has been discontinued;
Zeverlution S;
Evershine TL.
1.6 Grid Code Set-Up
It is necessary to ensure that the inverter has been isolated from the AC supply. To change the grid
code please follow the steps outlined in Table 2.
Steps
Images
1. Navigate to the “Inverter Model” screen
by pressing the control button on front
panel.
2. When then “Inverter Model” screen is
displayed, press and hold the control
button for approximately 10 seconds.
3. The default grid code will now be shown
on the LCD. The image to the right shows
an inverter with the German default grid
code setting.
4. To change the grid code setting, press
the control button repeatedly until the
desired grid code is displayed on the LCD
As an example the “GB G83/2” is
displayed. To confirm the grid code
simply release the control button and
wait until the “Normal” screen is
displayed.
Table 2 - Firmware Version Check

Grid_Code_1_Phase_Inv_Rev1_20160510 5
1.7 Zeversolar Contact Details
Karlos Silva – Technical Sales Manager – Europe
Address: Luxemburger Str.59, 50674, Cologne, Germany
Email: [e-mail]
Phone: [phone]