Zibro Laser 56 User manual

Laser 56
3
27
51
75
98
122
MANUEL D’UTILISATION
GEBRAUCHSANWEISUNG
BRUGSANVISNING
OPERATING INSTRUCTIONS
ISTRUZIONI D’USO
GEBRUIKSAANWIJZING
3
2
6
4
>
1

75
4OPERATING INSTRUCTIONS
Dear Sir, Madam,
Congratulations with your purchase of the Zibro, the number one brand among
movable heaters. You have purchased a first-class quality product, which will
serve you for many years to come. This, of course, provided you use the heater
correctly. Please read these Directions for Use first, to ensure maximum lifetime
for your Zibro.
Your heater comes with a 24-month manufacturer’s warranty on all defects in
material or workmanship.
Wewish you much warmth and comfort with your Zibro.
Yours sincerely,
PVG International B.V.
Customer Service Department
1READ THE DIRECTIONS FOR USE FIRST.
2INCASE OF ANY DOUBT, CONTACT YOUR ZIBRO DEALER.

76
WHAT YOU NEED TO KNOW IN ADVANCE
THE RIGHT FUEL
Only use Class C1 paraffin fuel in accordance with BS2869: Part 2, or equivalent. Your Zibro heater has been
designed for use with high-quality water-free pure paraffin oil, such as Zibro Extra or Zibro Kristal. Only
fuels of this kind will ensure clean and proper burning. Lower quality fuel may result in:
Eincreased possibility of malfunctioning
Eincomplete burning
Ereduced heater lifetime
Esmoke and/or smells
Edeposits on the grid or mantle
Using the right fuel is therefore essential for safe, efficient, and comfortable use of your heater.
Always refer to your local Zibro dealer for the right fuel for your heater.
TIPS FOR SAFE USE
1Make surethat children are always aware of the presence of a burning heater.
2Position the front of the heater at a distance of minimum 1.5 metres from walls, curtains, and furniture.
3Do not use the heater in dusty rooms. You will not have optimum burning in such rooms. Do not use the
heater in the immediate surrounding of a bath, a shower or a swimming pool.
4Switch off the heater, before you leave or go sleeping. Unplug the heater as well, when you go away for
alonger period of time (e.g. holidays).
5Store and move fuel only in suitable tanks and jerrycans.
6Make surethat the fuel is not exposed to heat or extreme temperature changes. Always store the fuel in
acool, dry and dark place (sunlight will affect the quality).
7Never use the heater in places where harmful gasses or fumes may be present (e.g. exhaust gasses or
paint fumes).
8Beware that the grid of the heater becomes hot. If the appliance is covered there is a risk of fire.
• The first time you ignite your heater it will smell like ’new’ for a short time.
• Store your fuel in a cool and dark place.
• Fuel has a limited shelf life. Start every heating season with renewed fuel.
• The right quality of fuel will be assured, when you use ZibroExtra or ZibroKristal for
your heater.
• If you change to another brand and/or type of parrafin oil, you must first finish up all
the remaining fuel in the heater.

1. Introduction
This chapter contains all the relevant information,
specifically:
• Installation specifications
• List of installation tools
• Basic requirements for the installation of the fuel
tank
• Instructions for the installation of the Laser System
The heater can be installed at any location, on condi-
tion that thereis full compliance with electrical, fuel
and emission regulations.
Before you start installing the heating system (possibly
including electrical wiring and fuel supply equipment),
check the local building and fire safety regulations. The
requirements stipulated in these regulations must be
respected in order to guarantee a legally approved
installation and correct operation.
The heater was designed to be used to a
maximum altitude of 1000m above sea level.
Contact your dealer for the necessary
adjustments if you wish to use it at a higher
altitude.
2. Moving the heater
In addition to the space required for the heater, extra
room must be kept free for air circulation. We recom-
mend that you store fuel elsewhere. The Laser System
can be placed on any type of flooring (including fitted
carpets or other flammable materials) and operate
safely, unless fuel or fire safety regulations specify oth-
erwise. Check the gaps in the manner stipulated in the
instructions in the manual.
Recommended tool kit
1. Crosshead screwdriver
2. Steel tape measure
3. Felt-tip pen or pencil
4. Cement for exterior use
5. Electric drill (clockwise and anti-clockwise
recommended)
6. Hole cutting saw, jig saw or other tools suitable for
sawing a hole of 70~80 mm for the exhaust pipe
7. Long drill
8. Standard screwdrivers
9. Adjustable spanners (various sizes)
10.Copper tube cutter
11.Reamer
12.Volt, Ohmmeter
13.Spirit level
14.Plumber’s tape for tube screw thread
15.Small range of self-tapping screws
16.Range of pliers (pin tongs, needle nose pliers,
cutting pliers, locking pliers)
17.Insulated screwdriver
18.Protective material for your floor
19.Container for fuel exhaust pipe
3. The electrical supply system
The electrical system must be protected from overloads
by an at least 5-Amperefuse or contact breaker.
Some installations (such as for use in mobile
homes) must be fitted with a permanent
connection to the household power circuits.
This must be done by a recognised
electrician.
4. Fuel tank
Heater fuel (exclusively water-free, pure paraffin oil) in
200/1000 litrestorage tanks located outside. If large
tanks areused, a pressure regulator with a max. of 2.5
PSI (± 0.17 bar) must be fitted at the inlet on the
heater.This must be carried out in strict adherence to
all local standards and/or building regulations.
Chapter 1, INSTALLATION
77
☞
☞

5. Wiring for the room temperature sensor
Atemperature sensor that can be fitted to a wall mea-
sures the room temperature in order to automatically
regulate the heating. The standard sensor wire is
approximately 2.5 m long.
The sensor may not be placed in a draught,
direct sunlight or the warm air flowing out
of the heater. This may cause incorrect
temperature indications.
6. Unpacking
Save all packaging materials for possible future trans-
portation.
A) Remove the cardboard (drilling) template and the
user’s manual from the packaging.
B) Remove the base plate and the box with the
installation kit from the packaging.
C) Remove the heater from the packaging.
D) Remove the plastic bag covering the heater.
E) Remove the plastic bag containing the parts.
F) Remove the exhaust pipe from the bottom of the
box.
G) Check that all parts are present.
Only the standard feed and exhaust system
is supplied with the heater.
Chapter 1, INSTALLATION
78
Fig. 1-1: Gaps heater/exhaust pipe
Laser 56
Morethan 60 cm
Morethan 30 cm
Morethan 1,5 m
More than 30 cm
More than 10 cm
☞
☞

Chapter 1, INSTALLATION
79
Fig. 1-2 Gaps heater/exhaust pipe
Fig. 1-1 (continued) gaps heater/exhaust pipe
Flammable object
Not less than 60 cm
Flammable object
Non-flamma-
ble object
45°C
Not less than 30 cm
Exhaust pipe
Not less than 60 cm
Not less than 20 cm
Not less
than 45 cm
Not less
than 45 cm
Frontal obstruction
45 cm or more
50 cm or more
Snow-covered surface or ground
Important: The gap with the ground must be enlarged in areas
subject to heavy snowfall. Important:Awindbreaker may be necessary in open areas that
are subjected to strong winds.
Extension tube of
max. 2.5 metres Must be higher
Snow
Strong wind
Distance from
exhaust pipe to
windbreaker mini-
mum 45 cm
Not less
than
45 cm Windbreaker

☞
After using the installation template as a guide for the
drilling of the hole for the exhaust pipe, the Laser can
be installed normally, according to the procedure in the
illustration.
If the template is lost or the heater has to be moved,
these are the dimensions and locations of the holes for
the fuel pipe and exhaust pipe.
Do not remove any components from the
heater. Always contact your dealer if repairs
are required.
If the electricity cable is damaged, this may
only be replaced with type H05 VV-F and by
arecognised installer.
Chapter 1, INSTALLATION
80
Laser 56
Back of the heater
Fuel inlet
(82 mm)
(31 mm)
Centre of the
feed-through
component
(305 mm)
(127 mm)
Floor
Fig. 1-3 Template

Chapter 1, INSTALLATION
81
Standard installation parts
The following list of standard installation parts is sup-
plied with your heater. It may be necessary to order
extra parts from your Zibro dealer if other installation
methods are required.
Base plate (1) Wall hooks (2 set)
Pipe holder (2) Pipe lock (1)
Exhaust pipe (1) Exhaust Extension pipe (S) (1)

Chapter 1, INSTALLATION
82
Right-angled exhaust pipe bend (1) Discharge chute (1)
Right-angled air hose (2) Flexible air hose (1)
Hose clip (2)

Chapter 1, INSTALLATION
83
1. For the standard installation, use the template sup-
plied to position the hole for the exhaust pipe correct-
ly. Use cellotape or small nails to attach the template to
the desired position on the wall (see Fig. 4).
Fig. 4
Tape
Comment: The heater must be installed on a strong
and stable floor.The floor must be flat and level. If this
is not the case, the heater can be levelled by means of
adjustable legs. This can be checked with the plumb
line.
2. Drill the hole for the exhaust pipe. Use a hole saw
with a diameter of 70~80 mm (see Fig. 5). The opening
on the interior side of the wall must be a little higher
than the opening on the outside in order to create a
slight gradient in the feed-through and exhaust pipe
after installation (approximately 2º) (see Fig. 6). This
ensures that condensed water in the exhaust pipe flows
to the outside and prevents the penetration of rainwa-
ter and snow after installation.
Fig. 5 Fig. 6
2°