Zip HydroTap G4 Boiling, chilled sparkling... User manual

802005UK - Residential (Boiling),chilled and sparkling installation instructions - Aug 2015 - v2.01 Page 1 of 40
Zip HydroTap G4
Installation instructions
®
Chilled sparkling model
Command-CentreTM.Boiling, chilled sparkling model
Command-CentreTM.
Affix model number label
here
802005UK
Filtered boiling, chilled and sparkling drinking water for residential kitchens.

Page 2 of 40 802005UK - Residential (Boiling),chilled and sparkling installation instructions - Aug 2015 - v2.01
Tap options
The G4 series offers a range of interchangeable taps to suit the customer's needs
Classic HydroTap®G4 range
Arc / Cube range
Elite range
All-in-One range
Mixer range
These standalone taps are directly compatible with
the G4 Command-CentreTM.
The All-in-One tap may be used as alternatives to
any of the above combinations.
The mixer tap range may be used in conjunction with
any of the above to provide mixed hot and cold water
for sanitary use.

802005UK - Residential (Boiling),chilled and sparkling installation instructions - Aug 2015 - v2.01 Page 3 of 40
HydroTap®G4 specifications
Installation check list .................................................................................................................... 4
General product features ............................................................................................................. 5
Important safety instructions ........................................................................................................ 6
Warnings...................................................................................................................................... 7
Major components and accessories............................................................................................. 8
Technical specification................................................................................................................. 9
Before installation and site requirements..................................................................................... 10
Installation instructions
Step 1 - Measure and cut all the tap holes before fitting the taps.
Section 1 - Tap installation.
1.1 - HydroTap®G4 Classic and Elite taps installation .................................................... 11-13
1.6 - HydroTap®G4 Arc / Cube taps installation .............................................................. 14-15
1.10 - Mixer tap installation .............................................................................................. 16
1.12 - All-in-One tap ‘Mains’ installation........................................................................... 17-18
1.16- All-in-One tap ‘Vented’ installation........................................................................... 19-20
Step 2 - Check for adequate ventilation.
Section 2 - Ventilation.
2.1 - Ventilation on all models........................................................................................... 21
Step 3 - Install the booster (if required)
Section 3 - Booster installation
3.1- Product details and installation procedure................................................................. 22-24
Step 4 - Mount the external filter / softener (if required)
3.5 Mounting the filter head and cartridge installation...................................................... 25
Step 5 - Fit the CO2gas cylinder
Section 4 - CO2cylinder and regulator
4.1 - Connect, secure and test the CO2cylinder............................................................... 26-27
Step 6 - Install the Command-CentreTM.
Section 5 - Command-CentreTM installation
5.1- Check the external bypass valve setting & Mains water supply hose........................ 28
5.3- Boiling, chilled and sparkling HydroTap®G4 models.................................................. 29
5.4- Boiling, chilled and sparkling HydroTap®G4 and mixer tap combinations ................. 30
5.5- Boiling, chilled and sparkling All-in-One ‘Mains’ tap ................................................. 31
5.6- Boiling, chilled and sparkling All-in-One ‘Vented’ tap ................................................ 32
5.7- Chilled and sparkling HydroTap®G4 models.............................................................. 33
Step 7 Commission the HydroTap®G4
Section 6 - Commissioning
6.1- 6.2 Select language and CO2purge .......................................................................... 34
6.3- Filter flush .................................................................................................................. 34
6.4- Boiling calibration....................................................................................................... 35
6.5- 6.6 Booster................................................................................................................. 35
6.7- Safety sensor calibration............................................................................................ 36
Trouble shooting
Trouble shooting table.................................................................................................................. 37
End of life disposal....................................................................................................................... 37
Warranty....................................................................................................................................... 39
Contact details ............................................................................................................................. 40
Index

Page 4 of 40 802005UK - Residential (Boiling),chilled and sparkling installation instructions - Aug 2015 - v2.01
Before installation
• Read the instructions and check if there is adequate space to mount all of the components.
• Note Not all fittings are supplied with the appliance kit. Isolation valves are not supplied.
• Check the mains water pressure is within min / max requirements (see page 9).
• Check the water quality to determine if extra filtration will be required.
• Note This product must be fitted to a potable water supply.
• Check the appliance rating plate and ensure correct power is available for the appliance.
• Check the under counter cupboard floor has sufficient strength to support the Command-CentreTM
when full of water (see page 9 for weights).
Before commissioning
• Check the Command-CentreTM has been installed correctly.
• Check all plumbing fittings have been tightened.
• Ensure the outlet and vent pipes are positioned to drain correctly into a sink or font.
• Ensure there is adequate ventilation.
• Check all tubes and pipes from the Command-CentreTM to the tap have a constant rise and there
are no sags or kinks in the hoses.
• Check all electrical connections are correct and there are no loose wires.
Commission (see section 6)
• Flush the supply line before connecting.
• Turn on the gas and water and check for leaks.
• Purge the CO2.
• Flush the filters (this commences auto calibration for boiling models).
• Activate / enable the booster (if fitted).
• Calibrate the safety sensor (for boiling models).
• Where applicable, programme the Command-CentreTM to suit the customer’s requirements.
Installation checklist

802005UK - Residential (Boiling),chilled and sparkling installation instructions - Aug 2015 - v2.01 Page 5 of 40
General product features
HydroTap®G4 Command-CentresTM
Boiling, chilled and sparkling Chilled and sparkling
Thank you for purchasing a Zip HydroTap®G4. Please read and follow these instructions carefully to ensure
safe and trouble free operation. If help and advice is required, please call 0845 6 005 005 or 0345 6 005 005.
What is the Zip HydroTap®G4?
This Zip HydroTap®G4 is an electronically controlled, filtered, boiling, chilled and sparkling water, drinking
system for the kitchen. The Zip HydroTap®G4 Command-CentreTM is an under counter drinking water
appliance with a dispensing tap mounted on a sink or worktop, which has been designed for residential
applications. The Zip HydroTap®G4 Command-CentreTM utilises a conventional refrigerant compressor to chill
the water and for boiling, chilled and sparkling models an immersion heating element to boil the water and all
utilise a CO2gas cylinder to carbonate the chilled water. Depending on the model, the Command-CentreTM
will dispense boiling water (factory set to 98°C) and chilled and sparkling water (factory set to 3-5°C). The
HydroTap®G4 is NOT designed to be used for sanitary fixtures.
The Command-CentreTM is fitted with a tap mounted safety lock. In addition, there are various energy saving
options accessible via the main menu. Each Command-CentreTM providing boiling water is equipped with a
self-calibrating program which caters for altitude adjustment. The water filter and CO2cylinder are disposable
items which will require periodic replacement and are covered by a limited OEM (original equipment
manufacturer) warranty.
It is important that the installation be undertaken safely, correctly and completely, in order to utilise all
the benefits that the HydroTap®G4 can provide. Each unit can be ordered with the tap head assembly for
disabled use. The disabled levers are supplied with Braille caps for the visually impaired.

Page 6 of 40 802005UK - Residential (Boiling),chilled and sparkling installation instructions - Aug 2015 - v2.01
Important safety instructions
This manual contains important safety and installation instructions for the Zip HydroTap®G4.
Please read all warnings, installation requirements and installation instructions before installing any Zip
HydroTap®G4. This system must be installed in accordance with water supply byelaws,
current IEE regulations and relevant local authority byelaws.
Safety
This appliance is not intended for use by children under 8 years or persons (including
children under 8 years) with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or instruction concerning the use of the
appliance by a person responsible for their safety. Children should be supervised to ensure that they do not
play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
Refrigerant
The Zip HydroTap®G4 Command-CentreTM contains R134A refrigerant under pressure. Maintenance of the
refrigeration unit must be carried out by an accredited service provider or qualified refrigeration technician.
Qualifications
If the power cable is damaged it must be repaired only by a qualified technician. To avoid hazards, all
installation procedures must be carried out by a suitably qualified tradesperson. The power cable and power
outlet must be in a safe visible position for connection.
Venting
Sometimes steam and / or boiling water may discharge through a vent outlet on the tap. If the tap is not
installed using the font, ensure the tap body is located so the tap outlet safely dispenses into the sink bowl
area.
Lifting
Take care when lifting the Zip HydroTap®G4. The Command-CentreTM may exceed safe lifting limits. If
you feel this is beyond your personal capabilities, please seek assistance with the lift. The weight of the
Command-CentreTM is marked on the packaging. Do not lift the Command-CentreTM by the front cover or any
of its connections. Refer to the technical specification, see page 9, for the weight of the product.
Airflow
The Zip HydroTap®G4 operates within the ambient temperature range 5ºC - 35ºC. Proper air circulation
must be provided. The system will operate satisfactorily only if the recommended air gaps are provided. See
Section 2 'Ventilation', page 21, for correct installation to prevent overheating.
Altitude
Water boils at varying temperatures at different altitudes. The HydroTap®G4 adjusts for this during startup
calibration and will recalibrate itself on a regular basis.
Frost protection
If the HydroTap®G4 is located where the ambient air temperature could fall below 5ºC when the heater is
not in use, do not turn off the appliance electrically. This safeguard does not offer the same protection to the
connecting pipework and fittings.o
Positioning
It is important to ensure the Command-CentreTM is positioned in an accessible area close to the floor level.
The Command-CentreTM must have it’s base mounted in a horizontal position with all inlets and outlets facing
up. The tap must be located above the Command-CentreTM. See Section 1, Tap installation, pages 11 - 20.

802005UK - Residential (Boiling),chilled and sparkling installation instructions - Aug 2015 - v2.01 Page 7 of 40
CO2- Disposable cylinder
Compressed carbon dioxide, food grade
Cylinder specifications
• UN No. 1013 • Class 2.2
• Code ZT400 • Volume 2.2 litres
• Contents 1kg • Tare 1.745kg
• Test pressure 12 MPa (120 bar) • Boiling point -78.5°C
• Non flammable gas • Non toxic gas
• Std: EN12205 • Temp range -20°C to +65°C
Important safety instructions
WARNINGS
• The Zip HydroTap®G4 Command-CentreTM must be earthed. The
resistance of the earth connection from each exposed metal part must be
less than 1Ω.
• All installation and service work must be completed by trained and suitably
qualified tradespeople. Faulty operation due to unqualified persons working
on this product, or any other Zip product may void warranty coverage.
• As the installer, it is your responsibility to supply (if necessary) and install all
valves as required by local regulations and relevant standards.
• This Zip HydroTap®G4 Command-CentreTM is rated for 230V 50Hz AC
operation.
• Do not remove the cover of the appliance under any circumstances without
first isolating the appliance from the power supply.
• The Zip HydroTap®G4 Command-CentreTM must never be located near, or
cleaned with water jets.
• Do not expose the Zip HydroTap® G4 to the elements of nature.
• Due to the process of continuous improvement, Zip Heaters reserves the
right to change details mentioned in this manual, without notice.
CO2Cylinder warnings
• Pressurised container.
• Protect from sunlight.
• Contains gas under pressure, may explode if heated.
• Do not expose to temperatures exceeding 50˚C.
• Do not pierce or burn, even after use.
• Do not refill – non rechargeable.
• Ensure cylinder is empty before disposal.
• Do not expose to naked flame or any incandescent material.
• Keep out of reach of children.
• High concentration of gas may cause asphyxiation.
• Use only in ventilated areas.
• Store in an area no less than 38 cubic meters.
• Use only in an upright position.
• This bottle must be used with the approved pressure regulator.
• Avoid shock.
• Use according to MSDS. (Material safety data sheet).
Visit www.zipheaters.co.uk to ensure you have the latest copy.

Page 8 of 40 802005UK - Residential (Boiling),chilled and sparkling installation instructions - Aug 2015 - v2.01
Major components and accessories
Accessories Description
Booster
(inc. connection
hoses)
ZT011
Scale filter
installation kit
*ZT200G4
Filter not included.
Font kit
Classic & Elite
90915UK
Arc / Cube
93441UK
Replacement
internal 0.2 micron
filter
ZT402
Disabled lever kit
BCS SP91564
CS SP91565
(Classic HydroTap®)
4-in-1 upgrade**
SP91546 Classic
SP93413 Arc
SP93414 Cube
All-in-One
upgrade**
SP99413 (vented)
SP99414 (mains)
1 X
CO2gas cylinder
ZT400
Recommended
water block
HE45004
Parts supplied Description
Tap options
1 x
HydroTap®G4
Classic
Elite or Arc / Cube
1 x All-in-One
HydroTap®G4
Mains or Vented
1 x Mixer tap
Classic, Arc or Cube
Command-CentreTM and components
Vent kit
1 x outlet vent
1 x inlet vent
1 x
Command-CentreTM
with air and water
filters
1 x Mains water
connection hose
1 x Booster
inc. connection
hoses (supplied
dependant upon
configuration)
1 x Restrictaflow
valve and T-piece
(supplied with
vented mixer taps)
1 x User guide and
1 x Quick start
guide
1 x Installation
instruction
1 x
CO2gas cylinder
assembly
801599-HydroTap User Guide - Nov 2013 UK - V1.05 Page1of 20
ZIP HydroTap
User Guide
®
• Tap Operation...................(Pages 2-5)
• LCD Screen & Menu .......(Pages 6-18)
• Maintenance.................... (Pages 18-20)
• Date of Installation.........
Affix Model Number Label
Here
801599
BC160/125G4
BC240/175G4
BCH160/125G4
BCH240/175G4
AV160/125G4
AN160/125G4
AV240/175G4
AN240/175G4
801600 - Zip Quick Start Guide - October 2013 - V1.06
Parts Supplied Description Parts Supplied Description
1 off
Hydrotap Tap
and hoses
Duct kit
1x Air Duct
1 x Mounting
plate
1 off
Undersink Unit
with air and water-
filter
Vent kit
1 x Kickboard
louvre
1 x Door vent
louvre
1 x front vent grill
1 x Restrictaflow
valve and Tee
piece for Mixer
Taps
1 off
HydroTap
Booster heater
and hoses
(Supplied with
240/175 models)
1 off Mains water
connection hose
QUICK START GUIDE
Note: This quick start guide must be read in conjunction with
the main installation and user instructions
• Before proceeding, read the installation and user instructions
• Check all the components are present and correct.
• Check that you have all the necessary tools
•
Ensure the underbench can support the product weight when full of water,
(Check the specifications in the main book and allow an extra 5-8kg when full. )
Before installing ensure the following have been provided at
the installation site:
• Sufficient space in the cupboard to install all of the undersink units in accordance
with these Installation Instructions. Refer to technical specification for dimensions. If
required, make allowance for a booster heater. (Refer to the main book, for detailed
installation instructions).
• A potable water supply connection with isolating valve inside the cupboard within
reach of the flexible braided hose and positioned so that the connection point and the
stop cock will not be obstructed when all the undersink units are installed.
• For Zip HydroTap 160/125 &160/175 models, a 220-240Vac, 10A GPO will be
required. For Zip HydroTap 240/175 models, two 220-240Vac, 10A GPOs will be
required. (One GPO is for the Zip HydroTap and the other for the Booster heater).
NOTE: Check the cable lengths and outlet positions before proceeding.
• A potable cold water supply with a minimum working pressure of 172kPa and a
maximum working pressure of 700kPa connected via an isolation valve.
• For the mains pressure All-IN-ONE, both a hot and cold water supply will be required.
• The undersink appliances must be mounted in upright positions as shown in the
diagrams.
IMPORTANT! Do not proceed with the installation if these
requirements are not met.
STEP 1- Prepare and fit the Taps
Hole positioning: Position the tap such that it dispenses into
the sink bowl with ample clearance for a cup or tea pot. Alternatively,
the tap could be mounted away from the sink using a Zip Font, avail-
able as an accessory.
Apply a light smearing of silicon sealant
on the underside of the upper spacer to
ensure a watertight fi t.
For HydroTap and Mixer taps
cut a 35mm hole in the bench / sink top.
BENCH TOP
Ø35mm
HydroTap Tap
Mixer Tap 4-in-1
(If required)
NUT
LOWER RUBBER
WASHER
UPPER
RUBBER
WASHER
WASHER
BRAIDED
HOSE x 3
UPPER RUB-
BER WASHER
LOWER RUB-
BER WASHER
WASHER
NUT
White Hose
Ext. Mains
Blue band
Mixer IN
Red band
Mixer Out
O-RING
BASE
BLOCK
SPIDER
BASE
BLOCK
NUT USB
CABLE
ALL
THREAD
ROD
NOTE: feed each of
the tubes and elec-
trical cable evenly in
between the legs of
the BASE BLOCK
SPIDER.
All-In-One Tap (If required)
For AIO mains and vented Taps
Cut a 50mm hole in the bench / sink top.
NOTE: make sure the tap location will allow the nozzle to drain into the sink.
SINK TOP
50mm
ALL THREAD
ROD
STAINLESS
STEEL
WASHER
SPIDER
CLAMP
NUT
BLACK
PLASTIC
SPACER
NOTE: feed each of the three tubes and
electrical cable evenly in between the legs of
the SPIDER CLAMP when installing.
Fit the
STAINLESS STEEL
WASHER,
SPIDER CLAMP,
AND 6mm NUT.
6mm
NUT
SPIDER
CLAMP
Stainless
washer
Black plastic
spacer
35mm dia hole
Sink
O-RING SINK TOP
Fit the O-ring to the underside of the AIO tap
then pass all hoses through the 50mm hole.
Chiller
connection
BLUE
From Mixer OUT to Tap - Vented version only
Boiler
connection
RED
Blue ring on
RHS mains IN to
Mixer IN
White ring
on LHS to
Mains in
Tap
O ring Base
Clear tube to Vent
*ZT200G4 kit to fit filters
** Chrome finish part numbers are shown,
alternative finishes are available.

802005UK - Residential (Boiling),chilled and sparkling installation instructions - Aug 2015 - v2.01 Page 9 of 40
Technical specifications
* Add an extra 5 kg when full of water
Boost
(10A)
13A
sockets
required
Power
rating
(kW)
230V
Boost
rating
(kW)
230V
Unit Dimensions
W x D x H (mm)
with air duct
*Dry
weight
(kg)
Chilled, sparkling and filtered
no 1x13A 0.30 N/A 280 x 389 x 335 26kg
Boiling, chilled, sparkling and filtered, with booster
no 1x13A 1.70 N/A 280 x 470 x 335 30kg
Boiling, chilled, sparkling and filtered, with booster
yes 2x13A 1.70 2.20 280 x 470 x 335 30kg
Min / Max water supply pressure
HydroTaps and Mains All-in-One taps..............................0.25 MPa (2.5 bar) - 0.7 MPa (7 bar)
Mixer taps and Vented All-in-One taps.............................0.25 MPa (2.5 bar) - 0.7 MPa (7 bar)
Booster and scale filtration (in these systems).................0.25 MPa (2.5 bar) - 0.7 MPa (7 bar)
Boiling, chilled, sparkling and filtered.
Boiling Chilled and sparkling HydroTap®G4 range
Arc / Cube
Elite Classic
HydroTap®s
Mixer taps
Classic Arc Cube
All-in-One taps
Vented Mains
+
Boiling, chilled, sparkling and filtered together with
mixed hot & cold.
Boiling, chilled, sparkling and filtered together with
mixed hot & cold.
Chilled and sparkling HydroTap®G4 range
Chilled, sparkling and filtered.
Arc / Cube
Elite Classic
HydroTap®s

Page 10 of 40 802005UK - Residential (Boiling),chilled and sparkling installation instructions - Aug 2015 - v2.01
Before installation
Before installation ensure that the following have been
provided at the installation site
• Review of all the technical specifications.
• Ensure the under counter cupboard floor can support the product weight
when full of water (allow an extra 5kg when full).
• Sufficient space in the cupboard to install the Command-CentreTM and
other components in accordance with these installation instructions. See
technical specification, page 9 for dimensions. Make allowance for a
booster if required. See sections 3 to 4, pages 22 to 27 for installation
instructions.
• For Zip HydroTap®G4 boiling, chilled and sparkling models, 1 x 220-240V AC
13A socket will be required.
• For Zip HydroTap®G4 boiling, chilled and sparkling models,with booster 2 x
220-240V AC 13A sockets will be required. (One socket is for the Command-
CentreTM and the other for the booster).
• For Zip HydroTap®G4 Chilled and sparkling only models, 1 x 220-240V AC
13A socket will be required.
• The Command-CentreTM must installed in accordance with IEE
regulations.
Note Check all cable and hose lengths against inlet /outlet positions before
proceeding (see sections 3 to 4, pages 22 to 27 for general layout).
• A potable water supply connection with isolating valve inside the
cupboard within reach of the braided hoses and positioned so that the
connection point and the stop cock will not be obstructed when the
Command-CentreTM is installed.
• For the All-in-One 'Mains' models an external hot and cold water supply is
required.
• If an external filtration or water softening device is required, then it is
important to allow extra space for these items.
• A potable cold water supply with a minimum working pressure of:
(see page 9 min. / max. water supply pressure).
• If pressure is likely to exceed 0.7 MPa (7 bar), install a 0.35 MPa (3.5
bar) pressure limiting valve.
• The appliance must be placed with its base in a horizontal position.
IMPORTANT! Do not proceed with the installation if these requirements are
not met.

802005UK - Residential (Boiling),chilled and sparkling installation instructions - Aug 2015 - v2.01 Page 11 of 40
Section 1
HydroTap®G4 tap installation
Special tools required
In addition to normal tools, the following will be required.
For the HydroTap®G4 and mixer taps.
• 35mm diameter sheet metal hole punch for sinks (not supplied).
• 35mm diameter hole saw for worktops (not supplied).
• Nut runner tube spanner (supplied) for fixing the tap assembly.
For the All-in-One tap.
• 50mm diameter sheet metal hole punch for sinks (not supplied).
• 50mm diameter hole saw for worktops (not supplied).
• Nut runner tube spanner (supplied) for fixing tap assembly.
When installing a font, the following will be required
• Sheet metal punch or hole saw to suit surface being cut. Ø140m for Arc / Cube and
Ø108mm for Classic and Elite.
• Hole positioning
Position the tap such that it dispenses into the sink bowl with ample clearance for a cup or tea
pot. Alternatively, the tap could be mounted away from the sink using a Zip Font , available as
an accessory.(see Major components and accessories, page 8).
Tap positioning
Tap Recommended dispensing
distance (mm)
Elite 116
HydroTap®Classic 116
HydroTap®Arc/Cube 171 (-174 extended)
All-in-One 211
Mixer - Arc 231
Mixer - Classic 270
Mixer - Cube 310
BC HydroTap®G4 Classic
116
Note All-in-One and mixer taps have spouts that swivel.
All images are for illustrative purposes, to aid understanding of the system
configuration, and are not prescriptive of tap positioning.
• Ensure that the taps are mounted to minimise the risk of scalding by
accidentally dispensing boiling water while using the mixer.
• Ensure that the taps are mounted in a position that allows the water to
safely drain to waste throughout the complete positional range.

Page 12 of 40 802005UK - Residential (Boiling),chilled and sparkling installation instructions - Aug 2015 - v2.01
HydroTap®G4 - Tap installation
1.1
Apply a light smearing of silicon sealant on the underside of the spacer to ensure a
watertight fit.
1.2
All thread rod
Stainless steel
spacer
Spider
clamp
Nut
Black plastic
spacer
Cut a Ø35mm hole in the worktop / sink.
Note make sure the tap location will allow
the tap spout to drain into the sink.
(See page 29,30,33 for Command-CentreTM connections).
Ø35mm
Clearance envelope
535mm
min. 300mm
335mm

802005UK - Residential (Boiling),chilled and sparkling installation instructions - Aug 2015 - v2.01 Page 13 of 40
Installation instructions
Black
plastic spacer
1.3
Pass all the hoses, tubes and USB
cable through the 35mm hole.
1.4
Ø35mm hole
Note Feed each of the three tubes and USB
cable evenly in between the legs of the spider
clamp during installation.
Fit the
stainless steel
washer,
spider clamp,
and nut. Nut
Spider clamp
Stainless steel
washer
Incoming
water
1.5 Example Classic
HydroTap®installation
Note All plastic / silicon
tubes must be cut to size.
They must have a constant
fall back to the Command-
CentreTM

Page 14 of 40 802005UK - Residential (Boiling),chilled and sparkling installation instructions - Aug 2015 - v2.01
HydroTap®G4 Arc & Cube - tap installation
The HydroTap Arc/Cube has a spout that may be fixed in one of 6 angular positions (depending on the
position of the rotary control) and fixed in one of two height positions. The spout is fixed and does not swivel.
To reduce the risk of scalding, Position *A should not be selected with any of the boiling water units.
(See fig. 1.8).
1.6 Configuring the tap
• Remove the 2 x spout locating screws and lower the spout to expose the plastic spring clip.
Note The plastic spring clip has two internal dimples that may be positioned in the 6 upper or 6 lower,
pre drilled holes in the spout (see diagram below & figs. 1.7 & 1.8)
• To reposition the spout, gently spread the plastic spring clip to release the dimples from the spout
holes. When released, slide the clip on the spout so that it ends up between the two rows of holes.
• Rotate the plastic clip on the spout to orient the dimples, so they are in line with the newly selected
holes.
Note When determining which of the 6 holes are required for the new spout height and orientation,
check the new plastic clip position will clear the undercut and that the USB lead will not be pinched,
when assembled.
• Slide the plastic clip up/down to engage with the selected
holes, making sure the two dimples engage simultaneously
with the two selected holes.
Note The clip will not fit correctly if one dimple engages
before the other. Both dimples must engage at the same time.
• With the clip fitted to the newly selected holes,carefully
raise the spout (ensure the USB lead is a neat fit in the
undercut and is located between the open ends of the
clip) until the clip locating holes are in line with the spout
locating screws.
• Replace the 2 x locating screws.
• If mounting on an uneven surface, apply a light smearing
of silicon sealant on the o-rings to ensure a watertight fit.
(See fig. 1.9).
• Pass the assembly (ensuring upper o-ring, base ring and
lower o-ring are in place) through the Ø35mm hole and
position the tap so it discharges into the sink.
• Fit the lower rubber seal to the threaded extension.
• Secure the tap in position with the metal washer and nut.
Spout locating
screws (2)
Undercut
for loom
Lower locating
positions
Plastic
spring clip
Upper locating
positions
Clip locating
holes (2)
Dimples
Plastic
spring clip

802005UK - Residential (Boiling),chilled and sparkling installation instructions - Aug 2015 - v2.01 Page 15 of 40
Installation instructions
1.7 Height adjustment (xed position options)
50mm
Left hand control Right hand control
*A
B
C*A
B
C
1.8 Angular adjustment (xed position options)
Cut a Ø35mm hole in the work / sink top.
Note Make sure the tap location will allow
the tap spout to drain into the sink.
Ø35mm
Upper o-ring
Base Ring
Lower o-ring
(above work / sink top)
Lower rubber washer
Metal washer
Nut
(below work / sink top)
1.9 Mounting (See hole positioning, page 11 )
Note Use the Tube kit fitting instructions supplied with the tap kit to connect the tap head assembly to the
Command-CentreTM after the tap has been mounted securely.

Page 16 of 40 802005UK - Residential (Boiling),chilled and sparkling installation instructions - Aug 2015 - v2.01
1.10
Braided
hose x 3
Mixer tap installation
1.11
Nut
Lower rubber
washer
Upper rubber washer
Washer
Nut
Lower rubber
washer
Upper rubber washer
Washer
White marking - Ambient
mains supply
Blue marking - MIXER IN
on Command-CentreTM
Red marking - MIXER OUT
on Command-CentreTM
Note Make sure the tap location will allow the tap
spout to drain into the sink.
Note The mixer tap requires a Restrictaow valve,
supplied, to be tted in the cold water supply line,
from the isolation valve T-piece, to the mixer tap
(see page 30).
• Slide upper rubber washer in place on underside
of tap.
• Mount tap in position on Ø35mm hole.
• Slide lower rubber washer, metal washer then
tap nut over thread extension, then tighten the
tap nut to secure in place, do not over tighten.
• Attach the braided hoses (ensure the seals on
the end of the hoses are lubricated), do not over
tighten.
Cut a Ø35mm hole in the worktop / sink.
Ø35mm
Clearance
envelope
535mm
min. 300mm
(See page 30 for Command-CentreTM connections).
335mm

802005UK - Residential (Boiling),chilled and sparkling installation instructions - Aug 2015 - v2.01 Page 17 of 40
All-in-One tap
'Mains' installation
O-ring
Base block
spider
Base block nut
USB cable
Note Make sure the tap location will allow the tap
spout to drain into the sink.
1.13
1.12
Cut a Ø50mm hole in the worktop / sink.
Ø50mm
• Fit the o-ring to the underside of the AIO tap then
pass tubes, hoses and cable through the Ø50mm
hole.
• Feed each of the tubes and USB cable evenly in
between the legs of the base block spider.
• Fit the base block spider to the underside of the
All-in-One tap.
• Clamp in position using the base block nut.
Note All silicon tubes must be cut to size. They must have
a constant fall back to the Command-CentreTM.
(see page 31 for Command-CentreTM connections).
Clearance
envelope
535mm
min. 300mm
335mm

Page 18 of 40 802005UK - Residential (Boiling),chilled and sparkling installation instructions - Aug 2015 - v2.01
Installation instructions
Installing the All-in-One 'Mains' tap
1.15 All-in-One ‘Mains’ connections
• Connect the red and clear silicone tubes & USB
cable to the Command-CentreTM as shown.
• Connect the blue and white plastic pipe supplied
to the Y connector in place on the end of the blue
silicone tube, then connect to the Command-
CentreTM as shown.
• Working from inside the cupboard, attach the
braided hoses to the tube extensions (ensure the
seals on the end of the hoses are lubricated).
Check the correct position for hot and ambient
connections by matching the colours on the
braided hoses with the coloured markings on the
copper extension tubes. (See adjacent diagram).
• The braided hose with the blue markings must be
connected to the ambient mains supply.
• The braided hose with the red markings must be
connected to the hot mains supply.
• Do not over tighten the braided hoses.
• Ensure that all tubes and hoses are firmly
secured.
Clear silicone
tube - VENT on
Command-CentreTM
Red silicone tube -
BOILING OUT on
Command-CentreTM
Braided hose with blue
marking - ambient
domestic supply.
Braided hose
with red marking
- hot domestic
supply.
1.14 Base block spider markings and silicone tube positions (viewed from
underneath).
Blue marking Red marking
USB cable
Blue silicone tube
Red silicone tube
Clear silicone tube
(see page 31 for Command-CentreTM connections)
Braided hose with
blue marking
Braided hose with
red marking
Blue silicone tube
Y connector
blue plastic pipe to-
STILL OUT
white plastic pipe to-
SPARKLING OUT
on the
Command-CentreTM
RED
CLEAR
BRAIDED
POWER
CABLE
USB
MAINS
IN
MIXER
OUT
MIXER
IN
BOILING
OUT
BYPASS
OUT
VENT BYPASS
IN
BLUE
BRAIDED
CLEAR
CHILLED
OUT
SPARKLING
OUT
CO2
IN

802005UK - Residential (Boiling),chilled and sparkling installation instructions - Aug 2015 - v2.01 Page 19 of 40
All-in-One tap
'Vented' installation
1.16
O-ring
Base block
spider
Base block nut
USB cable
Note make sure the tap location will allow the tap
spout to drain into the sink.
1.17
Cut a Ø50mm hole in the worktop / sink.
Ø50mm
• Fit the o-ring to the underside of the AIO tap then pass
tubes, hoses and cable through the Ø50mm hole.
• Feed each of the tubes and electrical cable
evenly in between the legs of the base block
spider.
• Fit the base block spider to the underside of the
All-in-One tap.
• Clamp in position using the base block nut.
Note All silicon tubes must be cut to size. They must have
a constant fall back to the Command-CentreTM.
(see page 32 for Command-CentreTM connections)
Clearance
envelope
535mm
min. 300mm
335mm

Page 20 of 40 802005UK - Residential (Boiling),chilled and sparkling installation instructions - Aug 2015 - v2.01
Installation instructions
Installing the All-in-One ‘Vented’ tap (see page 32 for Command-CentreTM installation).
1.19 All-in-One ‘Vented’ connections.
• Connect the red and clear silicone tubes & USB
cable to the Command-CentreTM as shown.
• Connect the blue and white plastic pipe supplied
to the Y connector in place on the end of the blue
silicone tube, then connect to the Command-
CentreTM as shown.
• Working from inside the cupboard, attach the
braided hoses to the tube extensions (ensure the
seals on the end of the hoses are lubricated).
Check the correct position for mixer and ambient
connections by matching the colours on the
braided hoses with the coloured markings on the
extension tubes. (See adjacent diagram).
• Connect the braided hose with the blue marking to
the ‘MIXER IN’ on the Command-CentreTM.
• Connect the braided hose with the white marking
to the Restrictaflow.
• Connect the braided hose with the red marking
to the metal tube, with red marking then to the
‘MIXER OUT’ on the Command-CentreTM.
• Ensure that all tubes and
hoses are firmly secured.
Braided hose
connection to metal
tube - ‘MIXER
OUT’ on Command-
CentreTM.
Braided hose with
blue marking - to
MIXER IN’
on Command-
CentreTM
Clear silicone
tube - VENT on
Command-CentreTM
Braided hose with
white marking -
Restrictaflow on
ambient supply
Red silicone tube -
BOILING OUT on
Command-CentreTM
Blue silicone tube Y
connector
blue plastic pipe to-
STILL OUT
white plastic pipe to-
SPARKLING OUT
on the
Command-CentreTM
1.18 Base block spider markings and silicone tube positions (viewed from
underneath). White marking Blue marking
USB cable
Blue silicone tube
Red silicone tube
Clear silicone tube
Braided hose with
white marking
Braided hose with
blue marking
Braided hose with
red marking
HydroTap
Mixer
Connections
RED
CLEAR
BRAIDED
POWER
CABLE
USB
MAINS
IN
MIXER
OUT
MIXER
IN
BOILING
OUT
BYPASS
OUT
VENT BYPASS
IN
BLUE
BRAIDED
CLEAR
CHILLED
OUT
SPARKLING
OUT
CO2
IN
Booster
Connections