ZKTeco ProBG3000 Series User manual

Barrier Gate-ProBG3000 Series User Manual
P a g e | 1Copyright©2020 ZKTECO. CO., LTD. All rights reserved.
User Manual
Barrier Gate ProBG3000 Series
Date: November 2020
Doc Version: 1.3
English
Thank you for choosing our product. Please read the instructions carefully
before operation. Follow these instructions to ensure that the product is
functioning properly. The images shown in this manual are for illustrative
purposesonly.
For further details, please visit our c
www.zkteco.in.

Barrier Gate-ProBG3000 Series User Manual
P a g e | 2Copyright©2020 ZKTECO. CO., LTD. All rights reserved.
Table of Contents
1OVERVIEW ..............................................................................................................................................3
1.1 INTRODUCTION.............................................................................................................................................3
1.2 APPEARANCE................................................................................................................................................3
2PRODUCT INSTALLATION......................................................................................................................3
2.1 INSTALLATION PRECAUTIONS........................................................................................................................3
2.2 CABLE EMBEDDING.......................................................................................................................................4
2.3 INSTALLATION PROCEDURE...........................................................................................................................4
2.4 BOOM INSTALLATION....................................................................................................................................5
3SPRINGS TESTINGAND ADJUSTMENT..................................................................................................5
3.1 ADJUST THE POSITION OF BOOM...................................................................................................................6
3.2 ADJUST SPRING SETTING ..............................................................................................................................7
3.3 TESTING SPRING SETTING..............................................................................................................................7
4POWER CONNECTION ............................................................................................................................8
4.1 CONNECTION................................................................................................................................................8
4.2 TECHNICAL PARAMETERS............................................................................................................................10
5CONTROLBOARDPINDIAGRAM.........................................................................................................12
5.1 DIPSWITCH SETTINGS................................................................................................................................13
5.2 INPUT INTERFACE........................................................................................................................................14
5.3 OUTPUT INTERFACE INTRODUCTION............................................................................................................14
5.4 CONNECTING TO OTHER PARKING DEVICE...................................................................................................15
5.4.1 LicensePlatesRecognitionMachine(LPR)andControlPanel ....................................................................................15
5.4.2 ConnecttotheinBioController(UHFSystem)................................................................................................................16
5.4.3 LoopDetector........................................................................................................................................................................17
5.4.4 InfraredIntrusionDetector.................................................................................................................................................18
5.4.5 WhentheloopdetectorandtheIRareusedatthesametime....................................................................................20
5.4.6 WiringDiagramofthePush ButtonStation ...................................................................................................................21
6APPENDIX.............................................................................................................................................22
6.1 REMOTE CONTROLLER MATCHING AND DELETING INSTRUCTION..................................................................22
6.2 ANTI-COLLISION FUNCTION.........................................................................................................................22
6.3 PROBGREGULATION PARAMETERS.............................................................................................................23
6.4 PACKING ACCESSORIES LIST........................................................................................................................29

Barrier Gate-ProBG3000 Series User Manual
P a g e | 3Copyright©2020 ZKTECO. CO., LTD. All rights reserved.
1
1.1 Introduction
ProBG3000 Series are high performance and high-speed barrier gates. It has a high-performance
Servo Motor, simple and reliable transmission structure, high-temperature durable control panel,
humanized interactive appearance design, and anti-collision protection gate connector design.
1.2 Appearance
Fig. 1.1
2
2.1 Installation Precautions
•Before installing the parking barrier onthe ground, check for thesolidityof the base.
•If the ground is not firm and level,it is required to set a cement base before installation.
•Do not changethe wiringconnection inside the device when the power isin ON state.
•The GNDwire should beconnected to thecabinetfor protection.

Barrier Gate-ProBG3000 Series User Manual
P a g e | 4Copyright©2020 ZKTECO. CO., LTD. All rights reserved.
2.2 Cable Embedding
•thick protective sleeve and cable in advance.
•Connect the Routecablesthrough protective sleeves.
•Use a tool to open a cable tray on the ground.
Fig. 2.1
2.3 Installation Procedure
•Use a screw pad to markthe installationpositionof the cabinet.
•Drive four expansion boltsinto the bolt holes, as shown in Fig. 2.2.
•Install screw padsand use a spanner to tighten nuts,as shown in Fig.2.3.
Fig. 2.2
Fig. 2.3
Chassis
Control
Room
Screw Pad
Base concrete
AstandardpowerwireRVV3*1.0
Expansion
bolt 4-M12
Concrete Base
Ground
Cabinet
Ground
Screw pad
ExpansionBolt 4-M12
Ground
Ground
Thepowerwireiswrappedand
protectedusingthe wiresleeve
when laid out under the
ground (the strong current
should be separated from the
weak current).

Barrier Gate-ProBG3000 Series User Manual
P a g e | 5Copyright©2020 ZKTECO. CO., LTD. All rights reserved.
2.4 Boom Installation
•Place the boom into the boom tray head according to the holelocation.
•Use the spannerto clampthe round boom by screws, gasket, and screws nuts.
Fig. 2.4
3
•Basedonthestandardguidelinessetforthebooms,allofthebarriergatesare setupinthefactory
accordingly.
•The spring used in the mechanism is in a highly tense state. And all the adjustments of the barrier
must be carried only afterthe spring is in aloose state.
•Please check thestiffnessand placementof the boom after itis installed and operated for the first
time.
•Oncetheweightoftheboomisbalancedbythetensionappliedbythespring,thebarriergatecan
be operated properly. Therefore, if any change is applied (for example: after exerting excessive
force) to theboom it mustbe re-adjusted in accordance with the stepsmentioned below.

Barrier Gate-ProBG3000 Series User Manual
P a g e | 6Copyright©2020 ZKTECO. CO., LTD. All rights reserved.
3.1 Adjust the Position of Boom
To adjust the position of the boom, pleasetake the steps as below:
•Open the barriergate door and remove the cover.
•Loosen the two fastenscrews oftheDZ-1 ontheboom shaftwiththeM12's Allenwrenchso that
the boom can be repositioned by hand.
•Adjust the position of the boom (horizontal position, as shown in Fig. 3.1).
•Use the torque wrench to tighten the two fastening screws (72Nm).
Fig. 3.1
Unlocking ArmManually When Power is Off
When there is no power, the barrier gate maybe in a vertical or horizontal mechanical dead point
position. To unlock the arm manually at suh position of the boom, please follow the steps as
mentionedbelow.
1. Lifting the boom: Use the screwdriver to push the crank connected rod away from the dead
point position, lift thebarrier gate manually (Push to Unlock).
2. Dropping the boom: Use hand to pull the crank connected rod down to leave the dead point
position, dropthe barrier gate manually (Pullto Unlock).
Adjust the
horizontal screw

Barrier Gate-ProBG3000 Series User Manual
P a g e | 7Copyright©2020 ZKTECO. CO., LTD. All rights reserved.
3.2 Adjust Spring Setting
According to the length of the boom, assemble the compression spring. Also, tighten or loosen the
adjusted handleto maintain the boom stable at 45°. It is the best way to test spring strength.
Exceptions:
When there is a power failure, the barrier gates open automatically, and a greater spring force is
required.
3.3 Testing Spring Setting
1. Open the door of the barrier machine casewith a keyand remove the mounting plate.
2. Unplug the power cord.
3. Manually adjustthe boom to the position of about 45° and release hand.
4. If the boom is stable in this position and does not move, it indicates that the spring adjustment
is correct.
Push to unlock
Fig. 3.2
Pull to unlock
Fig. 3.3

Barrier Gate-ProBG3000 Series User Manual
P a g e | 8Copyright©2020 ZKTECO. CO., LTD. All rights reserved.
4
4.1 Connection
1. Connect the L and N to the air switchand PE to theground screws (Yellow-Green Line).
Only the provided power connection cables should beused to connect the main powersupply (the
internal power is already connected to thefactory).
After switching the power off, it is recommended to wait for at least 10 seconds before switching
the power on again otherwise it may damage the equipment.
2. To use AC power,please toggle the SW1 Switch toUSE AC POWER as shown in Fig.4.1.
WhenSW1istoggledtoUSEACPOWER,24VOUTPUT(CON2)canbeconnectedtoa24Vinfrared
detector or vehicle detector powersupply.
Fig. 4.1

Barrier Gate-ProBG3000 Series User Manual
P a g e | 9Copyright©2020 ZKTECO. CO., LTD. All rights reserved.
Fig. 4.2
3. Thisbarriergatecanalsobepoweredbya24Vbattery.Checkthebelowimagefortheconnection.
PuttheSW1ToggleSwitchtoUSEBATTERYtouseabatteryforpowersupplyinputandconfirm+/
-polaritywhen connecting the battery. Do not reverse the battery connection.
WhenSW1 is toggled to USEBATTERY, CON2 caninput 24V battery to power barrier gate.
Fig. 4.3

Barrier Gate-ProBG3000 Series User Manual
P a g e | 10 Copyright©2020 ZKTECO. CO., LTD. All rights reserved.
4.2 Technical Parameters
Model
Item
ProBG3030
L/R
ProBG3045
L/R
ProBG3060
L/R
ProBG3130
L/R
ProBG3230
L/R
ProBG3240
L/R
Boom
Length
3m
4.5m
6m
3m
3m
4m
Opening
Time
0.9s
2.5s
4.5s
1s
2s
3s
Boom Type
Straight/Telescopic Boom
90°
FoldingBoom
Fence Boom
Boomwith
LED
Optional
No
PowerConsumption
Max 100W
PowerSupply
24V DC, AC 100 to240V
Controller Frequency
50Hz to 60Hz
HousingMaterial
Powder Coated Steel
Packed Weight (No Boom)
60KG
Control Board Voltage
24V DC/max 300mA
Working Temp
-40° to +75°C
MeanCycles BetweenFailures(MCBF)
5 million times
DrivingUnit
Servo Motor
IP Rating
IP54

Barrier Gate-ProBG3000 Series User Manual
P a g e | 11 Copyright©2020 ZKTECO. CO., LTD. All rights reserved.
Interchangeable Boom Direction
Fig. 4.4

Barrier Gate-ProBG3000 Series User Manual
P a g e | 12 Copyright©2020 ZKTECO. CO., LTD. All rights reserved.
5
Fig. 5.1

Barrier Gate-ProBG3000 Series User Manual
P a g e | 13 Copyright©2020 ZKTECO. CO., LTD. All rights reserved.
5.1 DIP Switch Settings
Fig. 5.2
1. In DIP Switch 1, ON is for NC (Normally Closed) and OFF for NO (Normally Open). (Default mode,
do not modify)
2. In DIP Switch 2, ON is for automatic opening and OFF is for self-lockingwhen the power is off.
3. In DIP Switch 3, ON is for automatic stop and OFF is for automatic reversing when the boom
meets an external obstacle.
4. With DIP Switch 4, auto-closing speed can be adjusted. ON is for auto-closing speed of 1.3s
whereas OFFis for 0.9sfor the boom. (for the ProBG3030 model only)
5. The DIP Switch 5, 6, 7, 8 are used fordelaying automatic closingof the boom. The delaytime for
automatic closing of the boom can be set are 1s, 2s, 3s, 4s, 5s, 8s, 10s, 15s, 20s,25s, 30s, 35s, 40s,
50s, 60s asshown in Fig. 5.2.
6. If the boom cannot reach the vertical position due to any obstacle, the boom can be adjusted at
anangleof60°,70°,80°,and90°.AseparateDIPswitchisprovidedontheboardforthesame (1,
2 Switches).
7. Themaintenancemodeswitchisconvenientforpossiblerepairingandadjusting.(Defaultmode,
do not modify).

Barrier Gate-ProBG3000 Series User Manual
P a g e | 14 Copyright©2020 ZKTECO. CO., LTD. All rights reserved.
5.2 Input Interface
•The RS485 interface can connect with the computer to check the barrier gate state and alarm
information.
NOTE: Only theprofessional developers can operate,ask the sales staff toprovide RS485 Protocol.
•The parkinglot open/close control signal and remote control open/close signal are separate.
The arm opening has memory function, it remembers the number of pulse arm opening and
closesonce the counted number of cars passes by. (must be equippedwith a vehicledetector)
•"UP" and "DOWN" signal ports are available on themainboard.
•All input ports are in optoelectronic isolation. The input voltage range lies between DC5 to 24V.
•The vehicle detector signal input and infrared signal input uses the output COM, NC of the loop
detector. (normally the No.4 and No.11 are related to the detector)
NOTE: The barrier gate does not respond to the closing command when the coilis not connected.
5.3 Output Interface Introduction
•Line 1 BarrierGate Vertical PositionSignal, Relay Dry Node Signal (NC, C,NO).
•Line 1 BarrierGate Horizontal Position Signal, Relay DryNode Signal (NC, C,NO).
•Line 1 10A R&G Traffic Light Signal, Relay Dry Junction Signal (NC, C,NO), contacts can pass 10A
current.

Barrier Gate-ProBG3000 Series User Manual
P a g e | 15 Copyright©2020 ZKTECO. CO., LTD. All rights reserved.
5.4 Connecting to Other Parking Device
5.4.1 License Plates Recognition Machine (LPR) and Control Panel
The boom lifts automatically after LPR recognizes and verifies license plates (the function of the
Control Panel is similar toLPR). The wiring diagram isshown in Fig. 5.3.
Fig. 5.3

Barrier Gate-ProBG3000 Series User Manual
P a g e | 16 Copyright©2020 ZKTECO. CO., LTD. All rights reserved.
5.4.2 Connect to the inBio Controller (UHF System)
The UHF reader is connected to the controller, which then connects with the barrier gate control
board. The UHF tag authorizes the user's card number information in the software to the door of
the controller and then swipes the card to open thedoor automatically.
Fig. 5.4

Barrier Gate-ProBG3000 Series User Manual
P a g e | 17 Copyright©2020 ZKTECO. CO., LTD. All rights reserved.
5.4.3 Loop Detector
Loop detectors in the parking system consist of the loop, loop detector, and control board. The
loop is installed under the ground. When theloop detects a vehicle, the boom resists falling. After
the vehicle pass, the boom falls automatically.
The wiring diagram is shown in Fig. 5.5 (If only the Loop Detector is used, the
needs to be directly connected with +24V).
Fig. 5.5
Fig. 5.6

Barrier Gate-ProBG3000 Series User Manual
P a g e | 18 Copyright©2020 ZKTECO. CO., LTD. All rights reserved.
Coil Circumference
Coil Number
3m
According to the actual situation, ensure
that the inductance value is between 100
uH and 200uH.
3-6 m
5-6 turns
6-10m
4-5 turns
10-25 m
3 turns
25 m
2 turns
5.4.4 Infrared Intrusion Detector
IfacarorpersonexistsbetweenthetransmitterandreceiveroftheInfraredIntrusionDetector,the
boom will not fall. After the vehicle or person passes, the boom will fall automatically. The wiring
diagram is shown in Fig. 5.7.
Fig. 5.7

Barrier Gate-ProBG3000 Series User Manual
P a g e | 19 Copyright©2020 ZKTECO. CO., LTD. All rights reserved.
Installation of the Infrared Photocell Beam Detector
Fig. 5.8

Barrier Gate-ProBG3000 Series User Manual
P a g e | 20 Copyright©2020 ZKTECO. CO., LTD. All rights reserved.
5.4.5 When the loop detector and theIR are usedat the same time.
Check the wiring diagram (Fig. 5.9.) to view the connections when the loop detector and the IR
are used atthe same time.
Fig. 5.9