ZKTeco FaceKiosk-H13 User manual

Quick Start Guide
FaceKiosk-H13 Series
Version: 2.2
Due to regular upgrades of systems and products, ZKTeco could not guarantee exact consistency between the
actual product and the written information in this manual.

1. Components
Near Infrared Camera
Speaker
IC Card Reading Area
Near Infrared Fill Light
Fingerprint Scanner
/QR Code Scanner
13.3-inch High-definition Capacitive Touch Screen
Visible Light Camera
LED Fill Light
Near Infrared Fill Light
LED Fill Light
Speaker
FaceKiosk-H13A
1

2
Thermal Infrared Temperature
Measurement Module
Ticket Printer
QR Code Scanner
Near Infrared Camera
Speaker
IC Card Reading Area Fingerprint Scanner
13.3-inch High-definition
Capacitive Touch Screen
Visible Light Camera
Near Infrared Fill Light
LED Fill Light
Near Infrared Fill Light
Antenna
LED Fill Light
Speaker
Base
FaceKiosk-H13C/FaceKiosk-H13C[TD]
Note: Not all products have the function with , the real product shall prevail.

2. Product Interface
1
2
33
4
5
678
Connecting Terminal
SIM Card Slot
Video Out Port
USB Port
Network Port
Reset Button
Power Interface
USB Port
1
5
2
6
33 4
87
12V
GND
INWD0 INWD1
12V
GND
RXD
WD0
WD1
GND
TXD
GND
485A
485B
BUT
NO1
COM1
NC1
GND
SEN
NC
COM
NO
The terminals on the back of the FaceKiosk-H13 series are the same.
On the back of the device, there are five rows of slots, which are J1, J2, J3, J4, and J5 from left to
right. J1 is connected to the alarm, J2 is connected to the door, J3 is connected to the external
device, J4 is connected to the Wiegand input, and the J5 is the power output port reserved for a
Printer.
3

3. Installation Procedure
Before installation, connect the wire to the device and move it through the device’s lower aperture.
1
2
3Place the rear panel at an appropriate height from the ground. Drill the holes on the wall
and fix it.
Align the backplate to the screw holes on the back of the device.
Secure the plate with the screws (11 pcs) to the back of the unit.
FaceKiosk-H13A
4

4
5
Set the device at the desired position on the rear panel that is fixed on the wall.
Secure the Kiosk by assembling the device and the rear panel with the bottom screw.
5

2. Installation Procedure
Before installation, connect the wire to the device and move it through the device’s lower aperture.
1Take the device and the base from the box. Fix the device into the corresponding slot of
the base plate. Take the FaceKiosk-H13C[TD] as an example:
2Cautiously incline the device horizontally and assemble the device over the base with the
screws (8 pcs) from the bottom of the base.
FaceKiosk-H13C/FaceKiosk-H13C[TD]
6

3Place the device in the right position and remove the four screws that secure it to the base,
remove the metal cover.
4Drill holes with an electric drill, implant two screws into the ground to fix the device, then
cover back the metal cover, and finally tighten the four screws.
7

4. Door Sensor, Exit Button & Alarm Connection
5. Access Control Device Connection
GND
BUT
NO1
COM1
NC1
Door Sensor
ExitButton
+ -
+ -
FR107
-
ElectricLock
Power
SEN
COM
NC
Alarm
+
-
Power
NO
485 reader
RS232
Access Control
Device
485A
GND
TXD
RXD
WD0
485B
WD1
GND
12V
GND
INWD0 INWD1
Wiegand reader
8

6. 4G, Ethernet and WiFi Connection
4G Connection
Open the back cover of the device, insert the SIM card, and the device will be automatically configured
for 4G network.
LAN Connection
4G
Plug in the network cable. Then set the network parameters on the device.
Network cable
Wi-Fi Connection
Tap [System Settings] > [Network Settings] > [Wi-Fi Settings], and enable the Wireless network.
Note: The network parameters can be set in the Android interface, or in the software service. Refer to 10.
Software Basic Settings
9

7. Interface Introduction
The status of the connection between the device and the server, if the connection is not
successful, a red flag will be displayed.
Tap on to view the device information and the hardware module connection status.
Tap on to open the Main menu.
Tap on to open the QR Code self-registration.
Tap on to change the software language. The device supports English, Thai, Latin
Spanish, Russian, Japanese, Portuguese and Chinese.
10
Tap on to register visitors operation.
Tap on to check in or check out a visitor.

8. Operational Procedure
Visitor Self-registration Methods
The visitor can register by scanning the QR Code on the reception desk device or the QR Code on
the invitation E-mail sent by the system in advance.
Process Overview
Issues visitor information
to the access device
Forbids visitor access
after check-out
Visitor Arrival
Check-in
Grant Access
Check-out
Visitor Exit
Obtain Visitor Records
1) Register on the reception desk device. 2) Scan the QR Code to register via Mobile phone.
Note:
11

9. Clear the Data
Common Settings
Date and Time
Restore All the Settings
Exit
User Management
AD Settings
Record Search
Data Management
System Settings
System Infirmation
Tap on [System Settings] > [Common Settings] > [Exit]to exit the software.In the Android system
settings, find the two APKs in the application center, and click clear data to clear the cache.
Application
ZKBioLobby
Installed
Clear Data
ZKBioLobby
Do you want to clear data?
CANCEL OK
12

Settings on Device
10. Software Basic Settings
After completing the following simple steps, the device will be ready to use for visitor management.
Tap on [System Settings] > [Communication Settings] > [Ethernet Setting]to set the network
parameters.
Tap on [System Settings] > [Communication Settings] > [Software Server Setting]to set the server
address and server port,that is, the IP address and port number of the server after the software is
installed.
Communication Settings
Wifi Setting
Ethernet Setting
Software Server Setting
User Management
AD Settings
Record Search
Data Management
System Settings
System Infirmation
Set the Server details on device. E.g: http://192.168.161.12:8098
Server Address: 192.168.161.12
Communication Port: 8088
Server Port: 8098
Internet
13

Ethernet Setting
User Management
AD Settings
Record Search
Data Management
System Settings
System Infirmation
Enable Ethernet
DHCP
IP Address
Subnet Mask
Gateway Address
DNS
TCP Comm. Port
Manual
192.168.163.99
255.255.255.0
192.168.163.1
114.114.114.114
4370
Software Server Setting
User Management
AD Settings
Record Search
Data Management
System Settings
System Infirmation
Manual
Server Type
Server Address
Server Port
Communication Port
HTTPS
ZKBioSecurity
192.168.161.12
8098
8088
14

Add the device to the FaceKiosk Module of the software. Open the ZKBioSecurity software then
select [FaceKiosk] > [Device] > [Search] > [Add].
Search
Total Progress
IP Address
Device Type
Searched devices count:1
Number of devices added:1
The current systen communication port is 8088, please make sure the device is set correctly.
Search
IP Address Serial Number Operations
Serial Number
192.168.161.81 7575215100002 FaceKiosk Add
Close
FaceKiosk Device
Device Name
Device Serial Number
Device
Set Attendance By Area
Set Attendance By Person
Search Criteria None
Refresh Delete Search Control View/Get Clear Device Data
Device Serial Number Device Name Device Model IP Address Area Name Enabled Status Register Commands to be Excuted Personnel Quantity
Step 2Step 2
Step 1
Step 3
Step 4
Step 5
Set the device as an Entry device. Click [Visitor Module] > [Basic Management] > [Entry Place]
> [New].
Settings on ZKBioSecurity
Registration
Reservation
Basic Management
Parameters
Device Debugging
Print Settings
Visitor Levels
Host Levels
Visited Department Levels
Entry Place
Visit Reason
Custon Attributes
Refresh New Delete Automatic Exit Place
Search Criteria None
Place Name
Place Name
Beijin
Native
PC
seiver
New
Place Name
IP Address
Physical Information
Visitor Machine Type
FaceKiosk Name
Default Permissions
Area Name
Test
192 168 163 75
7575215100002
7575215100002
Area Name
FaceKiosk
Test Connection
Save and New OK Cancel
Step 1
Step 2
Step 3
Step 5
Step 4
15

Select an employee as the host. Click [Visitor Module] > [Basic Management] > [Host Levels]
> [New].
Sender Recipient
Search Criteria None
Refresh Delete Email Parameter Settings Export
Sender Recipient Subject Submit Time Send Time Status
Basic Management
Operation Log
Database Management
Area Settings
Department
E-mail Management
Dictionary Management
Data Cleaning
Audio File
Data Migration
Certificate Type
Print Template
System Monitoring
Parameters
Email Parameter Settings
Email Parameter Settings
Email Sending Server
Port
Email Account
Password
Sender Name
smtp.email.qq.com
[e-mail]
.......................
OK Close
Step 1
Step 2
Step 3
Step 5
Add the sender's mailbox to the software. The system will send an Email through the sender's
mailbox. Click [System] > [Basic Management] > [E-mail Management] > [Email Parameter
Settings].
Step 4
Note: For details, please refer to FaceKiosk-H13 Series User Manual.
16
Refresh New Delete
Search Criteria None
Edit the access level the host
Host Number Name More
New
Query Department Select all people
Personnel ID Name More
Search Criteria None
Alternative
Host
Number
Host First Name Host Last Name Department Name
Selected(0)
Host
Number
Host First Name Host Last Name Department Name
123456789
2
1
a
s
rr
a
s
jj
Department Name
Department Name
Department Name
1 - 3 50 rows per page Total of 3 records
OK Cancel
Step 1
Step 4
Step 5
Registration
Reservation
Basic Management
Parameters
Device Debugging
Print Settings
Visitor Levels
Host Levels
Visited Department Levels
Entry Place
Visit Reason
Custon Attributes
Step 2
Step 3

ZKTeco Industrial Park, No. 32, Industrial Road,
Tangxia Town, Dongguan, China.
Phone : +86 769 - 82109991
Fax : +86 755 - 89602394
www.zkteco.com
Copyright © 2022 ZKTECO CO., LTD. All Rights Reserved.