ZKTeco MB10-VL User manual

Quick Start Guide
Version: 1.1
2.8-inch Linux Visible Light Product

1
1.Overview
Near-infrared flash
2.8-inch Color Screen
Camera
Fingerprint Reader
& Card Reading Area
Keypad
COM1
NO1
BUT
GND
SEN
NC1
Sensor
Button
Lock
Powerport
Reset button
USB port
Network
interface
Flash
★
Note: Features and parameters with mark are not available in all devices. ★

2
2.Device Installation
①Attach the mounting template sticker to the wall, and drill holes according to
the mounting paper.
②Fix the back plate on the wall using wall mounting screws.
③After passing the wires through the wiring hole and connecting them to the
device, and then attach the device to the back plate from top to bottom.
④Fasten the device to the back plate with a security screw.
Install on the wall
1 2
43
1.1m
①
②
Baseline

3
3.Standalone Installation
Lock
TCP/IP
Exit button
Door sensor
PC
NC1
COM1
NO1
SEN
GND
BUT
Door sensor
Exitbutton
4.Door Sensor & Exit Button Connection
★

4
5.Lock Relay Connection
The system supports Normally Opened Lock and Normally Closed Lock.
The NO LOCK (normally unlocked when powered) is connected with 'NO' and
'COM' terminals, and the NC LOCK (normally locked when powered) is connected
with 'NC' and 'COM' terminals. Take NC Lock as an example below:
6.Power Connection
Recommended AC adapter ,: 5V 2A
To share the power with other devices, use an AC adapter with higher
current ratings.
DC 5V,2A
Not sharing power with the lock
DC5V +5V
GND
NC1
COM1
NO1
SEN
GND
BUT
FR107
DC12V
NC Lock

7.Ethernet Connection
Connect the device and computer software over an Ethernet cable. As shown in
the example below:
Default IP address: 192.168.1.201
: Subnet mask 255.255.255.0
: 192.168.1.130IP address
: 255.255.255.0 Subnet mask
8.Quick Start
UserRegistration User Authentication Viewrecords
Verified
User registration
5
User Mgt. User Role COMM.
System Personalize Data Mgt.
Department Shift Set Report
User Mgt.
New User
All Users
Display Style
New User
User ID
Name
User Role
Normal User
Department
Verification Mode
Password/Fingerprint/Face
Fingerprint
1
0
Click on [ ] > [ ] > [ ], input the IP address and click on [ ].Comm. Ethernet IP Address OK
Note: In LAN, the IP addresses of the server (PC) and the device must be in the same
network segment while connecting to the ZKBioAccess IVS software.
Method 1: Registering on the device
Press [M/OK] > [Main Menu] > [User Mgt.] > [New User]. Enter User ID, Name, User
Role, Department, Verification Mode and register Face, Fingerprint, Card Number ★
and Password, to register a user.

6
Method 2: Registering on the software (ZKBioAccess IVS)
Method 3: Registering on the phone
Please set the IP address and cloud service server address in the Comm. Menu option
on the device.
2. Click [Add] in operation column, a new window will pop-up. Select Attendance Area
3. Click [Personnel] > [Person] > [New] and fill in all the required fields to register a new
4. Click [Attendance Device] > [Device] > [Control] > [Synchronize Software Data to
the Device] to synchronize all the data to the device including the new users.
For more details, please refer to the ZKBioAccess IVS User Manual.
and Time zone from each dropdowns and click [OK] to add the device.
users in the software.
1. Click [Attendance] > [Attendance Device] > [Device] > [Search] to search the device
on the software. When an appropriate server address and port is set on the device,
the searched devices are displayed automatically.
Once the ZKBioAccess IVS software is installed, the users could enroll their face via a
browser application on their own mobile phone.
1. Click [Personnel] > [Parameters], input ‘’http://Server address: Port’’ in the QR Code
UGL bar. The software will automatically generate a QR code. Scan the QR code or
login onto ‘’http://Server address: Port/app/v1/adreg’’ by the mobile phone to register
users.
Attendance Device
Set Attendance By Area
Set Attendance By Person
Device
Attendance Point
Device Operation Log
Basic Information
Shift
Schedule
Exception
Calculate Report
Serial Number Device Name Attendance Area
The current query conditions None
Refresh Delete Search Control View / Get Clear Device Data
Serial Number Device Name Device Model Firmware Version IP Address Attendance Area Status Registration
Machine
Commands to be
Search
Search
Add
Total Progress
IP Address
Searched devices count:1
Number of devices added:1
Serial Number
IP Address Serial Number Device Type Operations
172.31.1.10 6698421030004
The current systen communication port is 8881, please make sure the device is set correctly.
Close
Step 1
Step 2
Step 3
Step 4
Step 5
172 31 1 10
6698421030004
Device Name
Serial Number
IP Address
Attendance Area
Time zone
Enrollment Device
6698421030004
Area Name
(UTC+8)Beijing,Chines
OK Cancel
Step 6

7
User Authentication
The terminal can detect the face within a range of 0.3m to 1.5m. The device switches to
the face verification interface automatically once it detects a change in environmental
brightness. The verification result shows the personnel details.
View records
View records on the software
Click [Device] > [Data] > [Transaction] on the software to view the records.
2020-12-3012:00
Successfully verified.
Name : Mike
User ID : 1
Verify : Face
Personnel
Person
Department
Pending Review
Custom Attributes
Parameters
Personnel ID Setting
The Maximum Length:
Support Letters:
Personnel ID Auto-increment:
Card Setting
The Maximum Length:
Card Format Display:
Pending personnel settings
Enable Auto-audit:
Self-service Registration
QR Code URL:
Yes No
Yes No
Bits(Binary)
Decimal Hexadecimal
Yes No
http://Server address:Port/app/v1/adreg
Download QR code image
9
32
Card Management
Personnel Registration
Personnel Registration
Personnel ID
First Name
Last Name
Last Name
Mike
4835
OK
2. The users will be displayed in [Personnel] > [Pending Review], click on [Review] option
and assign a department and click [OK] to successfully add the user.
Enable the declaration of health information: Yes No

User Mgt. User Role COMM.
System Personalize Data Mgt.
Department Shift Set Report
9.Access Control Settings
8
System Personalize Data Mgt.
Department Shift Set Report
Access
Control Attendance
Search
USB
Manager
Access Control
Access Control Options
Access Control Options
Door Lock Delay (s)
10
Door Sensor Delay (s)
10
Door Sensor Type
Normal Close (NC)
Door Alarm Delay (s)
30
Speaker Alarm
10.Ethernet and Cloud Server Settings
Ethernet
IP Address
Subnet Mask
Gateway
DNS
TCP COMM. Port
DHCP
192.168.1.201
255.255.255.0
0.0.0.0
0.0.0.0
4370
Cloud Server Setting
Server Mode
Enable Domain Name
Server Address
Server Port
Enable Proxy Server
HTTPS
0.0.0.0
8081
ADMS
Pressto enter the access control management interface [M/OK] > [Access Control]
and set relevant parameters of access control.
Press[M/OK] > [Comm.] > [Ethernet]to set the network parameters. If the TCP/IP
communication of the device is successful, the icon will be displayed in the
upper right corner of the standby interface.
Press[M/OK] > [Comm.] > [Cloud Server Setting] to set the server address and
server port,that is, the IP address and port number of the server after the software
is installed. If the device communicates with the server successfully, the icon will
be displayed in the upper right corner of the standby interface.