Zodiac WR000411 User manual

Installaon and user manual - English
Baery-powered electric cleaner
Translaon of the original instrucons in French
H0753400.B - 2022/09 - EB----
More documents on:
www.zodiac.com
EN
according to product marking

1
WARNINGS
• Before handling the appliance, it is vital that you read this installaon and user
manual, as well as the "Warranes" booklet delivered with the appliance. Failure
to do so may result in material damage or serious or fatal injury and will void the
warranty.
• Keep and pass on these documents for reference during the appliance's service life.
• The distribuon or modicaon of this document in any way is prohibited, without
prior authorisaon from Zodiac®.
• Zodiac® is constantly developing its products to improve their quality. The informaon
contained herein may therefore be modied without noce.
GENERAL WARNINGS
• Failure to respect the warnings may cause serious damage to the pool equipment or
cause serious injury, even death.
• Only a person qualied in the technical elds concerned (electricity,
hydraulics or refrigeraon) is authorised to carry out maintenance or
repair work on the appliance. The qualied technician working on the
appliance must use/wear personal protecve equipment (such as safety
goggles and protecve gloves, etc.) in order to reduce the risk of injury
occurring when working on the appliance.
• Before handling the appliance, check that it is switched o and isolated.
• The appliance is intended to be used for pools and spas for a specic purpose; it
must not be used for any purpose other than that for which it was designed.
• This appliance is not intended for use by individuals (including children) with
impaired physical, sensorial or mental abilies, or persons lacking in knowledge
and experience, unless they receive supervision or prior instrucons on using the
appliance from a person responsible for their safety. Children must be supervised to
ensure that they do not play with the appliance.
• This appliance can be used by children under 8 and adults with impaired physical,
sensory or mental capabilies, or who lack experience and knowledge, if they are
correctly supervised or have been instructed in how to use the appliance safely and
understand the hazards involved. Children and pets shall not play with the appliance.
This is not a toy. User cleaning and maintenance operaons must not be carried out
by children without supervision.
• The charging of the appliance must follow standard IEC / HD 60364-7-702 and
required naonal rules for swimming pools, should you have any doubts please
consult your dealer.
• The appliance must be installed according to the manufacturer’s instrucons and
in compliance with local and naonal standards. The installer is responsible for
installing the appliance and for compliance with naonal installaon regulaons.
Under no circumstances may the manufacturer be held liable in the event of failure
to comply with applicable local installaon standards.
• For any work other than the simple user maintenance described in this manual, the
product should be referred to a qualied professional.
• If the appliance suers a malfuncon, do not try to repair it yourself; instead contact
a qualied technician. The product manufacturer is exempt from all liability regarding
any damage caused by unauthorized spare parts or accessories.
• Refer to the warranty condions for details of the permied water balance values
for operang the appliance.
• Deacvang, eliminang or by-passing any of the safety mechanisms integrated
into the appliance shall automacally void the warranty, in addion to the use of
spare parts manufactured by unauthorised third-party manufacturers.
• Do not spray inseccide or any other chemical (inammable or non-inammable) in
the direcon of the appliance, as this may damage the body and cause a re.
• Do not touch the fan or moving parts and do not place objects or your ngers in the
vicinity of the moving parts when the appliance is in operaon. Moving parts can
cause serious injury or even death.
• Do not operate the cleaner or leave outside during freezing weather condion.
EN

2
WARNINGS ASSOCIATED WITH ELECTRICAL APPLIANCES
• The power supply to the appliance charging staon must be protected by a dedicated
30 mA Residual Current Device (RCD), complying with the standards and regulaons
in force in the country in which it is installed. Contact a qualied electrician if you
cannot verify that the circuit is protected by a RCD.
• Do not use any extension lead when connecng the charging staon; connect the
staon directly to a suitable power supply.
• Before carrying out any operaons, check that:
- The required input voltage indicated on the charging staon informaon plate
corresponds to the mains voltage;
- The mains supply is compable with the appliance's electricity needs and is correctly
grounded.
• In the event of abnormal operaon or the release of odours from the appliance, turn
it o immediately, unplug the appliance from the charging staon where necessary
and contact a professional.
• Before servicing or performing maintenance on the appliance, check that it is
powered o and completely disconnected from the charging staon and that all
other equipment or accessories connected to the appliance are also disconnected
from the power circuit.
• If the power cord is damaged, it must be replaced by the manufacturer, an authorised
representave or a repair facility only.
• Before connecng the appliance to the charging staon, check that the connecon
unit or socket to which the appliance will be connected is in good condion and
shows no signs of damage or rust.
• In stormy weather, disconnect the appliance from the power supply to prevent it
from suering lightning damage.
• The product contains magnets and components that emit electromagnec elds.
The magnets and electromagnec elds can interfere with pacemakers, debrillators
and other medical devices. Keep a safe distance between the medical device and the
product. Consult your doctor or the manufacturer of the medical device for specic
informaon about it. If you think that the product is interfering with a pacemaker,
debrillator, or any other medical device, stop using the product starng from the
distance at which you feel interference.
WARNINGS ASSOCIATED WITH BATTERY-POWERED ELECTRICAL APPLIANCES
• Do not use a baery block, cleaner or charging staon that is damaged or modied.
Damaged or modied baeries may exhibit unpredictable behavior resulng in re,
explosion or risk of injury.
• Do not handle the cleaner and the charging staon while it is charging with wet
limbs and without shoes.
• Do not aempt to clean the impeller when the cleaner is in water or on a wet surface.
This may lead to severe injury.
• Recharge only with the charging staon specied by the manufacturer. A charging
staon that is suitable for one type of baery pack may create a risk of re when
used with another baery pack.
• Do not expose charging staon or cleaner to re or excessive temperature. Exposure
to re or temperature above 65°C may cause explosion.
• The appliance must be charged in a temperature between 5-35°C.
• Follow all charging instrucons and do not charge the baery operated appliance
outside of the temperature range specied in the instrucons. Charging improperly
or at temperatures outside of the specied range may damage the baery and
increase the risk of re.
• The charging staon can be used indoor in a dry and well venlated area or outdoor
in dry area, away from direct sunlight, children, heat, ignion sources, and pool
chemicals.
• Never aempt to open the charging staon.
• Do not touch the charge plates on the charging staon or on the cleaner aer
charging because of the temperature of these components during charging.
• The baery installed is a rechargeable Li-ion baery pack. Never aempt to
disassemble or replace it. A baery can produce a short circuit causing severe burns.
EN

3
Avoid contact between any wires or metal items that could cause sparking and short
circuit the baery. If a baery leak occurs, avoid any contact with the leaking uids
and contact a professional to replace the baery. Wear complete eye protecon,
gloves and protecve clothing when disposing of cleaner. If leaking uids come in
contact with skin and clothing, wash immediately with plenty of soap and water. If
leaking uids come in contact with eyes, do not rub eyes, immediately ush eyes
with cool running water for at least 15 minutes and do not rub them. Seek medical
aenon as soon as possible.
• Baery and cleaner must be disposed of in accordance with local requirements.
Always dispose of baeries in a sustainable way in approved collecon bins or
at authorised collecon centers in accordance with local law. Contact your local
authority for more informaon.
SPECIFIC FEATURES APPLICABLE TO "Pool cleaners"
• The cleaner is designed to operate properly in pool water at a temperature of
between 10°C and 35°C.
• To avoid possible injury or damage to the cleaner, do not operate the cleaner out of
the water.
• In order to prevent possible injury, bathing is prohibited when the cleaner is in the
pool.
• Do not use the cleaner during shock chlorinaon.
• Do not leave the cleaner unaended for an extended period.
• If you are planning on using the robot in a saltwater pool, make sure all salts are
dissolved before placing it into the water.
WARNING ON THE USE OF A CLEANER IN A POOL WITH A LINER
• Before installing the cleaner, carefully inspect the pool lining. If the liner comes
away or is damaged in places, or if stones, folds, roots or corrosion appear, do not
install the cleaner before a qualied professional repairs or replaces the liner. The
manufacturer may not be held liable in any way for damage caused to the liner.
• The surface of certain paerned liners can wear away quickly: the paerns and/
or colours can become deteriorated, faded or disappear on contact with certain
objects (cleaning brushes, toys, rubber rings and oats, chlorine dispensers, or
cleaners). The cleaner manufacturer may not be held liable for wear to the liners or
faded paerns, which are not covered by the limited warranty.
WARNING ON THE USE OF A CLEANER IN A STAINLESS STEEL POOL
• The surface of some stainless steel pools may actually be very fragile. The surface
of these pools can become damaged by the natural rubbing of debris against the
coang, caused for example by cleaner wheels, tracks or brushes, including those
of electric pool cleaners. The cleaner manufacturer may not be held liable for wear
or scratching aecng stainless steel pools, which are not covered by the limited
warranty.
Recycling
This symbol is required by the European direcve DEEE 2012/19/EU (direcve on waste electrical and electronic
equipment) and means that your appliance must not be thrown into a normal bin. It will be selecvely collected
for the purpose of reuse, recycling or transformaon. If it contains any substances that may be harmful to the
environment, these will be eliminated or neutralised. Contact your retailer for recycling informaon.
EN

4
CONTENTS
❶ Informaon before using the appliance 5
1.1 I Descripon 5
1.2 I Technical specicaons and parts list 6
1.3 I Operang principle 7
1.4 I Pool preparaon 7
❷ General use 8
2.1 I Assembling the charging staon 8
2.2 I Installing the staon and charging the cleaner 9
2.3 I Descripon of the interface 10
2.4 I Descripon of the indicators 11
2.5 I Starng a cleaning cycle 12
2.6 I Removing the cleaner from the water 14
2.7 I Storing the cleaner 15
❸ Using the iAquaLink™ app 16
3.1 I First-me cleaner conguraon 16
3.2 I Funcons available in the iAqualink™ app 17
❹ Maintenance 18
4.1 I Cleaning the cleaner and charging staon 18
4.2 I Cleaning the lter 18
4.3 I Cleaning the brushes and the centre bridge 19
4.4 I Cleaning the cover seal 19
4.5 I Cleaning the propeller 20
4.6 I Replacing the brushes 21
4.7 I Replacing the baery block 22
4.8 I Winterising 22
❺ Troubleshoong 23
5.1 I Appliance behaviour 23
5.2 I Charging staon behaviour 24
5.3 I User alerts 25
5.4 I Troubleshoong the connecon to the iAquaLink™ app 27
Tip: to make it easier to contact the retailer
Write down the retailer's contact details to help you nd them more easily and ll in the "product" informaon on the
back of the manual: the retailer will ask for this informaon.
EN

5
❶ Informaon before using the appliance
1.1 I Descripon
Cleaner
Dual ltraon (150/60 µ)
Charging staon (to assemble)
Foot (x2)
Hook*
Hook holder
Single ltraon (100 µ)
* To mount on a pool pole (standard, not supplied): Required to remove the cleaner from the water.
: Included
: Available as an opon
x2
EN

6
1.2 I Technical specicaons and parts list
1.2.1 Technical specicaons
Charging staon power supply voltage 100 - 240 VAC, 50/60Hz, Class II*
Cleaner power supply voltage 25.4 VDC
Charge voltage 29.4 VDC
Charger maximum power 58 W
Baery capacity 10 Ah
Cleaner rated power 130 W
Filter capacity 4 L
Cleaner size (L x W x h) 41 x 42 x 28 cm
Package size (L x W x H) 56 x 56 x 38 cm
Cleaner weight 9.2 kg
Packaged weight 15.5 kg
Sucon width 230 mm
Maximum operang depth 4 m
Protecon rang Charging staon IPX5
Cleaner IPX8
Frequency bands 2.412GHz - 2.484GHz
Radio output power 20.5 dBm
* Class II: appliance with double insulaon or reinforced insulaon that does not require grounding.
1.2.2 Parts list

Handle
Tracks
Filter access
Brushes
Cursor
Centre bridge
(between the two brushes)
Cover seal
Baery indicator
EN

7
1.3 I Operang principle
The cleaner is independent of the ltraon system and can, once charged, operate autonomously. It nds the best route
to move around and clean the areas of the pool for which it has been designed (oor, walls, waterline or oor only).
Debris is sucked in and stored in the cleaner's lter.
The cleaner can be used:
- By selecng an operang mode and starng a cycle with the cursor on the rear of the cleaner, or
- Via a smartphone or a tablet compable with the iAquaLink™ app (see "❸ Using the iAquaLink™ app").
3.5 meters
minimum
: Charging staon
: Plug
: Cleaner
: “iAquaLink™”
remote control
1.4 I Pool preparaon
• This product is intended to be used in pools which are permanently installed. Do not use it in pools
which may be dismantled. A permanent pool is built into the ground or on the ground and cannot be easily
dismantled and stored.
• The appliance must operate in pool water with the following properes:
Water temperature Between 10°C and 35°C
pH Between 6.8 and 7.6
Free chlorine < 3 mg/ l
• When the pool is especially dirty, especially when commissioning, remove the largest debris using a net in order to
opmise the appliance's performances.
• Remove any thermometers, toys and other objects that might damage the appliance.
EN

8
❷ General use
2.1 I Assembling the charging staon
Assemble the charging staon before use:
• Slide the top of the foot (marked with a blue dot) into the slot at the front of the charging staon (also marked with
a blue dot) ( ).
• Push the foot fully home under the staon (the boom of the foot ( ) should clip in).
• Aach the hook on the side of the charging staon (on the right or the le to match the desired locaon) ( ).
• Roll out the cable to run it to the rear of the staon or on one side, depending on the desired installaon (a slot to
hold the cable is provided inside each foot).
Click
Cable location
EN

9
2.2 I Installing the staon and charging the cleaner
• The staon must not be immersed in water or any other liquid. It must not be installed in a oodable
area.
• DO NOT place charging staon in direct sunlight.
• Place the charging staon:
- Close to an easily accessible power outlet (located out of the rain and from splashing),
- in the shade. DO NOT expose cleaner and base to direct sunlight when charging cleaner.
- more than 3.5 metres from the edge of the pool.
3.5 m
and over
Less than
3.5 m
• Connect the charging staon.
• Posion the cleaner on the charging staon so that the rear of the cleaner (the cursor end) come into contact with
the slots provided on the rear of the staon. When the cleaner is correctly posioned, an audible signal is heard and
the indicator
  
blinks slowly (orange).
• Temperature range for charging : 5 - 35°C.
• Make sure that the charge plates on the charging staon and on the cleaner are clean and dry before
charging.
• Do not touch the charge plates on the charging staon or on the cleaner right aer recharging the
cleaner.


Bip
Handle
Slot
Cursor
3-4
hours
• Before using the cleaner for the rst me, charge it fully (for 3 to 4 hours): The indicator
  
changes to steady (green)
once it is fully charged. Charging stops automacally as soon as the cleaner is fully charged. Therefore there is no
need to disconnect the staon or to remove the cleaner.
• When all of the indicators are o, the cleaner is on standby. Slide the cursor to the le or to the right to
wake up the cleaner. If this does not work, place the cleaner back on the charging staon (the cleaner goes
into deep sleep aer 8 days of inacvity).
• If the indicator
  
does not blink when the cleaner is rst placed on charge, see "5.1 I Appliance
behaviour".
• To get the advantages of connecvity (soware updates, baery status, informaon on the cycle, see
"3.2 I Funcons available in the iAqualink™ app"), place the charging staon in a locaon where Wi-Fi is
accessible.
EN

10
2.3 I Descripon of the interface
Thanks to the interface on the rear of the cleaner, you can choose the cleaning mode and start a cleaning cycle and also
get informaon on cleaner, baery or connecvity status.
Addional funcons and informaon can also be accessed from the app, see "❸ Using the iAquaLink™ app".
Funcon
Keys

Cursor (choice of mode, start a cycle, see "2.5 I Starng a
cleaning cycle")
Indicator lights

Baery status
 
"Floor + walls + waterline" mode acvated
 
"Floor" mode acvated
 
Cleaner status
 
Wi-Fi connecon status
• When all of the indicators are o, the cleaner is on standby. Slide the cursor to the le or to the right to
wake up the cleaner. If this does not work, place the cleaner back on the charging staon (the cleaner goes
into deep sleep aer 8 days of inacvity).
EN

11
2.4 I Descripon of the indicators
2.4.1
 
Cleaner status indicator
➔ Blinking indicator ➔ Indicator on
Blue
Ready for immersion
Blue Cycle in progress
Red
Cleaner error, see "5.3.1 Cleaner error"
2.4.2

Charge indicator
➔ Blinking indicator ➔ Indicator on
Green Charged: ready for use
Green
Charging : ready for use
Orange Parally charged: can be used (cycle will be shorter)
Orange
• If the cleaner is on the staon: Charging
• If the cleaner is not on the staon: Needs to be recharged and cannot be used
Red
Baery error, see "5.3.2 Baery error"
2.4.3

Connecvity indicator
➔ Blinking indicator ➔ Indicator on
O Not connected to Wi-Fi
Blue
Connecng
Blue Connected to Wi-Fi
2.4.4 Charging staon status indicator
An indicator under the charging staon shows its status.
➔ Indicator on
Green
• Staon powered, not charging
• If the indicator is green and the cleaner is on the staon, see
"5.2 I Charging staon behaviour".
Red Cleaner charging
• If the indicator is o or blinking when the staon is plugged in, see "5.2 I Charging staon behaviour".
EN

12
2.5 I Starng a cleaning cycle
In order to avoid any risk of injury or material damage, follow the instrucons below:
• Bathing is prohibited when the appliance is in the pool.
• Do not use the appliance during a shock chlorinaon. Wait unl the chlorine level has reached the
recommended value before immersing the cleaner.
• If the pool is covered, use the "Floor only" cleaning mode.
To start the cleaning cycle:
• Wait unl the cleaner is fully charged (
  
green) to start a cycle.
• Once charged, remove it from its charger staon and take it to the pool.
• Choose the cleaning mode, see "2.5.1 Choice of cleaning mode".
• Start the cycle, see "2.5.2 Starng the cleaning cycle".
• Immerse the cleaner, see "2.5.3 Immersing the cleaner".
2.5.1 Choice of cleaning mode
The cleaning mode denes the surface to be cleaned and the duraon of the cleaning cycle.
• Slide the cursor on the rear of the cleaner to the le:
- One notch to select the "Floor only" mode,
- A second notch to select the "Floor + walls + waterline" mode.
The indicator corresponding to the mode will light.
Surface to clean Cycle duraon
Floor + walls +
waterline 2h30
Floor only 1h30
• Addional modes are available via the applicaon (Waterline mode, Smart mode), see "3.2 I Funcons
available in the iAqualink™ app").
EN

13
2.5.2 Starng the cleaning cycle
• Slide the cursor on the rear of the cleaner to the right to start the cycle.
• The indicator
 
blinks while waing for the cleaner to be immersed.
Tip: To improve cleaning performance
• At the start of the bathing season, run several cleaning cycles in oor only mode (aer removing the
large debris with a net). Regular use of the cleaner (without exceeding 3 cycles per week) means that your
pool will always be clean and the lter less clogged. We recommend running a few cycles without the
debris lter to perform a rough clean, see "4.2 I Cleaning the lter" to disassemble the lters.
2.5.3 Immersing the cleaner
• Place the cleaner vercally into the water and hold it there while moving it slightly in all direcons so that the air
contained in it escapes.
• Let the cleaner sink to the boom of the pool. The cycle will start at the latest 40 seconds aer the cleaner detects
that it is in water. The cleaner adapts its movement strategy to the cleaning mode, in order to opmise its level of
coverage.
EN

14
2.6 I Removing the cleaner from the water
• Using the pole, you can remove the cleaner during the cycle and the cleaner will stop automacally
once it is out of the water.
• At the end of a cycle, the cleaner always stops at the foot of a side.
2.6.1 Without the iAquaLink™ app
• During the last ten minutes of the cycle, the cleaner will successively climb the various sides and wait at the waterline
unl it is recovered using the handle ( ) (not available in the "Floor only" mode).
• If it is not retrieved at this me, the cleaner at the foot of a side at the end of the cycle ( ).
• Aach the hook (supplied) to the end of a pool pole (not supplied) ( ).
• Catch the cleaner handle with the hook and raise the cleaner to the surface ( ).
• Use the handle to take it out of the water. The cleaner expels water through a rear jet to make it lighter ( ).
EN

15
2.6.2 With the iAquaLink™ app
• When Push nocaons have been allowed (iAqualink™ app phone's sengs), the cleaner warns you that the cycle is
coming to an end. From this me on and during the last ten minutes of the cycle, the cleaner will successively climb
the various sides and wait at the waterline unl it is recovered using the handle ( ) (not available in the "Floor only"
mode).
• Use the handle to take it out of the water. The cleaner expels water through a rear jet to make it lighter ( ).
2.7 I Storing the cleaner
• DO NOT leave the cleaner uncharged: always recharge the cleaner aer use.
• Make sure that the cleaner and the charge plates are clean and dry before charging.
• DO NOT leave the cleaner to dry out in sunlight aer use.
• DO NOT leave cleaner in water when not in use.
• DO NOT expose cleaner to re, excessive temperatures, ignion sources, or pool and spa chemicals.
• Store all the elements away from sunlight, humidity and bad weather.
• Store out of reach of children and pets.
• Place the dry cleaner on the charging staon.
• Store all elements away from direct sunlight and any splashes.


Bip
Handle
Rear grill
EN

16
❸ Using the iAquaLink™ app
Mobile device
(smartphone or tablet) Home Wi-Fi
network Cleaner
The iAquaLink™ app is available for iOS and Android systems.
3.1 I First-me cleaner conguraon
Before you install the app, you must:
• First charge the cleaner,
• Use a Wi-Fi-enabled smartphone or tablet,
• Use a Wi-Fi network with a signal that is powerful enough to connect to the cleaner: It must be possible
to detect the Wi- Fi signal where the cleaner is used. If this is not the case, a technical soluon must be
provided to amplify the exisng signal.
• Have your home Wi-Fi network password at the ready.
• Download the iAquaLink™ app from the App Store (iOS) or Google Play Store (Android).
Log in or register. Press the + icon to add a new appliance and follow
the instrucons in the app.
Follow the steps displayed in the app. When required, slide the cursor to the right and maintain it for 10
seconds, unl the

indicator blinks to acvate the Bluetooth™.
 
 
 
O Flashing Steady
• A message is displayed on-screen to show that the Wi-Fi connecon has been correctly established between the
cleaner and the home router. (*)
• The

indicator on the rear of the cleaner comes on.
(*): If an error message appears or if the connecon sll isn't made, refer to the table "5.3 I Troubleshoong
the connecon to the iAquaLink™ app".
EN

17
3.2 I Funcons available in the iAqualink™ app
• When the cleaner is in the water, iAqualink™ app funcons are no longer available.
When the cleaner is out of the water, the app allows:
• Choosing a mode and starng a cycle. Starng a cleaning cycle from the app opens a pop-up. Close the pop-up to
allow the cleaner to start.
• Accessing two modes exclusively available in the app: The "Waterline" mode and the "Smart" mode (automac me
adjustment),
• Accessing the troubleshoong assistance funcons via errors returned : press the warning symbol to display the
troubleshoong soluons, see "5.3 I User alerts".
• Easier removal from the pool: When Push nocaons have been allowed (iAqualink™ app phone's sengs), the app
informs you when the cleaner is waing to be removed at the waterline of the pool (during the last ten minutes of the
cycle) (not available in the "Floor only" mode).
• Informing you of the cleaner charge level.
Charged: ready for use
Charging: ready for use
Charging
Parally charged
When the cleaner is out of the water, press the icon to access certain informaon on the cleaner at any me (serial
number, etc.) via the Sengs Menu and access.
EN

18
❹ Maintenance
• Tip: To ensure the longest possible lifeme for the cleaner, inspect all of the parts for which servicing is
detailed in the "❹ Maintenance" secon, once a month.
4.1 I Cleaning the cleaner and charging staon
• The appliance must be cleaned regularly using clean or slightly soapy water. Do not use solvents.
• The charge plates under the cleaner and on the charging staon must be cleaned regularly using a cloth or the
scouring side of a kitchen sponge and fresh water. Do not use metal sponges, metal brushes, solvents or salt water.
• Rinse the appliance thoroughly with clean water.
• Do not let the appliance dry in the sun by the pool.
4.2 I Cleaning the lter
• The cleaner's performance may be reduced if the lter is full or dirty.
• Clean the lter with clean water aer each cleaning cycle.
• Use the (black) ne debris lter only when using the cleaner for the rst me or when it comes out of
winter storage.
• If the lter is clogged, clean it with an acidic soluon (spirit vinegar, for example). It is recommended that you do this
at least once a year, since the lter will clog if not used for several months (winterising period).
Very ne
debris lter
Fine
debris lter
EN

19
4.3 I Cleaning the brushes and the centre bridge
• The performance of the appliance may diminish if the brushes are too dirty or if debris or objects
become trapped in the centre bridge (between the two brushes).
• Clean the brushes and the centre bridge in clean water as soon as the appliance is removed from the pool aer each
cleaning cycle. Do not wait for the debris to dry.
• Remove any object or debris trapped between the two brushes.
4.4 I Cleaning the cover seal
• Appliance performance may diminish if debris (mainly sand) becomes trapped under the cover seal,
making it impossible to maintain the necessary waterproong.
• Clean the cover seal in clean water as soon as the appliance is removed from the pool aer each cleaning cycle. Do
not wait for the debris to dry.
• Tip: To preserve the integrity of the cleaner and guarantee opmum performance:
- The lter and brushes should be replaced every two years,
- Checking the wear indicator on the tracks is recommended. Replace the tracks as soon as the indicator is
reached.
EN