ZURN Z880 User manual

Zurn Industries, LLC | Specification Drainage Operation
1801 Pittsburgh Avenue, Erie, PA U.S.A. 16502 · Ph. 855-663-9876, Fax [phone]
In Canada | Zurn Industries Limited
3544 Nashua Drive, Mississauga, Ontario L4V 1L2 · Ph. 905-405-8272, Fax [phone]
www.zurn.com
Rev. A
Date: 5/15/2018
C.N. No. 140024
Form No. FT902 Page 1 of 7
Dimensional data (inches and [mm]) are subject to manufacturing tolerances and change without notice.
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov
ADVERTENCIA: Cáncer y daño reproductivo - www.P65Warnings.ca.gov
AVERTISSEMENT: Cancer et effets néfastes sur la reproduction - www.P65Warnings.ca.gov
Z880
SHALLOW TRENCH DRAIN SYSTEM INSTALLATION INSTRUCTIONS

Zurn Industries, LLC | Specification Drainage Operation
1801 Pittsburgh Avenue, Erie, PA U.S.A. 16502 · Ph. 855-663-9876, Fax [phone]
In Canada | Zurn Industries Limited
3544 Nashua Drive, Mississauga, Ontario L4V 1L2 · Ph. 905-405-8272, Fax [phone]
www.zurn.com
Rev. A
Date: 5/15/2018
C.N. No. 140024
Form No. FT902 Page 2 of 7
Dimensional data (inches and [mm]) are subject to manufacturing tolerances and change without notice.
Z880
ACCESSORIES
Above are some of the trench drain components typical to an installation. Double check your order to ensure that you have all
components particular to your job before beginning your installation.
Contact Zurn ‘Flo-Thru’ at 855-663-9876 should additional material be required.

Zurn Industries, LLC | Specification Drainage Operation
1801 Pittsburgh Avenue, Erie, PA U.S.A. 16502 · Ph. 855-663-9876, Fax [phone]
In Canada | Zurn Industries Limited
3544 Nashua Drive, Mississauga, Ontario L4V 1L2 · Ph. 905-405-8272, Fax [phone]
www.zurn.com
Rev. A
Date: 5/15/2018
C.N. No. 140024
Form No. FT902 Page 3 of 7
Dimensional data (inches and [mm]) are subject to manufacturing tolerances and change without notice.
Z880
EXCAVATION
Trench excavation must be 4" [102mm] greater than the trench depth and a minimum of 4" [102mm] greater than the edge of
the trench on each side. Soft and/or shifting soil substrates may cause cracking of the concrete and consequent movement
of the trench. It is critical that the concrete be poured on an adequate foundation.

Zurn Industries, LLC | Specification Drainage Operation
1801 Pittsburgh Avenue, Erie, PA U.S.A. 16502 · Ph. 855-663-9876, Fax [phone]
In Canada | Zurn Industries Limited
3544 Nashua Drive, Mississauga, Ontario L4V 1L2 · Ph. 905-405-8272, Fax [phone]
www.zurn.com
Rev. A
Date: 5/15/2018
C.N. No. 140024
Form No. FT902 Page 4 of 7
Dimensional data (inches and [mm]) are subject to manufacturing tolerances and change without notice.
Z880
JOINT CONNECTION
Assembling the trench run is easy using ‘Flo-Thru’s’ mechanical interlocking joints. Simply align the male end above the
female end and slide together. The bottom interlock should snap together. A silicone caulk, or a construction adhesive, such
as Liquid Nails, is recommended to be used at each joint as a sealer.

Zurn Industries, LLC | Specification Drainage Operation
1801 Pittsburgh Avenue, Erie, PA U.S.A. 16502 · Ph. 855-663-9876, Fax [phone]
In Canada | Zurn Industries Limited
3544 Nashua Drive, Mississauga, Ontario L4V 1L2 · Ph. 905-405-8272, Fax [phone]
www.zurn.com
Rev. A
Date: 5/15/2018
C.N. No. 140024
Form No. FT902 Page 5 of 7
Dimensional data (inches and [mm]) are subject to manufacturing tolerances and change without notice.
Z880
OUTLETS AND ACCESSORIES
To attach an end outlet or end cap, cut trench to desired length if necessary and attach with provided screws and a silicone
caulk or a construction adhesive if desired.
A bottom outlet is attached to the bottom side of the trench drain with provided screws and a silicone caulk or a construction
adhesive if desired as shown below. It may be necessary to remove a underside rib to allow the outlet to sit flat. A hole saw
can be used to cut the appropriate size hole through the bottom of the trench.

Zurn Industries, LLC | Specification Drainage Operation
1801 Pittsburgh Avenue, Erie, PA U.S.A. 16502 · Ph. 855-663-9876, Fax [phone]
In Canada | Zurn Industries Limited
3544 Nashua Drive, Mississauga, Ontario L4V 1L2 · Ph. 905-405-8272, Fax [phone]
www.zurn.com
Rev. A
Date: 5/15/2018
C.N. No. 140024
Form No. FT902 Page 6 of 7
Dimensional data (inches and [mm]) are subject to manufacturing tolerances and change without notice.
Z880
OVERALL LAYOUT
Upon completion of the trench excavation, the channels should be placed in order alongside the excavation and according to
the job layout.

Zurn Industries, LLC | Specification Drainage Operation
1801 Pittsburgh Avenue, Erie, PA U.S.A. 16502 · Ph. 855-663-9876, Fax [phone]
In Canada | Zurn Industries Limited
3544 Nashua Drive, Mississauga, Ontario L4V 1L2 · Ph. 905-405-8272, Fax [phone]
www.zurn.com
Rev. A
Date: 5/15/2018
C.N. No. 140024
Form No. FT902 Page 7 of 7
Dimensional data (inches and [mm]) are subject to manufacturing tolerances and change without notice.
Z880
SETTING THE TRENCH
After attachment of acessories, anchor and level trench in the excavation using concrete patties around the feet. Make finish
pour of concrete and be certain to properly vibrate concrete to eliminate any unwanted voids. Finish troweling should be done
to set the top edge of the trench drain 1/16” [1.6mm] below the floor grade. Remember to compensate for concrete shrinkage
that may occur durning cure so that the edge of the trench drain does not protrude above the finished floor grade.