ZURN EZ1 Service manual

EZ1TM CLEANOUT SERIES
EZ1TM FLOOR CLEANOUT INSTALLATION INSTRUCTIONS
Zurn Industries, LLC | Specification Drainage Operation
1801 Pittsburgh Avenue, Erie, PA U.S.A. 16502 · Ph. 855-663-9876, Fax [phone]
In Canada | Zurn Industries Limited
3544 Nashua Drive, Mississauga, Ontario L4V 1L2 · Ph. 905-405-8272, Fax [phone]
www.zurn.com
Rev. C
Date: 02/27/2018
C.N. No. 139680
Form No. CO18 Page 1 of 6
®
Fig. 1
1. Cut pipe so that the height of the finished cleanout is at or just
below the height of the finished floor. (See Zurn Engineering
Handbook or EZ1TM Submittal for dimensional heights). Ensure
pipe is cut square and free of burrs or debris. See Fig. 1
2. Install cleanout body on pipe and pressure test connection per
local code requirements. See Fig. 2 (Neo-loc body shown for
reference)
Ensure that the cleanout plug is installed using an approved
thread sealant.
Note: All plastic bodies to be solvent welded to pipe.
3. Adjust rough-in cover assembly so the top of the rough-in cover
is at the finish floor grade. See Fig. 3
Note: Ensure rough-in cover is tight to the concrete shield
so no concrete seeps into the assembly
Fig. 2
No Gap
Warning: Flying material can cause eye injury or blindness and sharp edges could cause cuts or
lacerations. Wear safety glasses and gloves when installing or working on cleanout.
Fig. 3
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov
ADVERTENCIA: Cáncer y daño reproductivo - www.P65Warnings.ca.gov
AVERTISSEMENT: Cancer et effets néfastes sur la reproduction - www.P65Warnings.ca.gov

EZ1TM CLEANOUT SERIES
EZ1TM FLOOR CLEANOUT INSTALLATION INSTRUCTIONS
Zurn Industries, LLC | Specification Drainage Operation
1801 Pittsburgh Avenue, Erie, PA U.S.A. 16502 · Ph. 855-663-9876, Fax [phone]
In Canada | Zurn Industries Limited
3544 Nashua Drive, Mississauga, Ontario L4V 1L2 · Ph. 905-405-8272, Fax [phone]
www.zurn.com
Rev. C
Date: 02/27/2018
C.N. No. 139680
Form No. CO18 Page 2 of 6
®
Fig. 4
Fig. 6
Fig. 5
4. Pour finish floor slab flush to the top of the rough-in cover.
See Fig. 4
Note: If fixture is above floor surface, it is recommended to
hand finish concrete around fixture to avoid damage.
5. Hit the top of the rough-in cover with a pair of adjustable
pliers to loosen bond with the concrete. Continue hitting
the rough-in cover until a visible crack forms around the
entire circumference of the rough-in cover. The rough-in
cover should appear loose (separates from concrete).
See Fig. 5
Note: Be careful to not hit the finished concrete floor
as it will chip/damage the finish. Only hit the plastic
rough-in cover. Do not use excessive force.
6 Break the protective label in the center of the rough-in cover
to expose a slot. See Fig. 6
Note: Do not remove entire label. Longer screws and
adjustment shims are packaged under the label.

EZ1TM CLEANOUT SERIES
EZ1TM FLOOR CLEANOUT INSTALLATION INSTRUCTIONS
Zurn Industries, LLC | Specification Drainage Operation
1801 Pittsburgh Avenue, Erie, PA U.S.A. 16502 · Ph. 855-663-9876, Fax [phone]
In Canada | Zurn Industries Limited
3544 Nashua Drive, Mississauga, Ontario L4V 1L2 · Ph. 905-405-8272, Fax [phone]
www.zurn.com
Rev. C
Date: 02/27/2018
C.N. No. 139680
Form No. CO18 Page 3 of 6
®
7. Placing the back of the adjustable pliers head in the slot,
unscrew the rough-in cover assembly counterclockwise until
the tabs of the rough-in cover are above the concrete.
See Fig. 7
8. Remove rough-in cover. See Fig. 8
Note: Do not discard the rough-in cover. Longer
screws and adjustment shims are under the label and
may be needed to adjust for a tilted cleanout.
Fig. 7
Fig. 8
Above the
concrete

EZ1TM CLEANOUT SERIES
EZ1TM FLOOR CLEANOUT INSTALLATION INSTRUCTIONS
Zurn Industries, LLC | Specification Drainage Operation
1801 Pittsburgh Avenue, Erie, PA U.S.A. 16502 · Ph. 855-663-9876, Fax [phone]
In Canada | Zurn Industries Limited
3544 Nashua Drive, Mississauga, Ontario L4V 1L2 · Ph. 905-405-8272, Fax [phone]
www.zurn.com
Rev. C
Date: 02/27/2018
C.N. No. 139680
Form No. CO18 Page 4 of 6
®
For Slab On Grade Installation (Steps 9 and 10)
If finished fixture is tilted, See Step 13
Round
9a. Place a bead of silicone around the circumfrence of the last
thread of the head assembly. See Fig. 9R
9b. Thread head assembly down until bottom of the frame is flush
with the top of the concrete. See Fig. 9R
9c. Place a bead of silicone around the perimeter of the cover
frame. See Fig. 9R
10. Turn head assembly clockwise until top of cover is flush with
the finish floor. Wipe away excess silicone. Remove protective
label once construction is complete. See Fig. 10R
Square
9. Turn head assembly clockwise until top of strainer is flush with
the finish floor. See Fig. 9S
10. Fill in rough-in adapter with cement or grout. Ensure to
completely fill in around entire head assembly flush with
finished floor. Remove protective label once construction is
complete. See Fig. 10S
Fig. 9R
Fig. 10R
Fig. 10S
Fig. 9S

EZ1TM CLEANOUT SERIES
EZ1TM FLOOR CLEANOUT INSTALLATION INSTRUCTIONS
Zurn Industries, LLC | Specification Drainage Operation
1801 Pittsburgh Avenue, Erie, PA U.S.A. 16502 · Ph. 855-663-9876, Fax [phone]
In Canada | Zurn Industries Limited
3544 Nashua Drive, Mississauga, Ontario L4V 1L2 · Ph. 905-405-8272, Fax [phone]
www.zurn.com
Rev. C
Date: 02/27/2018
C.N. No. 139680
Form No. CO18 Page 5 of 6
®
For Tile Installation (Steps 11 and 12)
If finished fixture is tilted, See Step 13
Round
11. Adjust head assembly to the height of the finished floor.
See Fig. 11R
12. Install finish flooring per manufacturers instructions.
Remove protective label from cover once construction is
complete.
See Fig. 12R
Square
11a. Adjust head assembly to the height of the finished floor.
See Fig. 11S
11b. Fill in rough-in adapter with cement or grout. Ensure to
completely fill in around entire head assembly flush with
finished concrete.
See Fig. 11S
12. Install finished flooring per manufacturers instructions.
Remove protective label from strainer once construction is
complete.
See Fig. 12S
Fig. 11R
Fig. 12R
Fig. 11S
Fig. 12S

EZ1TM CLEANOUT SERIES
EZ1TM FLOOR CLEANOUT INSTALLATION INSTRUCTIONS
Zurn Industries, LLC | Specification Drainage Operation
1801 Pittsburgh Avenue, Erie, PA U.S.A. 16502 · Ph. 855-663-9876, Fax [phone]
In Canada | Zurn Industries Limited
3544 Nashua Drive, Mississauga, Ontario L4V 1L2 · Ph. 905-405-8272, Fax [phone]
www.zurn.com
Rev. C
Date: 02/27/2018
C.N. No. 139680
Form No. CO18 Page 6 of 6
®
For Correcting a Tilted Cleanout (Steps 13, 14
and 15)
13. Remove cover and cover frame from installed head
assembly.
See Fig. 13
14. A shim set and longer screws are included under the label
of the rough-in cover.
Install shims on shank and adjust/rotate shims as needed
to bring cover level with the finished floor. (Included shims
can adjust for up to 1/4" [6 mm] of tilt. See Fig. 14
15. Reinstall cover frame and cover. Use included longer screws
as needed. Torque screws to 16-18 in-lbs [18.5-20.5 cm-
kg]
Remove protective label from cover once construction is
complete. See Fig. 15a for Slab on Grade Installation and
Fig. 15b for tile installation
Fig. 13
Fig. 14
Fig. 15b
Fig. 15a