360 Vision Vision i Dome Instruction sheet

Vision i Dome_VisionDome VR Installation Manual Ver 3.1 Page 1
© 360 Vision Technology Ltd.
Vision i Dome/VisionDome VR
Installation/Conguration Manual

Vision i Dome_VisionDome VR Installation Manual Ver 3.1 Page 2
© 360 Vision Technology Ltd.
Table of Contents
1 Safety and Precautions .............................................................................................................................. 3
2 Housing Dimensional Drawing ................................................................................................................... 3
3 Bracket Dimensional Drawing .................................................................................................................... 5
4 Connections ............................................................................................................................................... 6
4.1 Standalone Alarmcard Setup ............................................................................................................. 8
5 Basic Twisted Pair/RS485 Data Wiring .................................................................................................... 12
6 Visiondome VR Protocol/Address setup. ................................................................................................. 12
7 VisioniDome ............................................................................................................................................. 13
7.1 Protocol Switch (S2)......................................................................................................................... 13
7.2 Address Switch (S1)......................................................................................................................... 14
8 RS485 Address Settings .......................................................................................................................... 14
9 Vision i Dome OSD ................................................................................................................................. 15
9.1 PIN Number ..................................................................................................................................... 15
10 VisionDome OSD .................................................................................................................................. 16
10.1 PIN Number ................................................................................................................................... 16
11 OSD Operation/Navigation ..................................................................................................................... 17
12 Important - Care of Painted Surfaces..................................................................................................... 19
13 Storage and Handling............................................................................................................................. 19
14 Warranty................................................................................................................................................. 19

Vision i Dome_VisionDome VR Installation Manual Ver 3.1 Page 3
© 360 Vision Technology Ltd.
1 Safety and Precautions
1. Please read these notes before attempting to operate the 360 Vision VisionDome-HD, and keep for future
reference.
2. All servicing and repairs must be handled by 360 Vision Technology.
3. Avoid pointing the camera directly towards a bright light source (sunlight), or expose the camera to intensive
light situations as this may damage the camera pick-up device.
4. Installation should be carried out by suitably qualied personnel, in accordance with local codes of practice
and regulations.
5. 360 Vision Technology Limited accept no liability for any damage caused by incorrect or improper installation.
2 Housing Dimensional Drawing
MUST NOT BE REPRODUCED OR SHOWN TO
DO NOT SCALE
ALL DIMENSIONS IN MM
REMOVE ALL SHARP EDGES
SHEET:
D
C
B
A
D
C
B
A
4
3
2
1
4
3
2
1
A3
DESCRIPTION SCALE:
PERMISSION OF THE AUTHOR.
ANY THIRD PARTY WITHOUT THE DIRECT WRITTEN
C COPYRIGHT PROTECTED AND
THIS DRAWING AND ALL COPIES ARE
PART NUMBER:
0.167 1 OF 2
TOLERANCES:-
X = 0.5
X.X = 0.1
X.XX = 0.05
A3
3rd ANGLE PROJECTION
360 Vision Technology Ltd.
Unit 7, Seymour Court,
Manor Park, Runcorn, Cheshire,
WA7 1SY. United Kingdom.
www.360visiontechnology.com
188
50 (2") GLAND
CLEARANCE
210.0
9 (x4) ON
190.5 (7.5") PCD
203.0
5.0
121.5
5
10
9
9(22)
NAME:
M5727-A
VANDAL INSTALL
SOFFIT MOUNT (CEILING)
ISS DATE REFERENCE
A 220118 FIRST ISSUE
210118
DATE :
K.CRAIK
RELEASED:
APPROVED:
ENGINEER:
- - MATERIAL: FINISH:
SCALE 0.4
SCALE 0.4
SCALE 0.4
M12x1.5P (x3)
CABLE GLAND CONNECTION
(SEALING PLUG SUPPLIED
ON UNUSED CONNECTION)
External Soft
Weight 3.5kg

Vision i Dome_VisionDome VR Installation Manual Ver 3.1 Page 4
© 360 Vision Technology Ltd.
Weight 4kg
MUST NOT BE REPRODUCED OR SHOWN TO
DO NOT SCALE
ALL DIMENSIONS IN MM
REMOVE ALL SHARP EDGES
SHEET:
D
C
B
A
D
C
B
A
4
3
2
1
4
3
2
1
A3
DESCRIPTION SCALE:
PERMISSION OF THE AUTHOR.
ANY THIRD PARTY WITHOUT THE DIRECT WRITTEN
C COPYRIGHT PROTECTED AND
THIS DRAWING AND ALL COPIES ARE
PART NUMBER:
0.167 1 OF 2
TOLERANCES:-
X = 0.5
X.X = 0.1
X.XX = 0.05
A3
3rd ANGLE PROJECTION
360 Vision Technology Ltd.
Unit 7, Seymour Court,
Manor Park, Runcorn, Cheshire,
WA7 1SY. United Kingdom.
www.360visiontechnology.com
125
12
238
188
263
9.5 (x4) ON
101.6 (4" PCD)
10
11
6
20
M12x1.5P (x3)
CABLE GLAND
332
326
NAME:
M5725-A
VANDAL INSTALL
CAST WALL BRACKET
ISS DATE REFERENCE
A 060617 FIRST ISSUE
060617
DATE :
K.CRAIK
RELEASED:
APPROVED:
ENGINEER:
-- MATERIAL: FINISH:
SCALE 0.3
SCALE 0.3
External Wall
Weight 5.5kg
MUST NOT BE REPRODUCED OR SHOWN TO
DO NOT SCALE
ALL DIMENSIONS IN MM
REMOVE ALL SHARP EDGES
SHEET:
D
C
B
A
D
C
B
A
4
3
2
1
4
3
2
1
A3
DESCRIPTION SCALE:
PERMISSION OF THE AUTHOR.
ANY THIRD PARTY WITHOUT THE DIRECT WRITTEN
C COPYRIGHT PROTECTED AND
THIS DRAWING AND ALL COPIES ARE
PART NUMBER:
0.167 1 OF 2
TOLERANCES:-
X = 0.5
X.X = 0.1
X.XX = 0.05
A3
3rd ANGLE PROJECTION
360 Vision Technology Ltd.
Unit 7, Seymour Court,
Manor Park, Runcorn, Cheshire,
WA7 1SY. United Kingdom.
www.360visiontechnology.com
200
357
575
6
125
9.0 (x4) ON
101.6 (4") PCD
9
9
6
10
188
M12x1.5P (x3)
CABLE GLAND
50 GLAND
CLEARANCE
NAME:
M5726-A
VANDAL INSTALL
SWN-NECK BRACKET
ISS DATE REFERENCE
A 060617 FIRST ISSUE
060617
DATE :
K.CRAIK
RELEASED:
APPROVED:
ENGINEER:
-- MATERIAL: FINISH:
SCALE 0.3
SCALE 0.3
External Swan Neck

Vision i Dome_VisionDome VR Installation Manual Ver 3.1 Page 5
© 360 Vision Technology Ltd.
3 Bracket Dimensional Drawing
LOCKING SCREW
TWIST ACRYLIC
ONTO DOME COVER
TWIST CAMERA
ONTO WALL BRACKET
AND SECURE USING
LOCKING SCREW CAMERA COVER
246 mm
Weight: 3.8kg Weight: 1.4kg
Weight: 1.6kg
Internal False Ceiling Internal Pendant
Internal Pole Bracket Internal Wall Bracket
Internal Corner Bracket External Corner Bracket
Weight: 2.2kg
Please use the appropriate xings to suit the weight of the camera housing used.

Vision i Dome_VisionDome VR Installation Manual Ver 3.1 Page 6
© 360 Vision Technology Ltd.
4 Connections
MAINS input
230Vac
L E N
MAINS FUSE
VRVD-PSU
MAINS FUSE = 1.0AF
OUTPUT FUSE
VRVD-PSU
FUSE 1 = 2.5AT
FUSE 2 = 200mAT
VRVD-PSU
180 x 180 x 100mm
Enclosure Dimensions
VRVD-PSU_301117

Vision i Dome_VisionDome VR Installation Manual Ver 3.1 Page 7
© 360 Vision Technology Ltd.
MAINS input
230Vac
L E N
MAINS FUSE
VRVD-XALARM-PSU
MAINS FUSE = 1.0AF
OUTPUT FUSE
VRVD-XALARM-PSU
FUSE 1 = 2.5AT
FUSE 2 = 200mAT
VRVD-XALARM-PSU
180 x 180 x 100mm
Enclosure Dimensions
VRVD-XALARM-PSU_301117

Vision i Dome_VisionDome VR Installation Manual Ver 3.1 Page 8
The VRVD-XALARM-PSU has eight normally open/normally closed (Dilswitch S1, switch 8 on) alarm inputs
on connector CON1 on the alarm PCB. When using normally closed contacts, all un-used alarm inputs must
be connected to alarm in common CON1. Connect switches or volts free relay outputs from PIRs or other
equipment to CON1 connector so that the terminal labelled COM is connected to the appropriate alarm input
(A1 to A8) when the alarm contact is activated. There is also an alarm relay which can be used to activate
alarms on other equipment (DVRs etc.). The alarm relay contacts (Common – ‘C’, Normally Open – ‘NO’ and
Normally Closed – ‘NC’) use connector CON3 on the alarm PCB.
When an alarm is activated, the ALARM PCB will activate the alarm relay output and will send commands to set
the Visiondome to activate ‘alarm mode’. The Visiondome will save the current status (pan, tilt, lens, tour and
mimic) then it will seek the preset which corresponds with the active alarm number.
The alarm will remain active while the alarm input is active. After the alarm input becomes inactive, a 10 second
alarm timer will start. The timer extends the alarm activity until the alarm timer expires. If the alarm input
becomes active again before the timer has expired, the timer resets and will restart again when the alarm input
becomes inactive and a further preset seek command is sent to the Visiondome.
If an alarm is active and a further alarm becomes active, the latest alarm will interrupt the previous alarm. (i.e.
the latest alarm has highest priority) The Visiondome will seek the preset that corresponds with the new alarm.
When the contacts become inactive, the Visiondome will seek the preset that corresponds with the previous
highest priority alarm that is still active. When all alarms inputs are inactive the alarm timer starts. After the timer
expires, the Alarm PCB sends a command to the Visiondome to end the ‘alarm mode’ and the Visiondome will
return to the status position and action that had been saved when rst alarm became active. (Fit a link on the
alarm card CON4 position 7 to disable the automatic return to the pre-alarm status when all alarms and the
alarm time have expired).
When an alarm is active and the Visiondome has automatically selected the appropriate preset, it is possible
to send further commands (i.e. manual control) to the Visiondome which will override the preset which had
previously been automatically selected. Each time an automatic preset seek occurs as described in the previous
paragraph; the manual control will be interrupted.
4.1 Standalone Alarmcard Setup
Alarm Number Preset Number
1 1
2 2
3 3
4 4
Alarm Number Preset Number
5 5
6 6
7 7
8 8
Address (1-7) (Range 1 to 128)
Use Dilswitch to set address same as camera.
(see page 9).
Alarm Input setting
Use Dilswitch pole 8 to set if alarms are N/O or N/C. All
unused N/C contacts to be connected to alarm common.
(see page 9).
RS485 In Connections/LK3 termination
Connect RS485 from controller to CON6.
Power Connections
Connect 24Vac to CON7.
RS485 Out Connections/LK1 termination
Connect RS485 to camera to CON5.
Relay Output (0.5A 125Vac max, 1A 24Vdc max)
Use CON3 for relay output.
Alarm Inputs
Use CON1 for volt free alarm inputs.
Protocol/Alarm settings
Use CON4 to set protocol and camera
alarm behaviour. (see page 9).

Vision i Dome_VisionDome VR Installation Manual Ver 3.1 Page 9
© 360 Vision Technology Ltd.
Dil Switch Settings 1-7
Address 1 to 128 range See below
Dil Switch Settings 8
Normally Open Contacts Off
Normally Closed Contacts (un-used inputs must be connected to common) On
RS485 Address Settings
1 2 3 4 5 6 7 8
ON
Example shows switch
settings for camera address 3
Switch is shown as
white.
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON

Vision i Dome_VisionDome VR Installation Manual Ver 3.1 Page 10
© 360 Vision Technology Ltd.
Suitable cables
Cable Size
0.75mm² 30 metres
Visiondome VR
Maximum Distances
(Using VRVD-PSU)
Power
75 metres
Internal Visiondome
Maximum Distances
(Using VDI-PSU)
1.00mm² 40 metres
100 metres
1.25mm² 50 metres
125 metres
1.50mm² 60 metres
150 metres
2.00mm² 100 metres
250 metres
To ensure optimum Visiondome performance these parameters must be adhered to. Failure to do so will
invalidate the warranty.
1 2 3 4 5 6 7 8
CON4
Protocol Settings 3 4 5 6
360 Vision Off Off Off Off
Pelco D 9600 baud On Off Off Off
Pelco D 4800 baud Off On Off Off
Pelco D 2400 baud On On Off Off
Pelco P 9600 baud Off Off On Off
Pelco P 4800 baud On Off On Off
Pelco P 2400 baud Off On On Off
CON4 Settings

Vision i Dome_VisionDome VR Installation Manual Ver 3.1 Page 11
© 360 Vision Technology Ltd.
Internal Vision i Dome/VisionDome Connections
The connection board is located at the top of the dome.
Coax Video Connection board
Power Connections
Connect 24Vac to CON2.
Data Connections
Connect RS485 (D+/D-) to Dome connection board using CON3.
Video Connections
Connect Video Coax cable (Video/Gnd) to Dome connection board
using CON4.
Active Balun Twisted Pair Video Board
(Screw Terminal version)
Power Connections
Connect 24Vac to CON4.
Data Connections
Connect RS485 (D+/D-) to Dome connection board using CON8.
Video Connections
Connect Twisted Pair Video Signal cable (V+/V-) to Dome
connection board using screw terminal CON5. A Twisted Pair Video
balun is required to suit cable length to receive video signal.
Active Balun Twisted Pair Video Board
(RJ45 Connector version)
Power Connections (if Required)
Connect 24Vac to CON4.
LK1 & LK2 can be used to switch power into the camera from the
RJ45 (CON3) to the two way screw connector (CON4).
Power, Video & Data Connections
Connect cable to RJ45 CON3. (Twisted Pair Video Signal Only). A
Twisted Pair Video balun is required to suit cable length to receive
video signal. Wiring/connection diagram shown below.
RJ45 CAT5, CAT5e, CAT6 Cable Signal
Pin 1 White with Orange Band Video +
Pin 2 Orange Video -
Pin 3 White with Green Band RS485 D+
Pin 4 Blue AC+
Pin 5 White with Blue Band AC+
Pin 6 Green RS485 D-
Pin 7 White with Brown Band AC-
Pin 8 Brown AC-
RJ45 CON3 Connections
A Twisted Pair Video balun is required to suit cable length to receive video signal.

Vision i Dome_VisionDome VR Installation Manual Ver 3.1 Page 12
© 360 Vision Technology Ltd.
5 Basic Twisted Pair/RS485 Data Wiring
The Vision i Dome and VisionDome are capable of being controlled by either Coax Telemetry or Twisted Pair
Telemetry (RS485). Below are wiring congurations for two wiring formats used for Twisted Pair Telemetry
(RS485). The Visiondome VR camera is not RS485 end of line terminated, a 120Ω resistor across D+ and D-
must be used if the camera is tted at the end of the RS485.
Daisy Chain
RS485 twisted pair cable is wired to each camera in a “chain”. Only
the last camera is to have the RS485 (end of line) termination on, all
other cameras in the chain must have the RS485 termination off. See
Section 7 for the relevant product, termination switch settings.
Star Wired
RS485 twisted pair cable is wired to each camera in a “star” from one
point. A RS485 star driver/data distribution product must be used. All
cameras in this wiring conguration must have the RS485 (end of
line) termination on. See Section 7 for the relevant product, termina-
tion switch settings.
6 Visiondome VR Protocol/Address setup.
All Visiondome VR cameras are supplied set to 360 Vision protocol, camera twisted pair address 1. When
the Visiondome VR is switched on, an OSD (On Screen Display) is shown on the image from the camera for
approx 20 seconds.
PRO:360VTL CAM:0001 S
Visiondome VR Software Version
PRO: Protocol being used for telemetry (e.g. 360 Vision Technology Ltd)
CAM: Camera RS485 ID (e.g. Cam 1)
S or L: Short or Long cable run. Use the utility to set whether the coax used to send video is under or over
300m.
Second Line: Shows the Visiondome VR Software Version loaded into the camera.
To change the above settings in the camera, 360 Predator utility software, a USB/RS485 cable (PRED-
USB-485) and a laptop are required.
The Predator utility and PRED-USB-485 cable drivers can be found on the CD (shipped with the camera) or on
the 360 Vision Technology web site (www.360visiontechnology.com/downloads).
Install the software (Predator-issued-120521-1-installer.exe) on the laptop being used. Connect the RS485 end
of the cable tted with a 3 way connector to the Visiondome VR RS485. Run the utility on the laptop and then
connect the USB end of the cable into the laptop. The utility will then look for new comms ports and then will
look for the camera across all baud rates used.
Settings that can be altered from this software are:
• Protocol: 360 (Coax/RS485), Pelco P 2400/4800/9600, Pelco
D 2400/4800/9600, Pelco Coaxitron (Extended version), VCL
(Coax/RS485), Ultrak (RS485), Forward Vision (RS485), BBV/
DENNARD C (FSK Coax), MARK MERCER (FSK Coax),
Molynx (RS485)
• Coax Cable length: Longer than 300m or shorter than 300m.
• RS485 Address: Used on RS485 systems only.

Vision i Dome_VisionDome VR Installation Manual Ver 3.1 Page 13
© 360 Vision Technology Ltd.
7 VisioniDome
7.1 Protocol Switch (S2)
Dil Switch Settings 1
Not used Off
Not used On
Dil Switch Settings 2
RS485 Termination Off (Not last camera in chain) Off
RS485 Termination On (Last camera in chain) On
Dil Switch Settings 3 4 5 6
360 Vision (Coax or RS485) Off Off Off Off
Pelco D 9600 baud (or Coaxitron Extended) On Off Off Off
Pelco D 4800 baud (or Coaxitron Extended) Off On Off Off
Pelco D 2400 baud (or Coaxitron Extended) On On Off Off
Pelco P 9600 baud (or Coaxitron Extended) Off Off On Off
Pelco P 4800 baud (or Coaxitron Extended) On Off On Off
Pelco P 2400 baud (or Coaxitron Extended) Off On On Off
BBV/Dennard (FSK Coax) Off Off Off On
Mark Mercer (FSK Coax) On Off Off On
Ultrak (RS485) On On Off On
VCL (Coax or RS485) On On On Off
Forward Vision Off Off On On
Molynx (Coax) On Off On On
Dil Switch Settings 7
Not used Off
Not used On
Dil Switch Settings 8
Not used Off
Not used On
1 2 3 4 5 6 7 8
ON
Example shows switch
settings for
RS485 termination On,
360 Vision Protocol,
Switch is shown as
white.

Vision i Dome_VisionDome VR Installation Manual Ver 3.1 Page 14
© 360 Vision Technology Ltd.
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
Example shows switch
settings for camera address 3
Switch is shown as
white.
7.2 Address Switch (S1)
Dil Switch Settings 1-8
Dome Address 1 to 256 range See below
8 RS485 Address Settings
Use S1 on the VisionDome for addressing.
Use S2 on the Vision i Dome for addressing (Limited to 128).

Vision i Dome_VisionDome VR Installation Manual Ver 3.1 Page 15
© 360 Vision Technology Ltd.
Vision i Dome Conguration
9 Vision i Dome OSD
OSD (On Screen Display) is accessed by dening/programming preset 6 or 95.
• Use the joystick up, down, left and right to navigate the menu. • Use the joystick zoom in to highlight/select an option. • Use joystick left and right to increment/decrement numbers.
Tour 001 item ...
PreDelSpd
Old................. New................ 0 1 2 3 4 5 6 7 8 9 Accept Item Accept Final Item Clear Item Return Exit
DEFINE MIMIC
Mimic Number 001 Start Recording Return Exit
DEFINE PRESET
Preset Number ... 0 1 2 3 4 5 6 7 8 9 Accept Entry Clear Entry Return Exit
DEFINE HOME FUNCTION
Action Tour Number 001 Delay Minutes 010 Delay Seconds 000 Accept Changes Return
General 1 General 2
SERVICING
Power Reset Dome Factory Reset Dome Dome Software Version Return Exit
Dene Tour Dene Mimic Dene Preset Dene Home Function Return
Dene Tour Dene Mimic Dene Preset Dene Home Function Settings Menu Servicing Return
SEEK PRESET
Preset Number ... 0 1 2 3 4 5 6 7 8 9 Accept Entry Clear Entry Return Exit
START TOUR
Tour Number 001 Start Tour Return Exit
START MIMIC
Mimic Number 001 Start Mimic Return Exit
DOME SETTINGS MENU
Pin Number ... 0 1 2 3 4 5 6 7 8 9 Accept Entry Clear Entry Return Exit
DOME MENU
Seek Preset Start Tour Start Mimic Settings Menu Exit
WARNING
All Stored Data Will Be Permanently Erased Continue Return Exit
FINISH MIMIC BY
DEFINING ANY PRESET
9.1 PIN Number Operators PIN: 360 or 426 or 180 Controllers PIN: 1379 or 9731 Engineers PIN: 5498
Auto Flip OFF Proportional OFF AF AI When PTZ ON Zoom Speed 008 OSD Preset 6 YES Accept Changes Return
Digital Zoom ON White Balance AUTO Accept Changes Return

Vision i Dome_VisionDome VR Installation Manual Ver 3.1 Page 16
10 VisionDome OSD
OSD (On Screen Display) is accessed by dening/programming preset 6 or 95.
• Use the joystick up, down, left and right to navigate the menu. • Use the joystick zoom in to highlight/select an option. • Use joystick left and right to increment/decrement numbers.
10.1 PIN Number
Operators PIN: 360 or 426 or 180 Controllers PIN: 1379 or 9731 Engineers PIN: 5498
VisionDome VR Conguration
Tour 001 item ...
PreDelSpd
Old................. New................ 0 1 2 3 4 5 6 7 8 9 Accept Item Accept Final Item Clear item Return Exit
DEFINE MIMIC
Mimic Number 001 Start Recording Return Exit
DEFINE PRESET
Preset Number ... 0 1 2 3 4 5 6 7 8 9 Accept Entry Clear Entry Return Exit
DEFINE HOME FUNCTION
Action Tour Number 001 Delay Minutes 010 Delay Seconds 000 Accept Changes Return
PRIVACY ZONE MENU
Dene Privacy Zone Seek Privacy Zone Remove Privacy Zone Return Exit
SERVICING
Power Reset Dome Factory Reset Dome Predator Software Version Return Exit
Dene Tour Dene Mimic Dene Preset Dene Home Function Return
Dene Tour Dene Mimic Dene Preset Dene Home Function Settings Menu Text Field Menu Servicing Privacy Zone Menu Return
SEEK PRESET
Preset Number ... 0 1 2 3 4 5 6 7 8 9 Accept Entry Clear Entry Return Exit
START TOUR
Tour Number 001 Start Tour Return Exit
START MIMIC
Mimic Number 001 Start Mimic Return Exit
DOME SETTINGS MENU
Pin Number ... 0 1 2 3 4 5 6 7 8 9 Accept Entry Clear Entry Return Exit
DOME MENU
Seek Preset Start Tour Start Mimic Settings Menu Exit
TEXT FIELD EDIT
---------------------------------------
0123456789 :ABCDEFG HIJKLMNOPQRSTUVWXYZ
X Position: 000 Y Position: 000 TEXT Display: OFF Accept Entry Clear Entry Return
General Settings Night Settings Shutter Settings Return
WARNING
All Stored Data Will Be Permanently Erased Continue Return Exit
DEFINE PRIVACY ZONE
Privacy Zone ... 0 1 2 3 4 5 6 7 8 9 Accept Entry Clear Entry Return Exit
SEEK PRIVACY ZONE
Privacy Zone ... 0 1 2 3 4 5 6 7 8 9 Accept Entry Clear Entry Return Exit
REMOVE PRIVACY ZONE
Privacy Zone ... 0 1 2 3 4 5 6 7 8 9 Accept Entry Clear Entry Return Exit
FINISH MIMIC BY
DEFINING ANY PRESET
Controller level Engineer level
Digital Zoom ON White Balance OUTDOOR Line Lock ON Line Phase +056 Video Gain 002 Video Lift 000 Wide Dynamic OFF Accept Changes Return
Auto Flip SEMI Proportional OFF Freeze Presets ON Zoom Speed 007 OSD Preset Six YES
AF AI When PTZ ON
Accept Changes Return
Col/Mono Change: Dark Mono On 020 Mono Off 013 1=day 7=dusk 20=dark Bright Control Normal Noise Reduction 0 Aperture 3 Accept Changes Return
Fast Shutter OFF Fast Shutter Speed g:1/1000 Slow Shutter 1/3 sec Accept Changes Return
General1 Settings General2 Settings Return
Shutter
NightGeneral
General 1 General 2

Vision i Dome_VisionDome VR Installation Manual Ver 3.1 Page 17
11 OSD Operation/Navigation
Dome menu
• Seek Preset
• Start Tour
• Start Mimic
• Settings Menu
Dene Tour
A tour of presets is stored in the VisionDome as a list of tour points. Each tour point consists of a preset number,
the dwell time for which the VisionDome will pause and the speed parameter that will be used to seek the
preset. Each of the four tours of presets can contain between 2 and 360 points.
When programming a tour of presets it is necessary to rst store all the required presets into the VisionDome
and to dene the required dwell times and speeds of travel that you will require the VisionDome to use when the
tour is started.
A maximum of four individual tours of presets can be stored in each VisionDome. Each tour can have between
2 and 360 points, each point can be a preset in the range 1 to 360 (36 presets for the Vision i Dome). Different
points can use any preset number, including repeats of ones that have been used before. The speed that the
camera will travel at to reach the preset can be in the range 1°/sec (slowest) to 100°/sec (fastest). To seek the
preset at maximum speed, set speed to 0. The delay (dwell) at each point is dened in seconds, range 1 to 100.
This page will open on Tour 1, use the joystick left and right to change to another tour. To add item 1, use the
joystick to tilt down. This will highlight the number line so that the tour can be programmed. Use the joystick to
navigate along the number line and zoom in to select the number. This will add the number in to the NEW tour.
Add in the gures for the item/point in the tour using the sequence labelled above (PREDELSPD. PRE is preset
position, DEL is delay in seconds and SPD is speed at °/second). This is how the camera will be programmed to
move to a preset for a period of time at a set speed. All nine gures must be added into the item. Figures must
be added in three i.e. preset 21 will be added as 021.
Example of an item/point
021005100 = Move to preset 21 for 5 seconds at 100°/sec
Highlight ACCEPT ITEM and zoom in, this will add the item/point into the tour. The OLD item/point will be shown
on the screen. If these settings are acceptable, highlight the ACCEPT ITEM option and zoom in. There is no
need to add in these points again. Keep adding points until the tour is complete. On the nal item/point of the
tour highlight and zoom in on ACCEPT FINAL ITEM. This will complete the tour programming.
Dene Mimic
When a mimic tour is started, the VisionDome will perform all the actions which were dened when the mimic
was programmed. Up to four mimic tours can be dened.
Before going into the OSD screen to programme a Mimic tour it is recommended to move the camera in to the
start position, any movement or delay will be recorded once the recording has started.
Highlight and zoom in on START RECORDING, this will allow a mimic tour to be programmed into the camera.
The mimic tour can then be used to playback any manual movement, preset seek or delay. Program a preset to
end the mimic tour program.
Dene Preset
Before going into the OSD screen to programme a preset, the camera must be in the position required. Once in
the OSD you cannot manually move the camera.
Dene Home Function
The camera will perform an ACTION (goto preset, start preset or mimic tour), after a period of inactivity. Use the
NUMBER option to set which preset or tour to start, and the DELAY MINUTES/SECONDS to input the inactivity
time period.
Settings Menu
General Settings

Vision i Dome_VisionDome VR Installation Manual Ver 3.1 Page 18
© 360 Vision Technology Ltd.
General 1
• Digital Zoom - Use this option to enable or disable digital zoom.
• White Balance - Change the camera white balance settings to suit the area.
• Line Lock - (Not available on Vision i Dome) Used to line lock the camera.
• Line Phase - (Not available on Vision i Dome) Can be used to manually adjust the line phase.
• Video Gain - (Not available on Vision i Dome) Used to adjust the video level to suit different lengths of
coax cable.
• Video Lift - (Not available on Vision i Dome) Used to adjust the frequency of the video level to suit
different lengths of coax cable.
• Wide Dynamic - (Not available on Vision i Dome) Enable WDR. Options available are ON, Auto and
Off. Default is off.
General 2
• Auto Flip - Use this option to set how the camera behaves when full tilt down is reached.
Semi - Requires a second tilt down command, when at full tilt down to spin camera 180°.
Full - Automatically spins the camera 180°
• Proportional - Automatically reduces/increases pan/tilt speed depending on zoom ratio.
• Freeze Presets - (Not available on Vision i Dome) This option freezes the image, when moving
between presets.
• Zoom Speed - Use to set preferred zoom speed, 5 is slow and 8 is fast.
• OSD Preset Six - Go into OSD using preset 95 and you can switch off OSD access using preset 6.
• AF AI When PTZ - Auto focus/iris will activate when PTZ is used, can be switched off. Default is on.
Night (Not available on Vision i Dome)
• Col/Mono Change - Col/Mono level settings can be changed to suit the site requirements. Options
are dark, medium and light. Default is dark. This sets when the camera goes into ‘mono mode’.
• Mono On - Range is 7 to 25. A lower value will set the level on when the scene is brighter, a higher
value will set the level on when the scene is darker.
• Mono Off - Range is 1 to 20. A lower value will set the level off when the scene is brighter, a higher
value will set the level off when the scene is darker.
• Bright Control - Options are automatic or normal.
• Noise Reduction - Used to reduce noise with scenes of low illumination. NR must be set to suit the
environment. Default is off.
• Aperture - Can be used to increase the picture detail. Default is 3.
Shutter
• Fast Shutter - Option to enable fast shutter and set speed of the shutter.
• Slow Shutter - Option to alter the slow shutter speed. Altering this gure will have an effect on the low
light capabilities of the camera.
Text Field Menu (Not available on Vision i Dome)
Navigate along alpha-numeric characters and use zoom in to select. Choose text position by inputting x and y
co-ordinates. Set text display to on, if required.
Servicing
• Power Reset - This will reboot the camera, no settings will be lost.
• Factory Reset - This will reboot the camera and all the settings will be lost.
• Dome Software Version - This shows the software version of the camera.

Vision i Dome_VisionDome VR Installation Manual Ver 3.1 Page 19
© 360 Vision Technology Ltd.
Privacy Zone Menu (Not available on Vision i Dome)
Can be used to obscure a scene within an image e.g. private residence. Move the camera to the position
required for the privacy zone before going into the camera OSD. You cannot manually move the camera once
in the OSD. Use the zoom to set the size of the privacy zone. Privacy zone will cover the whole scene viewed
when set.
• Dene Privacy Zone - Used to set a privacy zone.
• Seek Privacy Zone - Used to seek a privacy zone.
• Remove Privacy Zone - Used to remove a privacy zone.
12 Important - Care of Painted Surfaces
The powder coating applied to the VisionDome external housing is recognised as being in the forefront for
quality and nish. However, in order to preserve the aesthetic nish it is recommended that the coating is
regularly cleaned.
Regular cleaning on a maximum three month interval, using warm and mild detergent must be undertaken.
Abrasive cleaners including strong solvent must NOT be used at any time.
In areas where the coating may come in contact with concentrated atmospheric pollutants [marine, chemical
and especially bird droppings] it would be prudent to clean more frequently e.g. monthly.
Full documentation of the cleaning schedule MUST be maintained to ensure that a warranty claim can be
considered.
If damage occurs to the coating (e.g. the VisionDome is dropped, scrapped etc), repairs MUST be carried out
immediately.
When the VisionDome is installed in areas where there is a high risk of damage from birds or their droppings,
additional precautions and measures should be used to keep the birds away from the VisionDome e.g. t anti-
bird spikes.
13 Storage and Handling
Visiondomes should be handled with care and must not be dropped. When Visiondomes are inside the transit
packaging which is used for despatch from the factory, they should not be stacked to a height of more than two
Visiondomes.
When Visiondomes are being stored before installation they should be kept in the transit packaging and located
in a dry indoor environment preferably between 1°C and 35°C which is dry and dust free. Humidity should such
that water vapour is non-condensing. Visiondomes can be allowed to be outside this range for short periods
of time (24 hours maximum) for transport (e.g. in aircraft or vans) but must never be allowed to be outside the
normal operating temperature range of -40°C to +60°C even during storage.
Before installation the Visiondome should be clean and dry. (If necessary it should be cleaned and dried taking
care that the cover is not scratched).
14 Warranty
This information and/or any technical information – whether received verbally or writing – is given in good faith
but without warranty and this also applies where proprietary rights of third parties are involved. The information
provided does not release you from your obligation to check its validity and to test the products suitability for
the intended purpose(s) and use(s). The application, use and installation of the products either in isolation or in
conjunction with other products used, provided and installed by you on the basis of the technical advice issued
are beyond our control and therefore remain entirely your own responsibility.
©2018 ALL DESIGNS AND SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE

Vision i Dome_VisionDome VR Installation Manual Ver 3.1 Page 20
© 360 Vision Technology Ltd.