360 BANDIT GREAT PLAINS User manual

360YIELDCENTER.COM
360 BANDIT™
INSTALLATION INSTRUCTIONS
GREAT PLAINS MODELS
� � �
5.26.20 � V4
360 BANDIT360 BANDIT
������
All trademarks are the property of 360 Yield Center, its ailiates and/or its licensors. ©2019 360 Yield Center. All rights reserved.
FOR QUESTIONS PLEASE CONTACT OUR
PRODUCT SUPPORT TEAM AT 309-300-3120

INSTALLATION INSTRUCTIONS
GREAT PLAINS
Using one of the long bolts 3and one of the short bolts 4
from the provided hardware kit, attach the 360 BANDIT
unit (long leg to the rear) to the row unit where the closing
system casting was just removed. The longer bolt will be
used in the front hole and the shorter bolt will be used in
the rear hold.
Tighten with 16 mm socket. Torque bolts to 42.2 ft lbs.
Ensure not to over tighten bolts.
Hammer/Mallet
Wrench Sizes: 15/16” and 7/16”
Socket Sizes: 16mm, 15/16”, 18mm and 7/16”
Impact
Torque Wrench
Release spring 1to remove tension from closing system.
NOTE: If the optional chains kit is not being installed do not
remove the closing wheels.
If present, remove insecticide attachment.
Using an 3/4” socket remove the two bolts that attach
the closing system casting 2to the row unit and set the
closing system casting aside. Bolts can be discarded.
1
3
BEFORE YOU BEGIN...
HELPFUL TOOLS
STEP 1
REMOVE CLOSING SYSTEM
STEP 2
INSTALL BANDIT UNIT
PAGE 2
4
24

Using two remaining bolts and washers reinstall the closing
system to the BANDIT unit 15 . Secure with nut.
Torque bolts to 42.2 ft lbs. Ensure not to over tighten bolts.
Reinstall insecticide attachment, if present.
Insert 5/8” X 3” bolt 8through the disk 9. Place small
shim washer then fender washer over the bolt. Insert
bushing 10 (large side first) and hose guide assembly 11 (ear
tab 12 facing in).
Slide bolt of the disk assembly into the lower hole on the
bandit 13 , aligning the ear tab 12 with corresponding upper
hole and secure with lock nut.
Tighten with 15/16” socket and wrench. Check to ensure
that the disk freely turns. If the disk does not freely turn,
back o the lock nut slightly until the disk freely turns.
Repeat for other side.
Route application hoses through hole in top of 360 BANDIT
frame 14 .
Using a mallet, install provided dust caps over disk bolt
heads.
Using side-cutters, cut the two hose guides apart 5.
Route the hose through the top two holes in the hose guide 6.
Hose guides are labeled “ L” left and “R” right 7.
NOTE: When installing hoseguides on the row unit, left
and right are determined from the operators seat.
INSTALLATION INSTRUCTIONS
GREAT PLAINS
STEP 3
PREPARE HOSE GUIDES
STEP 4
INSTALL DISK ASSEMBLY
STEP 5
REINSTALL CLOSING SYSTEM
PAGE 3
5
CUT
7
5
6
8
910 11 12
13
12
14
15

PLUMBING RECOMMENDATIONS:
To prevent excess fertilizer from dribbling out of the hoses
when product application is shut o, install one push to
connect polypropylene (Inlet x Outlet) 3/8” O.D. check valve
(not included) in the plumbing to each row prior to the 360
BANDIT orifices. Check valve is available at Dultmeier Sales
(Item #BUCV1103-P38).
A 50 mesh strainer (not included) can be used in the
complete plumbing system between tanks and 360
BANDIT to help prevent debris from blocking orifices.
16
17
18
19
Install orifice plates 16 in the rubber grommets 17 .
Assemble pluming components in the arrangement shown
above 18 .
Attach the plumbing assembly to each of the hoses coming
from the house guides 19 .
NOTE: If hoses are not fully seated in the push to connect,
they will leak. Hoses seat 7/8” of an inch deep or until you
hear a snap.
The supplied push to connect adapter in the 360 BANDIT
kit connects to 3/8” push to connect compatible hose.
Secure hoses to row unit with provided zip ties.
INSTALLATION INSTRUCTIONS
GREAT PLAINS
STEP 6
ASSEMBLE PLUMBING
INSTALLATION COMPLETE
PAGE 4
19