3M Speedglas 9100-Air Maintenance manual

53 21 00
16 90 05
50 28 00
53 41 0053 37 00
53 35 05
53 61 00
53 62 00
53 60 00
53 30 00
79 01 01
16 95 02
16 95 05
16 95 50
3M™Speedglas™Welding Helmet 9100 Air
To optimise the effective lifetime of your welding equipment and avoid the additional cost of replacement, regular
maintenance is important. Replace all damaged parts immediately to ensure correct levels of protection.
• Helmet and head harness. Inspect for cracks or any
damaged or defective parts. Replace if needed.
• Cover lenses. To provide the best possible
vision they should be clean and without scratches.
• Face seal. If the face seal is damaged there is a great
risk that contaminated air will get inside the helmet.
Verify it’s in position and free from splits and tears.
• Welding lens. Ensure low battery is not flashing
and check that the sensors are clean and uncovered.
• Breathing tube. Confirm tube is not damaged or
leaking any air. To extend the life of breathing tube,
use a tube cover or a heavy-duty rubber tube.
Before use After use
• Clean the helmet. Wipe with a moist tissue or cloth,
both inside and outside the helmet. If you suspect that the inside
of the airduct is dirty, it must be changed.
DO NOT rinse, immerse in water or clean with solvents.
• Face seal and sweatband. Remove for additional cleaning as needed
and replace if they become unhygienic.
• Cover lenses. Clean with a soft cloth and replace if any pits or
scratches occur.
• Breathing tube. Replace if damaged, deformed or leaking any air.
• Storage. Store the helmet in a dry, clean area away from direct
sunlight, high temperatures and solvents.
Care & Maintenance
To request a quote or place an order for spare parts, please contact TWS on [phone] or visit www.tweld.com.au. Please note that higher than normal levels
of pollutants, heat and sparks will require more frequent replacement of components. If you require additional guidance, please check the care and maintenance videos on our
YouTube Channel (www.youtube.com/user/3MSpeedglas) or contact your local TWS representative.
Further information and advice
Authorised 3M Wholesaler
Unit 13, 39 Herbert Street • St Leonards NSW 2065 • Australia
T: [phone] • F: [phone]
E: [e-mail]
W: www.speedglas.com.au
171021
171022
171023
171024
422000
500026
502800
526000
527000
527070
528025
531000
532100
533000
533505
533700
534100
536000
536100
536200
790101
HEAD PROTECTION 9100
THROAT PROTECTION 9100
HEAD CAPE TECAWELD
SWEATBAND 9100 & 9100 FX PK=2
SWEATBAND 9100 & 9100 FX PK=5
SWEATBAND 9100 & 9100 FX PK=50
LENS MAGNIFYING 1.0X 9100 100 & 9000
LENS MAGNIFYING 1.5X 9100 100 & 9000
LENS MAGNIFYING 2.0X 9100 100 & 9000
LENS MAGNIFYING 2.5X 9100 100 & 9000
LENS MAGNIFYING 3.0X 9100 100 & 9000
BATTERY LITHIUM 9100, 100 & 9000 PK=2
LENS WELDING 9100XXi SPEEDGLAS
HELMET WELDING 9100 AIR EXC LENS
LENS COVER OUTER STD 9100 PK=10
COVER LENS OUTER HC 9100 PK=10
LENS COVER OUTER HT 9100 PK=10
LENS COVER INNER 9100XX PK=5
HOLDER BATTERY 9100
COVER FRONT SILVER 9100XXi
HEAD HARNESS 9100
ADAPTOR ADFLO BREATHING TUBE 9100 AIR
AIR DUCT BACK PART 9100 AIR
FACE SEAL 9100 AIR
HEAD HARNESS PIVOT MECHANISM 9100
HEAD HARNESS FRONT PART 9100
HEAD HARNESS BACK PART 9100
CARRY BAG SPEEDGLAS
Part No
169005
169010
169100
169502
169505
169550
171020
Description Part No Description Part No Description Part No Description
17 10 20
17 10 21
17 10 22
17 10 23
17 10 24
50 00 26
52 60 00
52 70 00
52 70 70
53 10 00
42 20 00
16 91 00
52 80 25
16 90 10

3M™Adflo™Powered Air Respirator
To optimise the effective lifetime of your welding equipment and avoid the additional cost of replacement, regular
maintenance is important. Replace all damaged parts immediately to ensure correct levels of protection.
• Battery. Ensure that it’s adequately charged and fitted
correctly.
• Motor Body. Inspect the unit for damage and ensure it’s
firmly fixed to the belt. Ensure filters are correctly fitted.
• Breathing tube. Inspect the tube and connections
to ensure they are free from splits and holes.
Replace if damaged, deformed or leaking any air.
To extend the life of the breathing tube, use a tube cover
or the heavy-duty rubber breathing tube.
• Air flow check. Fit the breathing tube to the unit and
attach the airflow meter in the other end of the tube and
switch on the Adflo PAPR. If the ball does not rise above
the line, continue fault finding.
• Alarm check. Cover the air outlet of the airflow
meter with your hand until an audible warning is heard
and the red indicator illuminates. Remove your hand.
The alarm should now stop.
834017
834018
835000
835005
836000
836010
837010
837110
837120
837242
837542
837620
837621
837630
837631
837730
837731
838031
ADAPTOR ADFLO BREATHING TUBE 9100 FX AIR
ADAPTOR QRS BREATHING TUBE TO 9000
PAPR MOTOR WITH HOUSING ADFLO
CHARGER BATTERY NIMH ADFLO
CHARGER BATTERY LI-ION ADFLO
BATTERY MULTI-STATION ADFLO
TUBE BREATHING SELF ADJUSTING QRS ADFLO
TUBE BREATHING HEAVY DUTY RUBBER QRS ADFLO
TUBE BREATHING COVER FLAME RESISTANT ADFLO
BELT ADFLO
BELT EXTENSION ADFLO
SPARK ARRESTOR ADFLO
PRE-FILTER ADFLO PK=5
FILTER PARTICLE PSL ADFLO
FILTER ODOUR ADFLO
FILTER ODOUR REPLACEMENT PAD ADFLO
FILTER NUIS LEVEL ORGANIC VAPOUR/ACID GAS
ADFLO FILTER GAS A1 ADFLO
BATTERY STANDARD NIMH ADFLO
BATTERY HEAVY DUTY NIMH ADFLO
BATTERY STANDARD LI-ION ADFLO
BATTERY HEAVY DUTY LI-ION ADFLO
RESPIRATOR STANDARD LI-ION ADFLO
RESPIRATOR HEAVY DUTY LI-ION ADFLO
FILTER COVER LI-ION ADFLO
Part No
Before use After use
• Clean the equipment. Wipe the motor body with a moist tissue or
cloth. If you suspect that the inside of the breathing tube is dirty,
it must be changed.
DO NOT rinse, immerse in water or clean with solvents.
DO NOT attempt to remove contamination of filters as this will damage
the filters and void the warranty.
• Replace damaged parts. Replace all damaged parts to guarantee the
proper functioning of the respirator. Worn out components should be
disposed of according to local regulations.
• Spark arrestor. Replace if deformed and no longer fitting well.
• Prefilter. Replace regularly to extend the life of the particle
filter. This will save money and also extend the battery run-time.
• Particle filter. Check the filter indicator position and replace if
the red LED is lit. Otherwise, replace whenever the battery operating
time becomes too short, or when “fully loaded” filter triggers low
airflow alarm.
• Gas filter. Replace the gas filter according to your work place
requirements. Do not wait until you can sense odours or smells.
• Odour filter. Replace any time you smell unpleasant odours.
Odour filter is not required if gas filter is used.
• Storage. Put the battery/turbo unit on charge after use. When stored,
recharge every six months. Store the unit in a dry, clean area away
from direct sunlight, high temperatures and solvents. For example use
the Adflo storage bag.
To request a quote or place an order for spare parts, please contact TWS on [phone] or visit www.tweld.com.au. Please note that higher than normal levels
of pollutants, heat and sparks will require more frequent replacement of components. If you require additional guidance, please check the care and maintenance videos on our
YouTube Channel (www.youtube.com/user/3MSpeedglas) or contact your local TWS representative.
Further information and advice
Care & Maintenance
533505
533506
832000
833101
833111
833709
834016
Description Part No Description Part No Description Part No Description
Authorised 3M Wholesaler
Unit 13, 39 Herbert Street • St Leonards NSW 2065 • Australia
T: [phone] • F: [phone]
E: [e-mail]
W: www.speedglas.com.au
83 80 30 83 60 00
83 60 10
83 60 80
83 70 10
83 70 80
83 50 00
83 50 10 83 31 01
83 25 30
83 76 20 83 80 20
83 71 20
83 71 10
83 72 42
83 20 00 83 76 21
83 32 09
83 40 16
83 40 17
83 75 42
83 50 05
83 40 18
53 35 06
83 76 31
83 76 20
83 76 21
83 80 31 83 76 30 83 31 11
83 77 30
83 31 01
83 80 30 83 60 00
83 60 10
83 60 80
83 70 10
83 70 80
83 50 00
83 50 10 83 31 01
83 25 30
83 76 20 83 80 20
83 71 20
83 71 10
83 72 42
83 20 00 83 76 21
83 32 09
83 40 16
83 40 17
83 75 42
83 50 05
83 40 18
53 35 06
53 35 05
* Speedglas 9000 headtop breathing tubes.