3M Speedglas 9100 FX Series Maintenance manual

3M™Speedglas™Welding Helmet 9100 FX Air
To optimise the effective lifetime of your welding equipment and avoid the additional cost of replacement, regular
maintenance is important. Replace all damaged parts immediately to ensure correct levels of protection.
• Helmet and head harness. Inspect for cracks or
any damaged or defective parts. Replace if needed.
• Cover lenses and visor. To provide the best possible vision
they should be clean and without scratches.
• Face seal. If the face seal is damaged there is a great
risk that contaminated air will get inside the helmet.
Verify it’s in position and free from splits and tears.
• Welding lens. Ensure low battery is not flashing
and check that the sensors are clean and uncovered.
• Breathing tube. Confirm tube is not damaged or
leaking any air. To extend the life of breathing tube,
use a tube cover or a heavy-duty rubber tube.
Before use After use
• Clean the helmet. Wipe with a moist tissue or cloth, both inside and
outside the helmet. If you suspect that the inside of the airduct is dirty,
it must be changed.
DO NOT rinse, immerse in water or clean with solvents.
• Face seal and sweatband. Remove for additional cleaning
as needed and replace if they become unhygienic.
• Cover lenses and visor plate. Clean with a soft cloth
and replace if any pits or scratches occur.
• Breathing tube. Replace if damaged, deformed or leaking any air.
• Storage. Store the helmet in a dry, clean area away from direct
sunlight, high temperatures and solvents.
54 28 00
53 10 00
42 20 00
16 91 00
52 80 25
50 00 26
52 60 00
52 70 00
52 70 70
16 90 10
16 90 07
17 10 20
17 10 21
17 10 22
17 10 23
17 10 24
16 90 06
53 61 00
53 62 00
53 60 00
53 30 00 53 50 00
53 35 00
52 30 00
52 30 01
54 05 00 53 20 16
53 40 00
Care & Maintenance
171020
171021
171022
171023
171024
422000
500026
523000
523001
526000
527000
527070
528025
531000
532016
533000
533500
533505
534000
535000
536000
536100
536200
540500
542800
790101
HEAD COVER SMALL 9100 FX
HEAD COVER LARGE 9100 FX
THROAT PROTECTION 9100
HEAD CAPE TECAWELD
SWEATBAND 9100 & 9100 FX PK=2
SWEATBAND 9100 & 9100 FX PK=5
SWEATBAND 9100 & 9100 FX PK=50
LENS MAGNIFYING 1.0X 9100 100 & 9000
LENS MAGNIFYING 1.5X 9100 100 & 9000
LENS MAGNIFYING 2.0X 9100 100 & 9000
LENS MAGNIFYING 2.5X 9100 100 & 9000
LENS MAGNIFYING 3.0X 9100 100 & 9000
BATTERY LITHIUM 9100, 100 & 9000 PK=2
LENS WELDING 9100XXi SPEEDGLAS
VISOR PLATE 9100 FX PK=5
VISOR PLATE ANTI-FOG 9100 FX PK=5
LENS COVER OUTER STD 9100 PK=10
COVER LENS OUTER HC 9100 PK=10
LENS COVER OUTER HT 9100 PK=10
LENS COVER INNER 9100XX PK=5
HOLDER BATTERY 9100
SIDEWINDOWS COVER PLATE 9100 FX PK=2
HEAD HARNESS 9100
AIR DUCT ASSEMBLY 9100 FX AIR
ADAPTOR ADFLO BREATHING TUBE 9100 FX AIR
FACE SEAL 9100 FX AIR
AIR DEFLECTOR 9100 FX AIR
HEAD HARNESS PIVOT MECHANISM 9100
Part No
169006
169007
169010
169100
169502
169505
169550
Description Part No Description Part No Description Part No Description Part No Description
HEAD HARNESS FRONT PART 9100
HEAD HARNESS BACK PART 9100
FRONT COVER KIT 9100 FX
HELMET WELDING 9100 FX AIR EXC LENS
CARRY BAG SPEEDGLAS
To request a quote or place an order for spare parts, please contact TWS on [phone] or visit www.tweld.com.au. Please note that higher than normal levels
of pollutants, heat and sparks will require more frequent replacement of components. If you require additional guidance, please check the care and maintenance videos on our
YouTube Channel (www.youtube.com/user/3MSpeedglas) or contact your local TWS representative.
Further information and advice
Authorised 3M Wholesaler
Unit 13, 39 Herbert Street • St Leonards NSW 2065 • Australia
T: [phone] • F: [phone]
E: [e-mail]
W: www.speedglas.com.au
16 95 02
16 95 05
16 95 50
79 01 01
53 35 05

3M™Versaflo™V-500E Regulator
To maintain protection levels, optimise the effective lifetime of the system and avoid the additional cost of
replacement, it is extremely important to carry out regular checks and maintenance on Powered and Supplied Air
Respirators.
• Ensure couplings are securely fitted
• Inspect breathing tube - ensure it is free from splits or
holes. Replace if necessary
• Inspect belt - ensure it is free from splits or tears and
the buckle is undamaged
• Replace filter if odour is detected during use
Before use After use
• Clean casing with cloth dampened with a mild solution of water and
liquid household soap
• Disinfect surfaces with 3M 504 Cleaning Wipes
• Store in a dry, clean area / locker away from direct sunlight, high
temperatures and solvents
Care & Maintenance
ADAPTOR QRS BREATHING TUBE TO 9000
TUBE BREATHING SELF ADJUSTING QRS ADFLO
TUBE BREATHING HEAVYDUTY RUBBER QRS ADFLO
TUBE BREATHING COVER FLAME RESISTANT ADFLO
REGULATOR V-500E WITH BELT
CARBON FILTER & TWO O-RINGS SAR
HOSE BREATHING AIR 5M WITH CEJN FITTINGS
Part No
533506
834016
834017
834018
852017
895110
BAHOSE05M
Description Part No Description Part No Description
To request a quote or place an order for spare parts, please contact TWS on [phone] or visit www.tweld.com.au. Please note that higher than normal levels
of pollutants, heat and sparks will require more frequent replacement of components. If you require additional guidance, please check the care and maintenance videos on our
YouTube Channel (www.youtube.com/user/3MSpeedglas) or contact your local TWS representative.
Further information and advice
Authorised 3M Wholesaler
Unit 13, 39 Herbert Street • St Leonards NSW 2065 • Australia
T: [phone] • F: [phone]
E: [e-mail]
W: www.speedglas.com.au
Monthly
• Carry out all the ’Before Use’ inspections and create
record of this monthly check for the regulator
Six Monthly
• Change carbon filter
BAHOSE10M
BAHOSE15M
BAHOSE20M
BAHOSE30M
BAHOSE40M
C103421004
C103425004
HOSE BREATHING AIR 10M WITH CEJN FITTINGS
HOSE BREATHING AIR 15M WITH CEJN FITTINGS
HOSE BREATHING AIR 20M WITH CEJN FITTINGS
HOSE BREATHING AIR 30M WITH CEJN FITTINGS
HOSE BREATHING AIR 40M WITH CEJN FITTINGS
COUPLING HOSE CONNECTION 10MM (3/8)
NIPPLE HOSE CONNECTION 10MM (3/8)
C103425152 NIPPLE MALE THREAD R 1/4 (82155)
BAHOSE05M
BAHOSE10M
BAHOSE15M
BAHOSE20M
BAHOSE30M
BAHOSE40M
83 40 18
83 40 16
83 40 17
C103425152
53 35 06
85 20 17
89 51 10
85 20 16
80 60 00
85 30 64
C102201004
C103421004
C103425152
85 21 05
85 70 00
C102211292
C103425004