4IPNET OWL400 User manual

OWL400/410
V1.00

Quick Installation Guide
O W L 4 0 0 / 4 1 0 L o n g R a n g e O u t d o o r A P / B r i d g e / C P E ENGLISH
- 1 -
Copyright N otic e
This document is protected by U S A copyrig ht l a w s a nd other l a w s a nd is the property of
4 I P N E T, I N . Y ou ma y not copy, reproduce, distribute, publ ish, displ a y, perf orm, or
modif y a ny pa rt of this publ ica tion in a ny f orm or by a ny mea ns w ithout prior w ritten
permission f rom 4 I P N E T, I N . Y ou ma y not a l ter or remov e a ny copyrig ht or other notice
f rom copies of the content. Al l other bra nd a nd product na mes a re cl a imed or
reg istered ma rk s of their respectiv e compa nies or org a niz a tions.
Al l rig hts reserv ed.
4Gon www.4Gon.co.uk [email protected] Tel: [phone] Fax: [phone]

Quick Installation Guide
O W L 4 0 0 / 4 1 0 L o n g R a n g e O u t d o o r A P / B r i d g e / C P E ENGLISH
- 2 -
Preface Pack ag e C o n t en t s
The 802.11 n/a compliant OWL400/410 is a Long
Range Outdoor AP/ Bridge/ CPE device that can be
used for dual purposes. First, it can be deployed as
a traditional fixed wireless Access Point (AP).
Secondly, it can be used as a Customer Premises
Equipment (CPE) that connects to the outdoor
wireless network of Wireless Internet Service
Provider (WISP).
The metal sealed OWL400/410 is compact in size
and weatherproof. Coming with a mounting kit, it
can be mounted on a pole or wall. It is suitable for
both indoor and outdoor usage with its 200mW
output power, which is higher than a typical indoor
AP (100mW).
This Quick Installation Guide (including FAQ
Instruction Guide) provides instructions for getting
started with OWL400/410.
1. OWL400/410 x 1
2. Quick Installation Guide (QIG) x 1
3. CD-ROM (with User’s Manual and QIG) x 1
4. Power Sourcing Equipment (PSE) with
AC cable x 1
5. Mounting Kit x 1
It is recommended to keep the original
packing material for possible future shipment
when repair or maintenance is required. Any
returned product should be packed in its
original packaging to prevent damage during
delivery.
4Gon www.4Gon.co.uk [email protected] Tel: [phone] Fax: [phone]

Quick Installation Guide
O W L 4 0 0 / 4 1 0 L o n g R a n g e O u t d o o r A P / B r i d g e / C P E ENGLISH
- 3 -
System Overview
OWL400
1 Power Green LED ON indicates power on, and OFF indicates power off
2 WLAN Green LED ON indicates system ready
3 LAN Green LED ON indicates connection; BLINKING indicates
transmitting data; OFF indicates no connection
4 PoE Connector For connecting to the Power Sourcing Equipment (PSE)
5 Reset Press more than 5 seconds and release to reset the system to its
default settings
6 Primary N-type Antenna
Connector For connecting to an antenna
7 N-type Connector For connecting to an antenna
Note:
Reset Back to Factory Default:
Unscrew the screw beside the PoE hole. Press and hold the button for seconds. You can
use a toothpick to help you reach the button.
The system is meant to be used in only one mode at a time. Before you start with any
configuration, you should first decide which mode to use it in. Please prevent constant
switching from one mode to another during usage as it is easy for users to misconfigure the
settings.
4Gon www.4Gon.co.uk [email protected] Tel: [phone] Fax: [phone]

Quick Installation Guide
O W L 4 0 0 / 4 1 0 L o n g R a n g e O u t d o o r A P / B r i d g e / C P E ENGLISH
- 4 -
OWL410
1 Power Green LED ON indicates power on, and OFF indicates power off
2 WLAN Green LED ON indicates system ready
3 LAN Green LED ON indicates connection; BLINKING indicates
transmitting data; OFF indicates no connection
4 PoE Connector For connecting to the Power Sourcing Equipment (PSE)
5 Reset Press more than 5 seconds and release to reset the system to its
default settings
6 Built-in patch antenna 10 dBi (Horizontal: 110 degree; Vertical: 60 degree)
4Gon www.4Gon.co.uk [email protected] Tel: [phone] Fax: [phone]

Quick Installation Guide
O W L 4 0 0 / 4 1 0 L o n g R a n g e O u t d o o r A P / B r i d g e / C P E ENGLISH
- 5 -
H a rd wa re I n sta l l a tio n
OWL400/410
The following diagram is a basic network topology which can be used for testing and configuring the
OWL400/410.
Installation Steps:
Step 1. Connect the antennas to the connectors.
Step 2. Connect the PSE (POWER & DATA OUT) to the PSE 1 connector on the lower panel.
Step 3. Connect one end of an Ethernet cable to the PSE 2 connector on the lower panel and the other end
to a computer.
Step 4. Connect the power cord to the PSE.
Step 5. Power on the PSE in order to supply power to the OWL400/410.
4Gon www.4Gon.co.uk [email protected] Tel: [phone] Fax: [phone]

Quick Installation Guide
O W L 4 0 0 / 4 1 0 L o n g R a n g e O u t d o o r A P / B r i d g e / C P E ENGLISH
- 6 -
G ettin g Sta rted
4ipnet OWL400/410 supports web-based configuration. OWL400/410 is a dual-mode system, AP Mode as the
default mode for the first time entering the system, which also can be configured as either an access point (AP
Mode) or a gateway (CPE Mode) based on your needs. It is required to follow the respective installation
procedures provided to properly set up the desired mode for this system.
•Default IPAddress of Web Management Interface:
The default IP address and Subnet Mask for the AP mode and CPE mode are as follows:
Mode AP Mode CPE Mode
IP Address 192.168.1.1 192.168.1.1
Subnet Mask 255.255.255.0 255.255.255.0
•Default User Name and Password:
There is only one management account for AP mode, root. In addition, there are two system management
accounts for CPE mode to maintain the system, root and admin, and each has different levels of management
capabilities. The root account is empowered with full privileges while the admin account is with partial ones.
The default user name and password for both the root and admin account are as follows:
Mode AP Mode CPE Mode
Management
Account Root Account Root Account Admin Account
User Name root root a dmin
Password a dmin a dmin a dmin
4Gon www.4Gon.co.uk [email protected] Tel: [phone] Fax: [phone]

Quick Installation Guide
O W L 4 0 0 / 4 1 0 L o n g R a n g e O u t d o o r A P / B r i d g e / C P E ENGLISH
- 7 -
Step 1: IP Segment Setup for Administrator PC
Set a static IP address on the same subnet mask as OWL400/410 in TCP/IP of the administrator PC, such as
the following example. Do not duplicate the IP address used here with the IP address of OWL400/410 or any
other devices within the same network.
>> Example of IP Segment:
The valid range of IP address is 1 ~ 254. However, 1must be avoided as it is already used by OWL400/410.
Below depicts an example of using 100 (the underlined value can be changed as desired).
IPAddress: 192.168.1.100
Subnet Mask: 255.255.255.0
Step 2: Launch Web Browser
Launch a web browser to access the web management interface of AP mode by entering the default IP
address, http://192.168.1.1/, in the URL field, and then press Enter.
Using an incorrect default IP address will result in no Login page
shown in the web browser. Please make sure a correct IP
address is used for the desired mode.
Step 3: System Login
The system manager Login Page will then appear.
Enter “root” in the User name field and “admin” in the Password field, and then click Login to log in.
4Gon www.4Gon.co.uk [email protected] Tel: [phone] Fax: [phone]

Quick Installation Guide
O W L 4 0 0 / 4 1 0 L o n g R a n g e O u t d o o r A P / B r i d g e / C P E ENGLISH
- 8 -
Step 4: Login Success
After a successful login to OWL400/410, a System Overview page of web management interface will appear,
To logout, simply click on the Logout button at the upper right hand corner of the interface.
Note:
By default, AP mode is enabled. Therefore, the
administrator must access the system via theAP
mode login page for the first time. The administrator is
then able to switch between modes afterwards.
4Gon www.4Gon.co.uk [email protected] Tel: [phone] Fax: [phone]

Quick Installation Guide
O W L 4 0 0 / 4 1 0 L o n g R a n g e O u t d o o r A P / B r i d g e / C P E ENGLISH
© 2 0 0 9 4 I P N E T , I N C . - 9 -
C o mmo n Settin g s
<AP Mode – Default Mode>
Step 1: Mode Confirmation
Ensure the Operating Mode is currently in AP mode.
Click on the Status button and then select the System Overview tab. The Operating Mode is at the
System section on the System Overview page.
4Gon www.4Gon.co.uk [email protected] Tel: [phone] Fax: [phone]