4IPNET OWL530 v1.00 User manual

OWL530 v1.00
Outdoor Access Point/Bridge/CPE

Quick Installation Guide
OWL530 Outdoor AP/Bridge/CPE ENGLISH
Copyright © 4IPNET, INC. All rights reserved.
i
Copyright Notice
This document is protected by USA copyright laws and other laws. Besides,
the document is the property of 4IPNET, INC. You may not copy, reproduce,
distribute, publish, display, perform, or modify any part of this publication in
any form or by any means without prior written permission from 4IPNET, INC.
You may not alter or remove any copyright or other notice from copies of
the content. All other brand and product names are claimed or registered
marks of their respective companies or organizations.
All rights reserved.
To download up-to-date version, please visit www.4ipnet.com.

Quick Installation Guide
OWL530 Outdoor AP/Bridge/CPE ENGLISH
Copyright © 4IPNET, INC. All rights reserved.
ii
FCC CAUTION
This equipment has been tested and proven to comply with the limits for a class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
---Reorient or relocate the receiving antenna.
---Increase the separation between the equipment and receiver.
---Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
---Consult the dealer or an experienced radio/TV technician for help.
The device contains a low power transmitter which will send out Radio Frequency (RF) signal when
transmitting. This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with a minimum distance of
20 centimeters between the radiator and your body.

Quick Installation Guide
OWL530 Outdoor AP/Bridge/CPE ENGLISH
Copyright © 4IPNET, INC. All rights reserved.
iii
CE CAUTION
Declaration of Conformity with Regard to the 1999/5/EC (R&TTE Directive) for
European Community, Switzerland, Norway, Iceland, and Liechtenstein
Model: OWL530
For 2.4 GHz radios, the device has been tested and passed the requirements of the following standards,
and hence fulfills the EMC and safety requirements of R&TTE Directive within the CE marking
requirement.
• Radio: EN 300.328:
• Radio: EN 50392
• EMC: EN 301.489-1, EN 301.489-17,
• EMC: EN 55022Class B, EN 55024:+ A1 + A2including the followings:
EN 61000-3-2, EN 61000-3-3.
EN 61000-4-2, EN 61000-4-3, EN 61000-4-4,
EN 61000-4-5, EN 61000-4-6, EN 61000-4-11
• Safety: EN 60950-1 + A11,
Caution:
This declaration is only valid for configurations (combinations of software, firmware, and hardware)
provided and supported by 4ipnet Inc. The use of software or firmware not provided and supported
by 4ipnet Inc. may result in the equipment no longer being compliant with the regulatory
requirements.
European standards dictate maximum radiated transmit power of 100mW EIRP and frequency range
2.400-2.4835 GHz. This equipment is intended to be used in all EU and EFTA countries. Outdoor use
may be restricted to certain frequencies and/or may require a license for operation. Contact your local
regulatory authority for compliance.
Taiwan NCC Statement
根據 NCC 低功率電波輻射性電機管理辦法 規定:
第十二條
經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或
變更原設計之特性及功能。
第十四條
低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時應立即停用，並改善至
無干擾時方得繼續使用。
前項合法通信，指依電信法規定作業之無線電通信。
低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之擾。
在5.25 ~ 5.35 秭赫頻帶內操作之無線資訊傳輸設備，限於室內使用。

Quick Installation Guide
OWL530 Outdoor AP/Bridge/CPE ENGLISH
- 1 -
Preface
Package Contents
The 802.11 n/a/b/g compliant OWL530 is an
OutdoorAP/Bridge/CPE device that can be used for
multiple purposes. It can be deployed as a
traditional fixed wireless Access Point (AP) or it can
be used as a Customer Premises Equipment (CPE)
that connects to the outdoor wireless network of
Wireless Internet Service Provider (WISP).
Capsulated in weather-proof IP68 metal chassis
and powered by 802.3af/at PoE, OWL530 comes in
a small footprint for pole-/wall-mount unit that meets
most rough outdoor environment for continuously
providing outdoor clients’accesses or wireless
bridge to a peer node or surveillance device via 11n
wireless connection.
When OWL530 operates in CPE mode, it acts as a
wireless modem, connecting wirelessly to the
Internet upstream while serving broadband
connection to client devices downstream. This
mode is ideal in many WISP solutions, where
last-mile connectivity often involves serving
high-speed Internet to locations where physical
cabling is impossible.
This Quick Installation Guide (including FAQ
Instruction Guide) provides instructions for getting
started with OWL530.
1. 4ipnet OWL530 x 1
2. Ground Cable x 1
3. Quick Installation Guide (QIG) x 1
4. Power Sourcing Equipment (PSE) with
AC cable x 1 (Optional)
5. Mounting Kit x 1
It is recommended to keep the original
packing material for possible future shipment
when repair or maintenance is required. Any
returned product should be packed in its
original packaging to prevent damage during
delivery.

Quick Installation Guide
OWL530 Outdoor AP/Bridge/CPE ENGLISH
- 2 -
System Overview
OWL530
1
Ventilation Valve
Due to extreme weather conditions, water vapor in the OWL530
may condense. The valve allows ventilation to prevent moisture
buildup within the OWL530.
2
Ground Connector
For connecting the ground wire.
3
PoE Connector
For connecting to the Power Sourcing Equipment (PSE).
4
N-type Connector x 2
For connecting to an antenna
4 (1) is the primary antenna connector and 4 (2) is the secondary.
Utilize both connectors for 802.11n MIMO optimized performance.
Parts
5
Detachment Tool
For detaching the RJ45 connector from the PoE Port
6
Pole Mount Kit
Includes two U-shaped bolts, 8 hex nuts and 8 split washers
7
Ground Wire
For ground connection as mentioned in 2

Quick Installation Guide
OWL530 Outdoor AP/Bridge/CPE ENGLISH
- 3 -
Hardware Installation
OWL530
The following diagram is a basic network topology which can be used for testing and configuring the
OWL530.
Installation Steps:
Step 1. Connect two N-type antennas to the N-type connectors
Step 2. Connect one end of an Ethernet cable to the PSE (POWER & DATA OUT) to the PSE and one end
to the OWL530.
Inserting the RJ45 connector to the OWL530
- Unscrew the cap on the PoE Port (C)

Quick Installation Guide
OWL530 Outdoor AP/Bridge/CPE ENGLISH
- 4 -
- Insert the RJ45 cable through the outer opening of cap (C)
- Insert the RJ45 connector and wrap (A) around the Ethernet cable through the slit between the
connector and cap (C)
- Wrap (B) around (A) through the slit on (B)

Quick Installation Guide
OWL530 Outdoor AP/Bridge/CPE ENGLISH
- 5 -
- Insert Parts (A) and (B) together into the PoE Port
- Screw cap (C) onto the PoE Port
Step 3. Connect one end of another Ethernet cable to the PSE (Data Link) and the other end to a computer.
Step 4. Connect the power cord to the PSE.
Step 5. Power on the PSE in order to supply power to the OWL530.
Mounting the OWL530
The diameter of poles mountable by the OWL530 mounting kit is from 40mm ~ 60mm
Step 1. Screw nuts onto the U-shaped bolts and insert bolts through the split washers.
Note:
Please do NOT remove or tamper with the ventilation valve as it has been
pre-installed and secured.

Quick Installation Guide
OWL530 Outdoor AP/Bridge/CPE ENGLISH
- 6 -
Step 2. Align the front of OWL530 with the pole and insert the U-shaped bolts into the 4 holes on the corners
of the OWL530.
Step 3. Secure the OWL530 by screwing on the nuts after the inserting the washers for all four corners.

Quick Installation Guide
OWL530 Outdoor AP/Bridge/CPE ENGLISH
Copyright © 4IPNET, INC. All rights reserved.
- 7 -
Getting Started
4ipnet OWL530 supports web-based configuration. OWL530 is a dual-mode system where AP Mode is the
default mode, can be configured as either an access point (AP Mode) or a gateway (CPE Mode) based on
your deployment needs. It is required to follow the respective installation procedures provided to properly set
up the desired mode for this system.
Default IP Address of Web Management Interface:
The default IP address and Subnet Mask for the AP mode and CPE mode are as follows:
Mode
AP Mode
CPE Mode
IP Address
192.168.1.1
192.168.1.1
Subnet Mask
255.255.255.0
255.255.255.0
Step 1: IP Segment Setup for Administrator PC
Set a static IP address on the same subnet mask as OWL530 in TCP/IP of the administrator PC, such as the
following example. Do not duplicate the IP address used here with the IP address of OWL530 or any other
devices within the same network.
>> Example of IP Segment:
The valid range of IP address is 1 ~ 254. However, 1must be avoided as it is already used by OWL530. Below
depicts an example of using 100 (the underlined value can be changed as desired).
IPAddress: 192.168.1.100
Subnet Mask: 255.255.255.0
Step 2: Launch Web Browser
Launch a web browser to access the web management interface of AP mode by entering the default IP
address, http://192.168.1.1/, in the URL field, and then press Enter.

Quick Installation Guide
OWL530 Outdoor AP/Bridge/CPE ENGLISH
Copyright © 4IPNET, INC. All rights reserved.
- 8 -
Step 3: System Login
The system manager Login Page will then appear.
Enter “admin”in the User name field and “admin” in the Password field, and then click Login to log in.

Quick Installation Guide
OWL530 Outdoor AP/Bridge/CPE ENGLISH
Copyright © 4IPNET, INC. All rights reserved.
- 9 -
Step 4: Login Success
After a successful login to OWL530, a System Overview page of web management interface will appear,
To logout, simply click on the Logout button at the upper right hand corner of the interface.
Note:
AP mode is the default mode. The administrator must access the system via theAP
mode login page first before switching modes.

Quick Installation Guide
OWL530 Outdoor AP/Bridge/CPE ENGLISH
Copyright © 4IPNET, INC. All rights reserved.
- 10 -
Common Settings
<AP Mode –Default Mode>
Step 1: Mode Confirmation
Ensure the Operating Mode is currently in AP mode.
Click on the Status button and then select the System Overview tab. The Operating Mode is at the
System section on the System Overview page.

Quick Installation Guide
OWL530 Outdoor AP/Bridge/CPE ENGLISH
Copyright © 4IPNET, INC. All rights reserved.
- 11 -
Step 2: Change Password
Click on the Utilities button and then select the Password tab.
Enter a new password in the New Password field and retype it in the Re-enter New Password field.
Click SAVE to save the changes.

Quick Installation Guide
OWL530 Outdoor AP/Bridge/CPE ENGLISH
Copyright © 4IPNET, INC. All rights reserved.
- 12 -
Step 3: Network Settings
【Example Settings】
Click on the System button and then select the Network Interface tab.
Click the Static radio button and enter the related information in the fields marked with red asterisks.
Click SAVE to save the settings.

Quick Installation Guide
OWL530 Outdoor AP/Bridge/CPE ENGLISH
Copyright © 4IPNET, INC. All rights reserved.
- 13 -
Step 4: SSID Settings
Click on the Wireless button and select the General tab.
Band: Select an appropriate band from the drop-down list box.
Click on the Wireless button and select the VAP Config tab.
ESSID: Enter respective ESSID for each VAP in the ESSID field or use the default. ESSID (Extended
Service Set Identifier) is a unique identifier used for networking devices to get associated with OWL530.
Click SAVE to save the settings.

Quick Installation Guide
OWL530 Outdoor AP/Bridge/CPE ENGLISH
Copyright © 4IPNET, INC. All rights reserved.
- 14 -
Step 5: Security Settings
Click on the Wireless button and then select the Security tab.
Select the desired VAP Profile and Security Type from the drop-down list boxes. The system supports
various WiFi standard security such as WEP, WPAPersonal, WPA Enterprise, and 802.1X. The above
figure depicts an example of selecting VAP-1 and WEP.
Enter the information required in the blank fields.
Click SAVE to save all settings configured so far; all updated settings will take effect upon reboot.
Congratulations!
AP mode is now successfully configured.

Quick Installation Guide
OWL530 Outdoor AP/Bridge/CPE ENGLISH
Copyright © 4IPNET, INC. All rights reserved.
- 15 -
<CPE Mode>
Step 1: Mode Confirmation
Ensure the Operating Mode is currently in CPE mode.
Click on the Status button and then select the System Overview tab. The Operating Mode is at the
System section on the System Overview page.

Quick Installation Guide
OWL530 Outdoor AP/Bridge/CPE ENGLISH
Copyright © 4IPNET, INC. All rights reserved.
- 16 -
Step 2: Change Password
Click on the Utilities button and then select the Password tab.
Change Admin Account Password
Enter a new password in the New Password field and retype it in the Re-enter New Password field.
Click SAVEto save the changes.