Aaeon Onyx-151 User manual

Onyx-151
Professional Panel PC / LCD PC
Quick Installation Guide
NOTE:
This guide is designed for experienced users to setup the
system within the shortest time. For detailed information,
pleasealwaysrefertoelectronicuser`smanualinthe
supportingCD-ROM.

A. Perspectives ........................................................ 1
B. Specifications ...................................................... 2
C. Onyx-151 in a desktop stand ............................... 3
D. Onyx-151 in a tilting stand .................................. 4
E. Onyx-151 in a swival arm ................................... 5,6
F. Panel mounting .................................................. 7
G. Cut out for panel mounting ................................. 8
H. Remove speaker panel to upgrade CPU & RAM .... 8
I. CPU configuration ............................................... 9
J. DRAM installing ............................................... 10
K. HDD/CD-ROM/FDD installing .......................... 11
To remove the HDD/CD-ROM/FDD module 11
To remove the backplane from the module .. 11
To insert a 2.5 inches HDD ......................... 12
To secure HDD, FDD, CD-ROM ................... 13
L. Dimensions ...................................................... 14
M. I/O ports .......................................................... 15
N. COM2 RS-232/422/485 select (J10,J7) ............. 16
Contents

1
A. Perspectives
Desktop
Tilting
Swivel arm mounting
Panel mounting
Onyx-151 Quick Installation Guide

Onyx-151 Quick Installation Guide
2
B. Specifications
Onyx-151 General Specifications
LCD 15 color TFT 1024x768, 200 cd/m2 high brightness
Power supply 100W 90~240VAC (optional 18~36VDC or 36~72VDC power supply)
CPU Cerelon socket370 CPU, Coppermine PIII coming soon
Memory Up to 256MB
HDD One 2 5 hard drive
FDD One 3 5 slim floppy drive
CD-ROM drive One 24X CD-ROM drive
Flash disk DiskOnChip from M-system
Networking (LAN) 10/100 Base-T
COM ports 1x RS-232, 3x RS-232/422/485
Parallel port Yes
PS/2 mouse & K/B Yes
VGA port Yes
Bus expansion NIL
Touch screen Resistive touch screen (optional)
USB Yes
I/O
Audio Yes
Watchdog timer Yes
Infrared transmission Yes
Brightness control Yes
Mounting Desktop stand (standard), Tilting kit (optional), Swivel arm (optional)
Panel mounting (standard)
Front panel meets IP-65, NEMA 4/12 Yes
PC module 0~60 JOperation
Temperature LCD module 0~50 J

Onyx-151 Quick Installation Guide 3
C. Onyx-151 in a desktop stand
Rear view
Side view 25 degree pitch allowance

Onyx-151 Quick Installation Guide 4
D. Onyx-151 in a tilting stand

Onyx-151 Quick Installation Guide
5
E. Onyx-151 in a swival arm
VESA standard
mountingholes

Onyx-151 Quick Installation Guide 6

Onyx-151 Quick Installation Guide
7
F. Panel mounting

Onyx-151 Quick Installation Guide
G. Cut out for Panel mounting
H. Remove speaker panel to upgrade CPU & RAM
8

Onyx-151 Quick Installation Guide 9
CPU core frequency = CPU frequency ratio (2~5.5)*External bus
clock (66 or 100Mhz)
CPU
FREQUENCY
RATIO SW1(4) SW1(5) SW1(6)
2X ON OFF OFF
2.5X ON OFF ON
3X ON ON OFF
3.5X ON ON ON
4X OFF OFF OFF
4.5X OFF OFF ON
5X OFF ON OFF
* 5.5X OFF ON ON
* Default
Note :
Most requency ratio of Celeron CPUs are pre-locked within the CPUs.
These CPUs run at fixed speed (frequency) regardless of the
configurations listed above.
If the CPU you are using requires higher ratio than 5.5X, it is most
likely pre-locked.
I. CPU configuration

Onyx-151 Quick Installation Guide
10
System Memory
The left edge of the Onyx-151 MAIN BOARD contains a socket for
168-pin dual inline memory module (DIMM). The socket uses 3.3 V
unbufferedsynchronous DRAM(SDRAM). DIMM isavailable in
capacities of 16, 32, 64, or 128 MB. The socket can be filled in the
DIMM of any size, giving your Onyx-151 MAIN BOARD between 16
and 128 MB of memory.
Supplementary information about DIMM
Your Onyx-151 MAIN BOARD can accept both regular and PC-100
SDRAMDIMM Module(withorwithout parity).However,if the
Pentium II 350MHz or up CPU is used, The Onyx-151 MAIN BOARD
can only accept PC-100 SDRAM DIMM Module. Single-sided modules
are typically 16 or 64 MB; double-sided modules are usually 32 or
128MB.
Memory Installation Procedures
To install DIMM, first make sure the two handles of the DIMM
socket are in the open” position. i.e. The handles remain outward.
Slowly slide the DIMM module along the plastic guides on both
ends of the socket. Then press the DIMM module right down into
the socket, until you hear a click. This is when the two handles
J. DRAM installing

Onyx-151 Quick Installation Guide
K. HDD/CD-ROM/FDD installation
11
Toremovethe HDD/CD-ROM/FDDmodule
Toremove thebackplanefrom themodule

Onyx-151 Quick Installation Guide
12
Toinstalla 2.5 inches HDD

Onyx-151 Quick Installation Guide 13
To secure HDD, FDD, CD-ROM
Note:
1. FDD & CD-ROM should be intalled before HDD
2. HDD should always attach to the backplane
first before sliding into the module
3. There should be a mylar at the bottom of the
module to protect HDD from grounding. If not,
please check with your supplier.

Onyx-151 Quick Installation Guide
14
L. Dimensions

Onyx-151 Quick Installation Guide 15
M. I/O ports

Onyx-151 Quick Installation Guide
N. COM2 RS-232/422/485 select (J10, J7)
16
COM2 RS-232/422/485 select (J10, J7)
TheCOM2serialportcanbeselectedasRS-232,RS-422,orRS-485
by setting J10 & J7.
COM2 Select (J10, J7)
RS-232* RS-422 RS-485
J10
J7
*default
1 3 5
2 4 6
1 3 5
2 4 6
1 4 7 10
3 6 9 12
1 4 7 10
3 6 9 12
1 4 7 10
3 6 9 12
1 3 5
2 4 6