ABB ACS 800 Series User manual

—
ABB LOW VOLTAGE AC DRIVES, WIND TURBINE CONVERTERS AND SOLAR INVERTERS
Converter modules with electrolytic DC
capacitors in the DC link
Capacitor reforming instructions

—

3
Table of contents
1. Introduction
Contents of this chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Applicability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
ABB low voltage AC drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
ABB wind turbine converters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
ABB solar inverters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Target audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Purpose of the manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2. Reforming the capacitors
Contents of this chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Overview of the reforming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Reforming time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Checking the converter age . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Reforming with power on for 30 minutes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Reforming with external DC power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Reforming with external diode bridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Further information

4

Introduction 5
1
Introduction
Contents of this chapter
This chapter describes the applicability, target audience and purpose of this manual and
safety instructions.
Applicability
This manual applies to converter modules which have electrolytic DC capacitors in the DC
link. The subsections below list the converter module types and product series in more
detail for each product area. All converter module types are referred to as converter or
converter module in this manual.
Note: A drive module is used in all connection diagrams. The connection principle is the
same for the other converter module types as well but the terminal markings can vary.
ABB low voltage AC drives
This manual applies to drive, inverter, IGBT supply and three-phase brake modules in
product series ACS800, ACS850, ACQ810, ACSM1, ACS380, ACH480, ACS480,
ACH580, ACQ580, ACS580 and ACS880, that is, the following module types:
•ACS800-01, -11, -31, -02, -04, -104 and -104LC
•ACS850-04
•ACQ810-04
•ACSM1-04 and ACSM1-204
•ACS380
•ACH480
•ACS480
•ACH580-01, -04, -31 and 34

6 Introduction
•ACQ580-01, -04, -31 and -34
•ACS580-01 and -04
•ACS880-01, -04, -11, -31, -14, -34 and -104.
ABB wind turbine converters
This manual applies to line-side converter modules and generator-side converter modules
in product series ACS800-67LC, ACS800-77LC, ACS800-87LC and ACS800N-87LC.
Note: ACS800-67 and ACS800-77 modules include film capacitors in the DC link instead
of electrolytic capacitors.The film capacitors do not need to be reformed.
ABB solar inverters
This manual applies to solar inverter modules in product series PVS800-57 and PVS800-
57B.
Target audience
You are expected to know the standard electrical wiring practices, electronic components,
and electrical schematic symbols.
Purpose of the manual
The manual provides information needed for reforming the converter module capacitors.
Safety instructions
WARNING! Obey the safety instructions delivered with the converter and given in
this manual. If you ignore them, injury or death, or damage to the equipment can
occur. If you are not a qualified electrical professional, do not do electrical
installation or maintenance work.
1. Drives: Never work on the converter, motor cable or motor when input power is
applied. After you have disconnected the input power, always wait for 5 minutes to let
the intermediate circuit capacitors to discharge before you start to work on the
converter, the motor or motor cable.
Wind turbine converters: Never work on the converter or generator when input power
is applied. After you have disconnected the input power, always wait for 10 minutes to
let the intermediate circuit capacitors discharge before you start to work on the
converter, generator or generator cable.
Solar inverters: Do not do work on the photovoltaic generator or the inverter or its input
or output cables when the inverter is connected to an electrical power system or to the
photovoltaic generator. After you have disconnected the inverter, always wait for 5
minutes to let the intermediate circuit capacitors discharge before you continue.
2. Measure that the installation is de-energized.
•Use a multimeter with an impedance of at least 1 Mohm.
•Make sure that the voltage between the converter input power terminals (U1, V1
and W1) and the grounding terminal (PE) is close to 0 V.
•Make sure that the voltage between the drive DC terminals (UDC+ and UDC-) and
the grounding terminal (PE) is close to 0 V.
3. Never switch on the converter power supply while the reforming circuit is connected.
Lock the disconnector (if any) to an open position.

Introduction 7
4. Make sure that the converter is clean and dry (no condensation) before you start the
reforming.

8 Introduction

Reforming the capacitors 9
2
Reforming the capacitors
Contents of this chapter
This chapter contains the instructions on how to reform the converter capacitors. It
contains three alternative methods.
Overview of the reforming
Electrolytic DC capacitors in the converter module DC link need to be reformed (re-aged) if
the module has been non-operational for a year or more. The reforming time depends on
how long the converter has been non-operational and on the converter module type.
Without reforming, the capacitors can get damaged when the converter starts to operate.
If the converter has been non-operational for less than one year, the capacitors do not
need reforming.
Besides the reforming methods presented in this manual, ABB can supply you with ready-
made reforming devices, such as FINERO FST-DCP 1500-05 and FUG HCK 800-2000.
For more information, contact your local ABB representative.
Reforming time
The intermediate circuit (DC link) of the converter is connected to its nominal voltage for
the reforming time to “wake up” the capacitors. The diagram below shows the required
reforming time.
If the converter has been stocked (non-operational) for one to two years (graph a), it can
be reformed with power on for 30 minutes method.
If the converter has been stocked (non-operational) for one to three years (graph b), it can
be reformed with power on for 30 minutes method. See section Reforming with power on
for 30 minutes on page 11.

10 Reforming the capacitors
If the non-operational time has been more than two (graph a) or three (graph b) years,
reform the converter using the method in section Reforming with external DC power
supply on page 11 or Reforming with external diode bridge on page 13.
Checking the converter age
The converter serial number defines the week when the converter was manufactured:
•7 digits: For example, in 3260034, 3 denotes manufacturing year (2003), 26
manufacturing week and 0034 running manufacturing number.
•8 digits: For example, in 14250125, 1 denotes manufacturing country (1 = Finland), 4
manufacturing year (2004), 25 manufacturing week and 0125 running manufacturing
number.
•10 digits: For example, in 1173200725, 1 denotes manufacturing country, 17
manufacturing year (2017), 32 manufacturing week and 00725 running manufacturing
number.
Reforming time (hours)
Non-operational time (years)
0
0
21 43 65
1
2
3
4
5
6
a) Product series ACS800, ACS850, ACQ810, ACSM1, ACS880-104, ACS380, ACH480 and
ACS480
b) Product series ACH580, ACQ580, ACS580 and ACS880 except ACS880-104
a b
1/2